• Proceedings of the KIEE Conference
• /
• 1994.07a
• /
• pp.585-587
• /
• 1994

The chattering phenominon is the one of the problems on Variable Structure Controller(VSC). To alleviate this problem, Modified Variable Structure Controller(MVSC) with sliding sector is presented in this paper. This controller is adopted to the position drive system of brushless dc motor. For the simplification of hardware, the current controller also uses the sliding mode control method. Computer simulations are presented to show chattering alleviation of the proposed control scheme.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.5 no.3
• /
• pp.54-63
• /
• 1991

This paper describes an effort to develope a microcomputer-based parameter measurement system for a brushless DC motor. Back EMF equation is derived from back EMF waveform of a brushless DC motor. To minimize error the due to the ripple component in the measured armature current, digital averaging filter is employed. The whole identification process of signal generation, measurement parameter determination is fully automated. A new identification algorithm for the brushless DC motor parameters is developed. New parameter correction method is proposed using the deadzone current and the time to reach the peak current. In the proposed correction method, the measured current is in excellent agreement with the estimated current.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.11
• /
• pp.1894-1899
• /
• 2016

In this paper, because the position sensor represents the important factor in BLDC (Brushless DC) motor drives, BLDC motor is necessary that the three Hall-sensors evenly be distributed around the stator circumference in case of the 3 phase motor. The Hall-sensor is set up in this motor to detect the main flux from the rotor. So the output signal from Hall-sensor is used to drive IGBT to control the stator winding current. However, in case of breakdown Hall sensor, we research that the estimation algorithm of Hall sensor signal to detect rotor position and for the speed feedback signals with BLDC motor whose six stator and two rotor designed. In addition, this paper presents a sensorless speed control of BLDC Motor using terminal voltage of the one phase. Rotor position information is extracted by indirectly sensing the back EMF from only one of the three terminal voltages for a three-phase BLDC motor.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.26 no.8
• /
• pp.71-78
• /
• 2012

Recently, it is increased to apply sensorless drive for BLDC (Brushless DC) motor to maximize operating efficiency and fuel efficiency to an electrical component of (H)EV. Especially, Electric vehicle component promotes a fuel efficiency enhancement by the carbon dioxide emissions regulation of a vehicle becoming the principal of the environmental pollution globally, the oil price hike that continued increasingly. We suggested the air compressor which applied BLDC motor for electric vehicle component and compared suggested BLDC motor with the conventional DC motor. The experimental results show that the driving efficiency was increased and was inproved compressive force by suggested BLDC motor.

• Proceedings of the KIEE Conference
• /
• 1987.07b
• /
• pp.1317-1321
• /
• 1987

A new type of motor-driven Total Artificial Heart(TAH) system with rolling cylinder mechanism has been developed. Brushless DC motor was chosen as energy converter and controlled by PI controller according to the given velocity profile under the highly time-varying load. Computer simulation was also performed to calculate the optimal gains of PI controller which minimize the input power, one of the most important parameter in artificial heart system.

• 제어로봇시스템학회:학술대회논문집
• /
• 1988.10a
• /
• pp.706-710
• /
• 1988

Using back electro-motive force(EMF) signals of a brushless DC motor, the sensorless micro-processor controlled drive system was developed. In this new commutation method, the manual pulses are used for relatively short accelerating phase and then the exact commutational positions are detected based upon the back emf signals. The hardware and software implementations with the experiment to compare the performance of the developed system with the, conventional system using hall effect sensors are included. By reducing the number of the required sensors in the artificial heart control system, the total reliability will be incresed.

• Proceedings of the IEEK Conference
• /
• 1999.06a
• /
• pp.805-808
• /
• 1999

In this paper, a chattering alleviation ISM speed controller for the sinusoidal type BIDC motor is designed. Dead Zone function is proposed to change the chattering occurring in the transient state form high frequency to low frequency and time-varying gains are applied for the control input to eliminate the steady state excessive chattering in the conventional ISM. The proposed Dead Zone function represents the sliding layer composed of two switching surfaces and if a state vector exists in this layer, the chattering don’t occur. Simulation and experimental results confirm the useful effects of the above algorithm.

• Proceedings of the KIPE Conference
• /
• 2002.07a
• /
• pp.443-446
• /
• 2002

Brushless DC motor(BLDCM) are suitable to operate in a wide speed range, easy to control and since there are no mechanical brushes and commutators, require low maintenance costs and are free from restrictions of application environment. And since the ratio of instantaneous torque and rated torque is high, BLDCM are appropriate for variable speed operation. This paper proposes the optimal model by using Matlab/simulink based on modelling and characteristic analysis of trapezoidal back EMF type BLDCM and verifies the validity of the proposed model by applying control systems.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.55 no.8
• /
• pp.363-368
• /
• 2006

This paper presents a new method on reducing commutation torque ripples generated in brushless dc motor drives. In such drives the current ripples are generated by motor inductance in stator windings and the back EMF. The ripples suppression techniques that are practically effective in high speed as well as in low speed regions are rarely found. The proposed method here is based on a strategy that the commutation intervals of the incoming ang the outgoing phases can be equalized by a proper PWM control. The controller is implemented by a 16-bit microprocessor and effectiveness of the proposed control method is verified through experiments.

• Proceedings of the KIEE Conference
• /
• 1999.07a
• /
• pp.379-381
• /
• 1999

This paper presents a study of the performance of a brushless DC motor (BLDCM) speed control system. Recently, most motor controls are implemented in digital electronics. Digital controllers tend to be more accurate, less susceptible to noise and more flexible in terms of programming. The system used a digital PI controller in order to implement the constant speed of Brushless DC motor. Microprocessor used in this experiment is 80c196kc. The applied motor has been constructed using a 50W, 150V, 3000rpm, four-pole motor.