• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.11 no.5
• /
• pp.481-486
• /
• 2018

DC motors are classified as DC motors with brush structure and BLDC motors without brush structure. Representing the speed control of the BLDC motor is the PI control. The speed control using the PI controller has a disadvantage that the response characteristic to reach the steady state is slow. Therefore in this paper, a voltage controlled speed controller using a Fuzzy Logic Controller (FLC), which has a short steady response time and usefulness of nonlinear control. The validity and usefulness of the proposed fuzzy speed controller are verified by simulation through Simulink of MATLAB program. Experiments were performed on the PI controller and the proposed fuzzy speed controller in three cases with reference speeds of 500rpm, 800rpm, and 1500rpm. Experimental results show that the proposed fuzzy controller has more 30% improved steady state speed response than PI controller.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.19 no.4
• /
• pp.47-54
• /
• 2019

In the worldwide, The issue comes up which is the danger of car accidents from climate-change effects. We are considering about various types of speed limit signs for setting restricts to high-speed vehicles. South Korea has 4 seasons in the land. At Summer or Winter seasons have heavy rains and fogs or snow, In these seasons need to enforce speed limit laws or methods to prevent car collision. But South korea is using stationary speed limiters that is not enough to proof against rear-end car accidents in these climates. In this paper shows the necessity of independent LED speed limits display to reduce car accidents. And explaining the prototype model which is a combination of rain sensor and wiper systems. This model is independently changed the speed limits to 50%, 80%, 100% of standards by raindrops and snowflake. Also it is freely setting speed limits on each places anywhere it settled in. Visual effects of the model as being speed-down of vehicles helps to prevent rear-ending car accidents and traffic beforehand.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.9 no.1
• /
• pp.17-26
• /
• 2005

Both numerical analysis and cold tests for the swirl coaxial type injector were performed to obtain the influence of spray angle, velocity ratio and liquid film thickness for pressure drop and recess. The basic experimental and numerical data obtained in this study can be applicable to the performance design of swirl coaxial type injector. Spray angle was not affected by the applied test pressure drop, but spray angle was affected by tangential velocity ratio and shape factors. Feasibility of numerical analysis for the liquid film thickness and spray angle was confirmed, and the change of liquid film thickness by tangential velocity ratio affected more seriously than pressure drop, and liquid film thickness was decreased with increasing tangential velocity ratio.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.7 no.4
• /
• pp.375-382
• /
• 2019

In this study, an experimental study on the buildability of the structure using the developed printing materials and equipment was performed. Experimental variables included the moving speed of nozzles(=80 and 100mm/s), the revolutions per minute (RPM) of screw in discharge buckets, and the aspect ratio(=1.67 and 5.00) reflecting wall length of the structures. Buildability of the 3D printed concrete structures was analyzed based on the maximum decomposition layer and collapse patterns of the structures according to the experimental variables. The nozzle movement speed of 80mm/s and the aspect ratio of 1.67 were favorable for 3D printing in this study. The collapse process of structure due to uneven layer decomposition was also analyzed through the relative displacement measurement of the lower part of the structure during printing.

• Composites Research
• /
• v.20 no.6
• /
• pp.28-33
• /
• 2007

The puncture properties of short-fiber reinforced rubber were investigated as functions of fiber aspect ratio(AR: length of fiber/diameter of fiber), fiber content, specimen size and testing velocity. The puncture stresses of the matrix and short-fiber reinforced rubber decreased with specimen size, and increased with testing velocity at same specimen size. As the fiber AR increased the puncture stress at given fiber content also increased. The problem of the specimen shape was investigated by the comparison of the tensile strength with puncture stress. The forces acting in the membrane wall of the matrix and the short-fiber reinforced rubber showed a similar data regardless of specimen size. And those increased with testing velocity at same specimen size. As the fiber AR increased the force acting in the wall at given fiber content also increased. Overall, it was found that the specimen size, testing velocity had an important effects on the puncture properties.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.37 no.2
• /
• pp.119-131
• /
• 2024

Pulse-like ground motion can cause greater damage to structures than nonpulse-like ground motion. Currently, much research is being conducted to determine the presence or absence of velocity pulses and to quantify them from seismic-acceleration records. Existing ground motion is divided into far-field (FF) and near-fault ground motion, based on the distance of the measurement point from the fault. Near-fault ground motion is further classified into near-fault pulse-like (NFP) and near-fault nonpulse-like (NFNP) ground motion by quantifying the presence or absence of velocity pulses. For each ground motion group, 40 FF, 40 NFP, and 40 NFNP ground motions are selected; thus, 120 ground motions are used in the seismic analysis to assess the seismic fragility of sample bridges. Probabilistic seismic demand models (PSDMs) are created by evaluating the seismic responses of two types of sample bridges with lead-rubber and elastomeric rubber bearings using three groups of ground motions. Seismic fragility analysis is performed using the PSDM, and from these results, the effect of the presence or absence of seismic velocity pulses on the seismic fragility is evaluated. From the comparison results of the seismic fragility curve, the seismic fragility of NFP ground motion appears to be approximately three to five times greater than that of NFNP ground motion, according to the presence or absence of a velocity pulse of seismic waves. This means that the damage to the bridge is greater in the case of NFP ground motion than that in the case of NFNP ground motion.

• Proceeding of EDISON Challenge
• /
• 2016.03a
• /
• pp.598-603
• /
• 2016

현대의 스포츠는 과학기술의 발전과 함께 성장하고 있고 골프종목 역시 재료역학적, 공기역학적 발전에 따라 비거리를 점점 늘려가고 있다. 하지만 현재까지의 비거리에 대한 연구는 골프공과 골프채의 재료의 변화와 딤플이 있는 골프공의 공기역학적 연구에 집중해 있었고 요즘에 들어서야 클럽헤드의 공기역학적 형상에 대한 연구가 활발히 진행되고 있다. 본 연구에서는 골프 경기 중 가장 먼 비거리를 만들어 내는 골프채인 드라이버의 단순화된 2차원 클럽헤드 형상을 설정하고 항력을 줄일 여러 가지 방법을 적용하여 최소의 항력을 갖는 헤드 형상을 찾아보았다. 연구결과 $10.2^{\circ}$의 로프트를 갖는 클럽헤드는 chord 길이가 face 높이의 3.2배이고, trailing edge가 face의 중심보다 전체 face높이의 10% 아래에 있을 때 가장 적은 항력을 얻을 수 있었다. 결과적으로 이 형상과 기존형상의 스윙 속도 차는 약 2mph로 5yard의 비거리 차이를 가져온다.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.8 no.12
• /
• pp.1865-1874
• /
• 2013

In this paper, a design method of speed and position estimator based on unscented Kalman filter is proposed for the no sensor control of IPMSM(Interior Permanent Magnet Synchronous Motor). The proposed method is simple more than the estimator designed with rotation axis for current measurement. Also the proposed state estimator is designed including nonlinear terms of the estimator. The controller which constructed using nonlinear back-stepping control method is operated speed and current control using the estimated speed and currents information. Through simulation, the performance of the designed estimator is compared to the estimator which is designed to synchronize d-q axis.

• Proceedings of the KIEE Conference
• /
• 2000.07d
• /
• pp.3160-3162
• /
• 2000

변화 부호화는 기존에 부호화 되어있는 영상의 비트율을 더 낮은 비트율의 영상으로 재 부호화하거나. 다른 부호화 표준으로 재 부호화 하는 기법이다. 변환 부호화기의 설계에서 가장 중요시되는 문제는 화질 향상과 부호화 속도의 향상이다. 변환 부호화기의 많은 응용분야에서 실시간 변환을 필요로 하기 때문에 변환 속도를 향상시키면서 화질을 높이는 방법이 연구되어 왔다. 비트율 변환비가 매우 클 때에나 표준화 방법의 목적 영상 사이즈가 다를 때엔 비트율의 변환과 함께 영상의 크기를 함께 변환(1/2)해 주어야할 필요가 있다. 본 논문에서는 이러한 경우에 적합한 변환 부호화기법을 제안한다. 우선 영상의 크기를 다운스케일링 해 준후, 기존 영상의 움직임 벡터들로부터 AWW기법을 이용해 1차 추정 벡터를 추출하여 속도를 향상시키고, 1차 추출 벡터 부근의 한정된 영역으로부터 움직임 벡터 추정과정을 거쳐 최종 추정 벡터를 정제하여 화질을 향상시킨다. 실험 결과 기존의 재 부호화 기법에 비해 속도가 향상됨을 확인 할 수 있었으며. AWW 기법에 비해 연산량은 조금 많아지나 정제 과정을 통하여 약 1dB 정도의 화질 향상이 있음을 확인할 수 있었다.

• Journal of the Institute of Convergence Signal Processing
• /
• v.4 no.3
• /
• pp.55-60
• /
• 2003

In the controller design of position or velocity control system, the flexibility of the mechanical system is always the limiting factor to the higher performance. Most mechanical systems coupled with rotary shaft are 2-Inertia systems which are consist of motor and load inertia. These inertias make a torsion In rotary shaft and cause torsional vibration. To suppress vibration, various control strategies have been proposed mainly for controlling 2-inertia system. In this paper, a speed controller design for a 2-inertia system composed of voltage controlled DC motor and load inertia is made by using CDM(coefficient diagram method). First, the 2-inertia system model is derived. Then the CDM is used to design the proper controller. A validity of this approach is confirmed by simulation and experimental results.