• Title/Summary/Keyword: 분사입자

Search Result 286, Processing Time 0.034 seconds

원심압축기에서 물분사 압축과정에 대한 이론적 해석

  • Kang, Jeong-Seek;Cha, Bong-Jun;Yang, Soo-Seok
    • Aerospace Engineering and Technology
    • /
    • v.4 no.1
    • /
    • pp.18-24
    • /
    • 2005
  • Wet compression means the injection of water droplets into the compressor of gas turbines. This method decreases the compression work and increases the turbine output by decreasing the compressor exit temperature through the evaporation of water droplets inside the compressor. This paper provides thermodynamic and aerodynamic analysis on wet compression in a centrifugal compressor for a microturbine. The meanline performance analysis of centrifugal compressor is coupled with the thermodynamic equation of wet compression to get the meanline performance of wet compression. The most influencing parameter in the analysis is the evaporative rate of water droplets. It is found that the impeller exit flow temperature and compression work decreases as the evaporative rate increases. And the exit flow angle decreases as the evaporative rate increases.

  • PDF

The Combustion and Emission Characteristics with Increased Fuel Injection Pressure in a Gasoline Direct Injection Engine (가솔린 직접 분사식 엔진에서 연료 분사 압력 증가에 따른 연소 및 배기 배출물 특성)

  • Lee, Junsun;Lee, Yonggyu
    • Journal of ILASS-Korea
    • /
    • v.22 no.1
    • /
    • pp.1-7
    • /
    • 2017
  • Recently, Performance and fuel efficiency of gasoline engines have been improved by adopting direct injection (DI) system instead of port fuel injection (PFI) system. However, injecting gasoline fuel directly into the cylinder significantly reduces the time available for mixing and evaporation. Consequently, particulate matters(PM) emissions increase. Moreover, as the emission regulations are getting more stringent, not only the mass but also the total number of PM should be reduced to satisfy the Euro VI regulations. Increasing the fuel injection pressure is one of the methods to meet this challenge. In this study, the effects of increased fuel injection pressures on combustion and emission characteristics were experimentally examined at several part load conditions in a 1.6 liter commercial gasoline direct injection engine. The main combustion durations decreased about $2{\sim}3^{\circ}$ in crank angle base by increasing the fuel injection pressure due to enhanced air-fuel mixing characteristics. The exhaust emissions and number concentration distributions of PM with particle sizes were also compared. Due to enhanced combustion characteristics, THC emissions decreased, whereas NOx emissions increased. Also, the number concentrations of PM, larger than 10 nm, also significantly decreased.

Influence of airborne-particle abrasion on flexural strength of fiber-reinforced composite post (미세입자 분사마모 표면처리가 Fiber-Reinforced Composite 포스트의 굴곡 강도에 미치는 영향)

  • Sim, Eun-Ju;Kim, Jin-Woo;Cho, Kyung-Mo;Park, Se-Hee
    • Journal of Dental Rehabilitation and Applied Science
    • /
    • v.32 no.1
    • /
    • pp.24-31
    • /
    • 2016
  • Purpose: Many studies have shown that airborne-particle abrasion of fiber post can improve the bonding strength to resin cement. But, airborne-particle abrasion may influence the property of fiber post. The purpose of this study is to evaluate the influence of airborne-particle abrasion on flexural strength of fiber post. Materials and Methods: Two fiber-reinforced posts; DT Light Post Size 2 (1.8 mm diameter, Bisco Inc) and RelyX Fiber Post Size 3 (1.9 mm diameter, 3M ESPE); were used in this study. Each group was divided into 3 subgroups according to different surface treatments; without pretreatment: $50{\mu}m$ aluminum oxide (Cobra$^{(R)}$, Renfert): and $30{\mu}m$ aluminum oxide modified with silica (Rocatec Soft$^{(R)}$, 3M ESPE). After airborne-particle abrasion procedure, three-point bending test was done to determine the flexural strength and flexural modulus. The diameter of each posts was measured to an accuracy of 0.01 mm using a digital micrometer. There was no diameter change before and after airborneparticle abrasion. The mean flexural moduli and flexural strengths calculated using the appropriate equations. The results were statistically analyzed using One-way ANOVA and Scheffe's post-hoc test at 95% confidencial level. Results: There was no significant difference on flexural strength between groups. Conclusion: In the limitation of this study, flexural strength and flexural modulus of fiber post are not affected by airborne-particle abrasion.

친환경 평판 디스플레이 세정을 위한 $CO_2$ Snow Jet 세정공정 개발에 관한 연구

  • Jeong, Ji-Hyeon;Gang, Bong-Gyun;Kim, Min-Su;Lee, Jong-Myeong;Lee, Gyu-Pil;Park, Jin-Gu
    • Proceedings of the Materials Research Society of Korea Conference
    • /
    • 2011.05a
    • /
    • pp.66.1-66.1
    • /
    • 2011
  • 반도체를 비롯하여 LCD, OLED와 같은 디스플레이 (FPD: Flat Panel Display) 분야는 국가 선도 사업으로써 발전을 거듭해오고 있다. 하지만 기술의 성숙도가 높아짐에 따라 최근 중국과 대만 업체와의 경쟁이 심화되고 있으며, 더불어 환경문제가 큰 이슈로 떠오르고 있어 신기술 개발을 통한 생산 수율 향상 및 친환경 공정 개발의 중요성이 커지고 있다. 반도체, 디스플레이 공정에서 생산 수율 저하의 주요 원인으로써 공정 중 발생하는 미세 오염 입자를 들수 있다. 반도체 및 디스플레이 공정에서 세정 기술은 전체 기술의 30% 이상을 차지하며 생산 수율 및 제품의 품질에도 큰 영향을 주는 공정이다. 세정 공정은 일반적으로 습식 세정 공정이 낮은 공정비용을 바탕으로 널리 적용되어 왔으나, 기판의 대형화와 패턴의 미세화에 따라 정밀한 세정 스펙이 요구되며 더불어 막대한 양의 초순수와 화학액의 사용으로 인한 공정비용 증가와 환경 규제 강화에 따른 폐수 처리의 문제에 직면하고 있다. 이에 따라 폐수의 양을 줄이며 건조공정을 필요로 하지 않아 공정비용을 줄일 수 있는 건식 세정 공정에 대한 연구가 활발히 진행 되고 있다. $CO_2$ snow jet 세정 기술은 건식 공정으로써 $CO_2$ 가스를 특수하게 제작된 분사 노즐에서 고압으로 가스를 분사하여 이 때 발생되는 순간적인 감압에 의한 단열 팽창으로 생성된 $CO_2$ snow 입자가 기판 표면의 오염물과 물리적 충돌을 하어 세정이 이루어지는 기술이다. 특히 $CO_2$ 세정은 환경과 인체에 무해하며 공정 후 바로 승화하기 때문에 추가적인 폐수처리 공정 등이 필요하지 않고, 건식 공정으로써 수세(Rinse) 공정을 필요로 하지 않기 때문에, 공정비용을 크게 줄일 수 있으며 물반점 발생을 방지 할 수 있는 친환경 건식 공정으로써의 장점을 가지고 있다. 본 연구에서는 자체적으로 개발한 $CO_2$ snow jet을 바탕으로 하여 다양한 공정조건을 변화시켜 세정효율을 측정하는 한편, 최적화 하기 위한 연구를 진행하였으며 더불어 $CO_2$ snow의 세정력을 정량적으로 평가하기 위한 연구를 진행하였다. 실험을 통해 가장 효과적으로 $CO_2$ snow 입자를 배출 할 수 있는 공정 조건으로써 5 bar의 캐리어 가스 압력을 사용하여, 세정력에 가장 큰 영향을 줄 수 있는 분사 노즐과 기판 사이의 거리 및 분사 노즐의 각도 등을 변화시켜 각 조건에 따른 세정효율을 평가하였다. 세정 오염물은 Silica, PSL 표준 입자(Duke scientific, USA)를 정량적으로 웨이퍼에 오염 시킨 후, 파티클 스캐너(Surfscan 6500, KLA-Tencor, USA)를 이용하여 세정 전 후의 오염입자 개수 변화를 통해 정량적으로 세정효율을 평가하였다. 본 연구를 통하여 $CO_2$ snow jet를 이용한 친환경 고효율 건식 세정 공정 메커니즘을 분석하였으며, 노즐과 기판 사이의 간격 및 분사 노즐의 각도 등을 최적화 한 세정 공정을 얻을 수 있었다.

  • PDF

20wt% $\textrm{Y}_{2}\textrm{O}_{3}$-$\textrm{ZrO}_{2}$ Powder Spraying by Induction Plasma (유도플라즈마에 의한 20wt% $\textrm{Y}_{2}\textrm{O}_{3}$-$\textrm{ZrO}_{2}$분말의 용융분사)

  • Jeong, In-Ha;Bae, Gi-Gwang
    • Korean Journal of Materials Research
    • /
    • v.8 no.8
    • /
    • pp.699-706
    • /
    • 1998
  • 현재까지 박막코팅 분야에 주로 이용해 오던 플라즈마 용융분사법을 이용하여 고밀도의 두꺼운 세라믹 침적물을 제조하였다. 용융점이 2910K인 ZrO2-20wt%Y2O3분말을 이용하여 최적조건에서 이론밀도의 약 97%의 침적물을 얻었다. 고밀도 침적에 영향을 미치는 변수는 챔버 내부압력, 플라즈마동력, 플라즈마 가스조성, 분사거리, 분말입자 크기 등이었으며, 침적밀도 및 침적된 splat의 형태는 분말의 용융정도 및 챔버 내부압력에 크게 좌우되었다. 높은 밀도으 침적물을 만들기 위해서는 분말을 완전히 용융시키는 것이 중요하며, 완전히 용융된 조건에서는 챔버 내부압력이 낮고 분말분사거리가 짧은 조건 즉, 분사되는 분말이 높은 모멘텀을 가질수록 침적물의 밀도가 증가함을 알 수 있었다. 실험에서 얻어진 결과는 ANOVA 통계방법으로 분석하여 단일변수의 영향뿐만 아니라 이들 변수가 서로 조합하여 밀도에 미치는 영향도 분석하였다.

  • PDF

Fast Pyrolysis Characteristics of Jatropha Curcas L. Seed Cake with Respect to Cone Angle of Spouted Bed Reactor (분사층 반응기의 원뿔각에 따른 Jatropha Curcas L. Seed Cake의 급속열분해 특성)

  • Park, Hoon Chae;Lee, Byeong-Kyu;Kim, Hyo Sung;Choi, Hang Seok
    • Clean Technology
    • /
    • v.25 no.2
    • /
    • pp.161-167
    • /
    • 2019
  • Several types of reactors have been used during the past decade to perform fast pyrolysis of biomass. Among the developed fast pyrolysis reactors, fluidized bed reactors have been widely used in the fast pyrolysis process. In recent years, experimental studies have been conducted on the characteristics of biomass fast pyrolysis in a spouted bed reactor. The fluidization characteristics of a spouted bed reactor are influenced by particle properties, fluid jet velocity, and the structure of the core and annulus. The geometry of the spouted bed reactor is the main factor determining the structure of the core and annulus. Accordingly, to optimize the design of a spouted bed reactor, it is necessary to study the pyrolysis characteristics of biomass. However, no detailed investigations have been made of the fast pyrolysis characteristics of biomass in accordance with the geometry of the spouted bed reactor. In this study, fast pyrolysis experiments using Jatropha curcas L. seed shell cake were conducted in a conical spouted bed reactor to study the effects of reaction temperature and reactor cone angle on the product yield and pyrolysis oil quality. The highest energy yield of pyrolysis oil obtained was 63.9% with a reaction temperature of $450^{\circ}C$ and reactor cone angle of $44^{\circ}$. The results showed that the reaction temperature and reactor cone angle affected the quality of the pyrolysis oil.

The Effect of Temporary Cement Cleaning Methods on the Retentive Strength of Cementation Type Implant Prostheses (임시 시멘트 제거방법이 시멘트 유지형 임플란트 보철물의 유지력에 미치는 영향)

  • Shin, Hwang-Kyu;Song, Young-Gyun;Shin, Soo-Yeon
    • Journal of Dental Rehabilitation and Applied Science
    • /
    • v.27 no.2
    • /
    • pp.125-140
    • /
    • 2011
  • The remnant of temporary cement on the intaglio surface of cast restoration may have a negative effect on the retentive strength of permanent cement. This study was to evaluate the effect of temporary cement cleaning methods on the retentive strength of cementation type implant prostheses. Prefabricated implant abutments - height 5.5mm, diameter 4.5mm, 6 degree axial wall taper with chamfer margins were used. Forty copings-abutment specimens were divided into four groups(each n=10) according to the cleaning methods for temporary cement(Temp-$Bond^{(R)}$) as follows : no temporary cementation(the control group), orange solvent, ultrasonic cleaning, air borne-particle abrasion. After the application of temporary cement and the separation, the cleaning procedure was performed according to the protocol of each group. The specimens were cemented with $Premier^{(R)}$ Implant $Cement^{TM}$. After the permanent cementation, the specimens were subjected to thermocycling and pulled out from the specimens with a universal testing machine at a cross-head speed of 0.5mm/min. After the retentive strength test, all the specimens were cleaned using ultrasonic cleaning, abraded with air borne-particles, and steam-cleaned. Likewise, the specimens were temporarily cemented(Temp-$Bond^{(R)}$ NE), cleaned according to the protocol of each group, cemented with $Premier^{(R)}$ Implant $Cement^{TM}$ and subjected to thermocycling and measurement of their retentive strength. The mean of group with orange solvent were significantly lower than those of other groups(p<0.05). There was no significance between group with ultrasonic cleaning and group with air borne-particle abrasion. Group with ultrasonic cleaning and group with air-particle abrasion were no significance at control group. There was no significance between group cemented with Temp-$Bond^{(R)}$ and group cemented with Temp-$Bond^{(R)}$ NE. Within the limitation of this study, it can be concluded that the temporary cement cleaning method with only orange solvent may have a negative effect on the retentive strength of permanent cement. Ultrasonic cleaning and air borne-particle abrasion methods are recommended for the temporary cement cleaning method on cementation type implant prostheses.

Measurements of Diesel Particle Size Distribution Using an ELPI (ELPI를 이용한 디젤 입자상물질의 입경 분포 측정)

  • 김홍석;조규백;정용일;이상수;성낙원
    • Proceedings of the Korea Air Pollution Research Association Conference
    • /
    • 2003.11a
    • /
    • pp.75-76
    • /
    • 2003
  • 본 연구는 ELPI(Electrical Low Pressure Impactor)를 이용하여 소형디젤기관에서 배출되는 입자상물질의 입경분포를 측정하였으며, 희석공기온도, 희석비, 측정위치가 측정에 미치는 영향을 고찰하였다. 본 연구에서는 배기량이 3000 cc인 간접분사식 소형디젤기관에서 발생하는 입자상물질의 입경분포를 고찰하고자 Dekati사의 ELPI를 사용하였다. 다단임팩터의 오염을 막기위해 ejector 형식의 2단 희석장치를 사용하였다.(중략)

  • PDF

$CO_2$ 클러스터 세정을 이용한 오염입자 제거에 관한 연구

  • Choe, Hu-Mi;Jo, Yu-Jin;Lee, Jong-U;Kim, Tae-Seong
    • Proceedings of the Korean Vacuum Society Conference
    • /
    • 2013.02a
    • /
    • pp.482-482
    • /
    • 2013
  • 반도체 소자의 미세화와 더불어 세정공정의 중요성이 차지하는 비중이 점점 커지고, 이에 따라 세정 기술 개발에 대한 요구가 증대되고 있다. 기존 세정 기술은 화학약품 위주의 습식 세정 방식으로 표면 손상, 화학 반응, 부산물, 세정 효율 등 여러 가지 어려움이 있다. 따라서 건식세정 방식이 활발하게 도입되고 있으며 대표적인 것이 에어로졸 세정이다. 에어로졸 세정은 기체상의 작동기체를 이용하여 에어로졸을 형성하고 표면 오염물질과 직접 물리적 충돌을 함으로써 세정한다. 하지만 이 또한 생성되는 에어로졸 내 발생 입자로 인해 패턴 손상이 발생하며 이러한 문제점을 극복하기 위하여 본 연구에서는 가스클러스터 장치를 이용한 세정 특성 평가에 관한 연구를 수행하였다. 가스 클러스터란 작동기체의 분자가 수십에서 수백 개 뭉쳐 있는 형태를 뜻하며 이렇게 형성된 클러스터는 수 nm 크기를 형성하게 된다. 그리고 짧은 시간의 응축에 의해 수십 nm 크기까지 성장하게 된다. 에어로졸 세정과 다르게 클러스터가 성장할 환경과 시간을 형성하지 않음으로써 작은 클러스터를 형성하게 되며 이로 인해 패턴 손상을 최소화 하고 상대적으로 높은 효율로 오염입자를 제거하게 된다. 클러스터 세정 장비를 이용한 표면 처리는 충돌에 의한 제거에 기반한다. 따라서 생성 및 가속되는 클러스터로부터 대상으로 전달되는 운동량의 정도가 세정 특성에 영향을 미치며 이는 생성되는 클러스터의 크기에 종속적이다. 생성 클러스터의 크기 분포는 분사 거리, 유량, 분사 각도, 노즐 냉각 온도 등의 변수에 관한 함수이다. 따라서 본 연구에서는 $CO_2$ 클러스터를 이용한 세정 특성을 평가하기 위하여 이러한 변수에 따라서 오염 입자의 종류, 크기에 따른 PRE (particle removal efficiency)를 평가하고 다양한 선폭의 패턴을 이용하여 손상 실험을 수행하였다. 제거 효율에 사용된 입자는 $CeO_2$$SiO_2$이며, 각각 30, 50, 100, 300 nm 크기를 정량적으로 오염시킨 쿠폰 웨이퍼를 제조하여 세정 효율을 평가하였다. 정량적 오염에는 SMPS (scanning mobility particle sizer)를 이용한 크기 분류와 정전기적 입자 부착 시스템이 사용되었다. 또한 패턴 붕괴 평가에는 35~180 nm 선폭을 가지는 Poly-Si 패턴을 이용하였다. 실험 결과 클러스터 형성 조건에 따라 상대적으로 낮은 패턴 붕괴에서 95% 이상의 높은 오염입자 제거효율을 전반적으로 보이는 것을 확인할 수 있었다. 따라서 이론적 계산에 기반하여 세정에 요구되는 클러스터 크기를 가정하고, 이를 통하여 세정에 적용할 경우 높은 기존 세정 방법의 단점을 보완하면서 높은 세정 효율을 가지는 대체 세정 방안으로 이용할 수 있음을 확인하였다.

  • PDF