• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.563-566
• /
• 2005

This study deals with the development of noncontact vibration measuring system for monitoring the safety of structures as bridges, buildings, stadiums, tall chimneys, and dams where vibration measurements are very difficult because of various restrictions. Final object is to develope the system and be commercial by theoretical and experimental studies using IT technology for three years.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.04a
• /
• pp.132-139
• /
• 2008

The blade vibration problem of bladed disk is the most critical subject to consider since it directly affects the stable performance of the engine as well as life of the engine. Especially, due to complicated vibration pattern of the bladed disk, more effort was required for vibration analysis and test. The research of measuring the vibration of the bladed disk, using NSMS(Non-intrusive stress measurement) instead of Aeromechanics testing method requiring slip ring or telemetry system with strain gauge, was successful. These testing can report the actual stresses seen on the blades; detect synchronous resonances that are the source of high cycle fatigue (HCF) in blades; measure individual blade mis-tuning and coupled resonances in bladed disks. In order to minimize the error being created due to heat expansion, the tip timing sensor is installed parallel to the blade trailing edge, yielding optimal result. Also, when working on finite element analysis, the whole bladed disk has gone through three-dimensional analysis, evaluating the family mode. The result of the analysis matched well with the test result.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1991.04a
• /
• pp.75-79
• /
• 1991

고도로 산업화가 진행됨에 따라 회전기계는 더욱 중요시되고 있으며 이의 성능 향상에 부단한 노력이 경주되고 있다. 특히 우주 시대의 개막과 더불어 우주선 및 인공위성에 사용하기 위해 초소형이며 초고속의 고성능회전모타 를 개발하기에 이르렀다. 한 예로서 미국립항공우주국(NASA)의 스페이스셔 틀에 사용되는 주엔진 터보펌프를 들 수 있는데 이 터보펌프는 접시만한 크 기로써 71000마력을 생성해 낸다. 이러한 가공할 만한 에너지 밀도와 유량을 감당해 내려면 종래의 회전기계보다는 훨씬 더 높은 회전속도를 가져야 한 다. 이러한 회전체는 큰 관성부하와 진 동 및 동안정성의 문제등을 내포하고 있다. 고성능 회전기계의 또다른 예로서 초정밀 가공용 공작기계를 들 수 있 다. 선반 혹은 밀링머신으로 초정밀가공을 행하기 위해서는 회전축의 진동이 극히 작아야 한다. 이와 같이 오늘날 갈수록 초고성능 초정밀도를 추구함에 있어서 회전축의 진동을 현장에서 모니터링하고 이 진동데이터를 분석하여 회전축을 제어하는 것이 강력히 요구되어진다. 따라서 in-situ 측정이 중요성 을 띠게 되었는데 이는 제어기술의 바탕이 되는 자료를 현장에서 제공할 수 있기 때문이다. 회전축 진동측정의 대상이 되는 것들은 모타, 발전기, 엔진 및 터빈등을 대표적으로 들 수가 있다. 여기서 소형회전기계의 축표면과 같 이 비교적 곡면을 이루고 있는 부분의 진동변위 측정에 신중한 고려가 요구 되어 진다. 이는 축의 곡면도에 따라 감도가 변화하기 때문이다. 따라서 평 판에 대한 calibration 챠트를 회전기계축진동 변위환상에 이용하면 곡률에 따라서 오차가 생기게 된다. 본 연구에서는 비접촉 축진동측정시 발생되는 오차에 대하여 검토하고자 한다. from the studies, the origin of ${\alpha}$$_1$peak was attributed to the detrapping process form trap with 2.88[eV] deep of injected space charge from the chathode in the crystaline regions. The origin of ${\alpha}$$_2$ peak was regarded as the detrapping process of ions trapped with 0.9[eV] deep originated from impurity-ion remained in the specimen during production process of the material, in the crystalline regions. The origin of ${\beta}$ peak was concluded to be due to the depolarization process of "C=0"dipole with the activation energy of 0.75[eV] in the amorphous regions. The origin of ${\gamma}$ peak was responsible to the process combined with the depolarization of "CH$_3$", chain segment, with the activation energy of carriers from the shallow trap with 0.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.27 no.2
• /
• pp.58-66
• /
• 2023

In this study, cable tension was measured using the vibration method, and a vision-based system was applied as a sensor to measure the displacement response of a cable in a non-contact method. In the vision-based system, the camera is installed in a location that considers the target structure and the field of view of the camera. However, it can be difficult to recognize the control points required to measure the displacement response of a structure as the target structure and other structures such as vehicles may be included in the image at the intended installation location. In this study, a distorted image including a vehicle shows inaccurate results in image analysis due to the installation position of the vision-based system. Accordingly, the image including the vehicle was eliminated by calculating the similarity between the two images. To verify the validity of the method of estimating the cable tension of cable-stayed bridges using the proposed method, the vibration method was applied to cable-stayed bridges in service to measure the tension.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.31 no.5
• /
• pp.227-234
• /
• 2018

Researches regarding measurement and control of the dynamic behavior of liquid such as sloshing have been actively on undertaken in various engineering fields. Liquid vibration is being measured in the study of tuned liquid dampers(TLDs), which attenuates wind motion of buildings even in building structures. To overcome the limitations of existing wave height measurement sensors, a method of measuring liquid vibration in a TLD using a laser Doppler vibrometer(LDV) and galvanometer scanner is proposed in this paper: the principle of measuring speed and displacement is discussed; a system of multi-point measurement with a single point of LDV according to the operating principles of the galvanometer scanner is established. 4-point liquid vibration on the TLD is measured, and the time domain data of each point is compared with the conventional video sensing data. It was confirmed that the waveform is transformed into the traveling wave and the standing wave. In addition, the data with measurement delay are cross-correlated to perform singular value decomposition. The natural frequencies and mode shapes are compared using theoretical and video sensing results.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.8 s.173
• /
• pp.50-56
• /
• 2005

This paper is described a development of an optical fiber displacement sensor. The optical fiber sensor using an intensity modulated measures the displacement between target and sensor. A prototype sensor is composed of a transmitting part, a receiving part and a signal processing circuit. The experiment was conducted not only the sensor performance but also factors that affect intensity. The main performance of this sensor is resolution of 0.37um and the non-linearity $0.7\%$ FS and the dynamic bandwidth of about 6.3kHz. As a result of rotation test, the prototype sensor showed an equivalent performance to a commercial eddy current sensor.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.40 no.1
• /
• pp.1-10
• /
• 2003

This paper is concerned with the fuzzy control scheme and PID controller for the vibration suppression control of a cantilever beam equipped with a laser sensor and an electromagnetic actuator. The PID controller is being widely used in industrial applications. However, it is difficult to determine the appropriate PID gains in nonlinear systems and systems with time variant characteristic and so on. In this paper, we design the fuzzy based PID controller of which output gains are adjusted automatically and the designed controller is applied to active vibration control of a cantilever beam using electromagnetic actuator with strong nonlinearity. The tuning PID parameters of proposed controller are determined by using Fuzzy algorithm. Effectiveness and performance of the designed controller are verified by both simulation and experiment results. Experimental results demonstrate that better control performance can be achieved in comparison with the PID cotroller.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2021.06a
• /
• pp.78-78
• /
• 2021

영상유속분석법은 비접촉식으로 유속을 측정하는 방법으로 특히 홍수시 하천의 표면유속을 안전하게 계측할 수 있어서 경제적이고 안전한 하천유속 측정 방법 중 하나이다. STIV는 영상의 휘도 정보를 시간 방향으로 나열하여 작성된 STI(Space-Time Image)에 나타나는 패턴의 기울기를 이용하여 유속을 산정하는 방법이다. 특히 STIV(Space-Time Image Velocimetry)는 기존 입자군의 상호상관법에 기초한 입자영상유속계와 달리 표식자의 유무와 상관없이 유속을 측정할 수 있어 적용성과 안정성이 확보된다. 하지만 영상의 상태가 불량한 경우 정확한 유속 측정이 난해하며 야간에는 별도의 조명 추가 및 태풍과 같은 악기상에서는 빗방울이 카메라에 맺히거나 수면의 진동, 구조물의 진동에 의한 영상의 상태가 불량하게 되어 측정 정도가 떨어진다. 이처럼 영상을 이용한 유속 계측에 있어 다양한 연구 및 기술개발이 요구되는 시점이다. 따라서 본 연구에서는 영상을 이용한 정확한 유속측정을 위해 STIV와 인공지능을 융합하여 정확한 유속 평가를 목적으로 한다. 우선 기존 STI에 의한 기울기 추정방법을 확장하여 딥러닝(CNN)에 의한 기울기 추정방법을 도입하였다. CNN은 일반적으로 이미지의 특성을 추출하는데 유용한 방법으로서 STI의 2차원 Fourier변환 이미지를 사용하여 패턴의 기울기를 감지하도록 학습하였고 적용 결과 기울기에 대한 인식율은 매우 양호하였으며 이를 이용한 실제 관측 영상에 적용한 결과 유속에 대한 정밀도도 매우 양호하게 나타났다. 또한 딥러닝을 적용한 STIV는 노이즈(진동, 화면 불량 등)가 있는 영상에서도 안정적으로 유속을 산정할 수 있으며 전파유속계를 이용한 실제 하천의 표면유속 관측치와 비교 검토 결과 매우 양호하게 유속을 평가하고 있는 것으로 나타났다.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.10
• /
• pp.974-984
• /
• 2012

This research introduces a new method to attenuate flip-over vibration generation in the flat blade windshield wiper by adjusting the contact pressure between the windshield glass and the blade. The knocking force in the flip-over action of the blade is decreased by inducing gradual tilting-over along the rubber strip of the blade. This gradual tilting-over is induced by introducing a non-uniform contact pressure distribution between the blade and windshield glass. The contact pressure distribution is adjusted by controlling the unloaded profile of the body spring in the blade using a procedure proposed in a previous study. Two blades, one blade designed to generate a uniform pressure distribution and the other designed to generate non-uniform pressure distribution, are developed using the procedure. Contact pressure distributions of the developed blades are measured using a special device and compared with the intended distributions confirming the similarities between the two groups. Vertical and lateral vibrations of the two blades are measured under realistic operating condition simulated by a wiper test rig. The vertical vibrations of the blade with non-uniform contact pressure are substantially smaller than corresponding vibrations of the blade with uniform contact pressure over the entire rubber strip.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.10 no.5
• /
• pp.601-610
• /
• 1986

The acoustic intensity in the very near field of a vibrating surface reveals information about the location of sound sources and sinks. A system model of tennis racket was developed from simultaneous measurement of excitation force, surface vibration and the near field sound pressure. The characteristics of structural dynamics were obtained by standard experimental modal analysis techniques while the sound radiation characteristics were determined by estimating the acoustic intensity. In this paper, the information about vibration behviour was obtained by acoustic intensity method and some, experiments for verification were carried out. Close correlation was found between experimentally determined acoustic intensity and vibration mode patterns of the tennis racket.