• 전기전자학회논문지
• /
• 제22권1호
• /
• pp.223-226
• /
• 2018

최근 차량 사고로부터 탑승자를 보호하기 위해서 다양한 안전 기술이 집중적으로 개발되고 있다. 본 논문에서는 잠김 방지 브레이크 시스템, 견인력 제어 시스템, 제동력 배분 시스템, 전자 주행 안정 장치, 자동 긴급 브레이크, 에어백, 좌석벨트 프리텐셔너, 능동형 헤드레스트 등 다양한 차량용 탑승자 보호 기술을 살펴보고, 각 기술의 동작원리 및 구현에 대해 설명한다.

• 드라이브 ㆍ 컨트롤
• /
• 제16권1호
• /
• pp.22-28
• /
• 2019

This paper develops ABS braking real - time simulator to develop vehicle braking system by simulation. Recently, real-time simulation is widely used in the development of vehicles to decrease development time. In the field of electronic braking, real-time simulation is actively underway. In order to simulate electronic braking model in real time, a vehicle model, a hydraulic model, and a control S/W model are required. These models must be calculated in one platform. Therefore, in this paper, a vehicle model composed of CarSim and a hydraulic model composed of SimulationX using S/W in actual ABS controller was developed as a Simulink model base and linked with Matlab real time model. Using this real-time model, design effects of the electronic braking controller were simulated according to road surface condition to verify its operability.

• 대한기계학회논문집A
• /
• 제26권12호
• /
• pp.2519-2526
• /
• 2002

A disturbance observer-based vehicle stability controller is proposed in this paper. The lumped disturbance to the vehicle yaw rate dynamics caused by the uncertain factors such as uncertain tire forces and parameters is estimated by the disturbance observer, which is utilized by the robust controller to stabilize the lateral dynamics of the vehicle. The dynamics of the hydraulic actuator is incorporated in the vehicle stability controller design using the model reduction technique. Modular control design methodology is adopted to effectively deal with the mismatched uncertainty. Simulation results indicate that the proposed disturbance observer-based vehicle stability controller can achieve the desired reference tracking performance as well as sufficient level of robustness.

• 제어로봇시스템학회논문지
• /
• 제11권6호
• /
• pp.502-509
• /
• 2005

In this paper, a 4-wheel vehicle model including the effects of tire slip was considered, along with variable parameter sliding control, in order to improve the performance of the vehicle longitudinal response. The variable sliding parameter is made to be proportional to the square root of the pressure derivative at the wheel, in order to compensate for large pressure changes in the brake cylinder. A typical tire force-relative slip curve for dry road conditions was used to generate an analytical tire force-relative slip function, and an antilock sliding control process based on the analytical tire force-relative slip function was used. A retrofitted brake system, with the pushrod force as the end control parameter, was employed, and an average decay function was used to suppress the simulation oscillations. The simulation results indicate that the velocity and spacing errors were slightly larger than those obtained when the wheel slip effect was not considered, that the spacing errors of the lead and follower were insensitive to the adhesion coefficient up to the critical wheel slip value, and that the limit for the antilock control under non-constant adhesion road conditions was determined by the minimum value of the equivalent adhesion coefficient.

• 한국군사과학기술학회지
• /
• 제20권5호
• /
• pp.597-607
• /
• 2017

The general control method for Anti-lock Brake System(ABS) is that the wheel slip ratio is observed and the braking force is controlled in real time in order to keep the wheel slip ratio under the value of the best slip ratio. When a wheel runs on the state of the best slip ratio, the ground friction of the wheel approaches the highest value. The value of best slip ratio, theoretically, is known as the value between 10 and 20 % and it is dependant on the ground condition such as dry, wet and ice. It is an important parameter for the braking performance and affects the braking stability and efficiency. In this thesis, an experimental method is suggested, which is a reliable way to decide the best slip ratio through dynamo tests simulating aircraft taxiing conditions. The obtained best slip ratio is proved its validity by results of aircraft taxiing tests.

• 한국자동차공학회논문집
• /
• 제24권5호
• /
• pp.581-587
• /
• 2016

Braking is a basic and an important safety feature for all vehicles, and the final braking performance of a vehicle is determined by the vehicle's ABS performance and tire performance. However, the combination of excellent ABS and tires will not always ensure good braking performance. This is due to the fact that tire performance has non-linearity and uncertainty in predicting the repeated increase and decrease of wheel slip when activating the ABS, thus increasing the uncertainty of tire performance prediction. Furthermore, existing studies predicted braking performance after using an ABS that used a wheel slip control as a controller, which was different from an actual vehicle's ABS that controlled angular acceleration, therefore causing a decrease in the prediction accuracy of the braking performance. This paper reverse-designed the ABS that controlled angular acceleration based on the information on brake pressure, etc., which were obtained from vehicle tests, and established a braking performance prediction analysis model by combining a multi-body dynamics(MBD) vehicle model and a magic formula(MF) tire model. The established analysis model was verified after comparing it with the results of the braking tests of an actual vehicle. Using this analysis model, this study analyzed the braking effect by vehicle factor, and finally designed a tire that had optimized braking performance. As a result of this study, it was possible to design the MF tire model whose braking performance improved by 9.2 %.