• Geotechnical Engineering
• /
• v.12 no.3
• /
• pp.127-148
• /
• 1996

Recently, foundations of heavy structures such as bridge abutments have been built on slopes or near the crest of slopes at an increasing rate. Because the bearing capacity of such foundations is considerably lower than the bearing capacity of the same soil on a level ground, deep footings such as piles and caissons are often used. However, the costs of such methods are generally very high. One of the new techniques to overcome the problem is to place reinforcing members such as geosynthetics or metal strips horizontally at some depths beneath the footings. Rational methods of analysis to predict the bearing capacity of footings in reinforced slopes are therefore needed. This paper proposes an analytical method for estimating the increase in bearing capacity gained from the included horizontal strips or ties of tensile reinforcing in the foundation soil below the footing built near the crest of a slope. A failure mechanism, including the concept of'wide slab effect', adopted in the present study for analyzing the bearing capacity of foundations in reinforced slopes, is established through the observed model test behaviors described by Binquet SE Lee and Huang et al, and the Boussinesq solutions. The analytical results are then compared with the experimental data described in the paper by Huang et al. Also in order to properly evaluate the soil reinforcement interaction, typical pullout test values of the apparent friction coefficient, which usually vary with depths owing to both the increase of the shearing volume and the increase in local stress caused by soil dilatancy, are analyzed and related functionally. Furthermore, analytical parametric studies are carried out to investigate the effect and significance of various pertinent parameters associated with design of reinforced slope foundations. Keywords : Bearing capacity, Reinforced slope, Slab effect, Friction coefficient.

• Journal of the Korean GEO-environmental Society
• /
• v.4 no.1
• /
• pp.11-17
• /
• 2003

The existing geotextile reinforced soil wall methods have a demerit in terms of esthetic view because concrete panel or block are used as wall facing of the methods. If grass planting walls could be used in reinforced soil slope or wall methods, efficiency of the methods would be increased with maximization of advantage of the methods. In this study, some possible methods in which grass planting wall is used as wall facing are devised. A series of laboratory model tests were performed to investigate the behavior of newly devised methods in order to compare with the results of each others. As a major result, it was found that this kinds of grass wall facing methods could be accepted as a new construction method even in the sense of stability.

• Tunnel and Underground Space
• /
• v.25 no.3
• /
• pp.264-274
• /
• 2015

In this study, the applicability of geotextile mesh soil nails on slopes was evaluated by numerical analysis to reduce environmental problems which a general soil nailing might produce and to improve its economical efficiency and construction convenience. To this end, in situ pull-out tests were conducted for both general soil nail and geotextile mesh soil nail and their pull-out characteristics were analyzed. Also, finite difference method was used to verify the suitability of numerical simulation. Parameters for nail and ground conditions were selected and sensitivity analysis was performed for the evaluation of slope stability. In addition, analysis was performed by limit equilibrium method which is widely used for slope stability analysis in practice. As a result, if the nail diameter was same, there is no big difference between geotextile mesh soil nails and general soil nails in terms of slope stability. Therefore it can be expected that geotextile mesh soil nails could be effective for slope reinforcement since they could keep a slope as stable as general soil nails and give better economical efficiency and construction convenience than general soil nails.

• The Journal of Engineering Geology
• /
• v.23 no.3
• /
• pp.283-292
• /
• 2013

A calcareous rock slope failed during excavation of the slope for construction of a tunnel entrance. The slope is located at the construction site for widening highway in Yeongwol, Korea. Field surveys, laboratory tests, and numerical analyses were performed to determine the reason for the slope failure. The numerical analysis revealed that the safety factor of the slope before construction of the entrance was less than 1, and that this decreased after construction. After construction of the entrance, the sliding zone of the slope increased and slope stability decreased because the shear strain and plastic zone in the slope over the tunnel entrance showed an increase relative to the lower part of the slope. To enhance the stability of the slope for construction of the tunnel entrance, countermeasures such as rock bolts, rock anchors, and FRP (Fiber glass Reinforced Plastic) grouting were adopted in light of the field conditions. Serial field monitoring performed to confirm the reinforcing effects of the adopted countermeasures revealed a small amount of horizontal deformation of the slope soils, most of the elastic deformation that can regain its former value. In addition, the axial forces of the rock bolt and anchor were more strongly affected by slope excavation during construction of the tunnel entrance than by tunnel excavation or the rainy season, and the axial forces tended to converge after excavation of the tunnel. Therefore, we can confirm that the slope is currently safe.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1994.06c
• /
• pp.94-110
• /
• 1994

This paper Voposes a stabilizing method against landslide using slide suppressor wall reinforced with soil nails. Included are a Evuedlwe to predict earth Uessures acing on nailed-slide suppressor wall and a method of analysis of the laterally loaded concrete pile. Based rut the Voposed Vocedure, the emcignt installation type and inclusion angle of nails are analyzed. Also, optimum location of the slide suppressor wall composed of concrete panel and stabilizing pile is examined using the UC Vogram. Finally, an example is given to illustrate the analysis and desisa procedure of the proposed slope reinforcing method.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.10
• /
• pp.2794-2802
• /
• 2009

Soil nailing method is widely used in reinforcing slopes and excavating earth. The analysis of nail-reinforced slopes, generally require complicated computer programs. The purpose of this paper is suggest, Soil stability Chart for nailed slopes which are very useful for pre-design, rapidly design, and final check. Three slope types, three nail lengths and three nail angles are selected for the stability analysis by using limit equilibrium method form Bishop and French. From the above results, this study propose the reinforced design charts for examine the necessity of reinforcement can be examined. The suggested stability chart and Taylor's Slope Stability Chart, showed similar safety factors. This Soil Nailing design charts can provide the solutions for necessity of reinforcement, economical of nail's length ratio and installation angle as well.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1995.06a
• /
• pp.176-209
• /
• 1995

• Tunnel and Underground Space
• /
• v.16 no.2 s.61
• /
• pp.146-155
• /
• 2006

The target slope of this study, formed during the construction of highway, is the very high infinite slope where sliding began along the discontinuity. Although an attempt was made to stabilize the upper part of the slope by installing the rock anchors, large scale failure was occurred at the lower part if the reinforced area. Afterwards, subsequent failures were observed two times. To investigate the cause of the failure, residual shear strength was measured by performing the direct shear test of rock specimen of the site. The anchor design was based on the pull-out test. Considering the slope surface where the undulation was severe and the variation of strength was very large, buttressing was used to obtain the required anchoring capacity.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.03a
• /
• pp.677-685
• /
• 2009

From the result of precise field investigation and stability examination for the cut slope, following results were acquired. 1. The cause of the cut slope collapse seems that it came from complex actions such as the weathering rock itself, existing fault zone and crack from excessive blasting. 2. As a result of analysis, it is appeared that the cut slope can be in danger of plane destruction. 3. The reinforcement force is decided by the result of limit equilibrium analysis. 4. For reinforcement the method after relaxing the slope was judged as the most proper method to the cut slope as comparing/analyzing Rock Anchor, Rock Bolt and method after relaxing the slope.

• Journal of the Korean Geosynthetics Society
• /
• v.4 no.4
• /
• pp.47-56
• /
• 2005

With the need of efficient site use retaining walls have frequently used. Of them dry cast modular block wall(MBW), in which geogrid and concrete block are used is getting popular because of its simplicity and economical efficiency of construction. However, since this method is based on the theory of earth pressure, sands with good quality should be used. In contrast, reinforced soil slope(RSS) that the slope is less than $70^{\circ}$ can use wider range of soil than MBW. A hybrid reinforced geo-structure might be a good alternative in view of overcoming difficulty obtaining soils with good quality as well as maximizing the efficiency of site use. This method is composed of reinforced block wall and reinforced soil slope. In this method, reinforced block wall is constructed up to a certain height vertically at ground boundary first. Reinforced soil slope is then constructed on the block wall subsequently. This paper introduces several technical points that should be taken into account in design and construction.