• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.2D
• /
• pp.285-292
• /
• 2006

The objective of this study is to introduce the development of the first Korean full-scale APT(Accelerated Pavement Tester) and to compare the performances of general dense grade asphalt mixture and modified asphalt mixtures as the first running of the tester. The tests evaluated the rutting resistance for dense grade mixture and three different modified asphalt mixture under three different temperature conditions (25-30, 40, $50^{\circ}C$). The results of the testing were compared with the laboratory test results. Results of the tests indicated that the all the modified asphalt sections showed higher rutting resistance than the dense grade section. Especially, the difference was more noticeable at higher temperature condition. Additionally, $G^*/sin{\delta}$ is found out to be an important factor for permanent deformation prediction whereas the resilient modulus was not.

• Journal of the Korean Geotechnical Society
• /
• v.24 no.12
• /
• pp.53-63
• /
• 2008

In this study, the cone tip resistances of cemented sand are measured by performing a series of miniature cone penetration tests in large calibration chamber, and the relations with constrained modulus, unconfined compressive strength, and shear strength of cemented sand are suggested. Experimental results show that both the cone tip resistance and constrained modulus of sand increase with increasing cementation effect as well as relative density and confining stress. However, it is observed that the relative density and confining stress have more significant influence on cone tip resistance than constrained modulus of cemented sand. Since the cone penetration into the ground induces the damage of cementation, the cone tip resistance can't properly reflect the cementation effect of sand. An analysis based on the constrained modulus shows that the measured cone tip resistance underestimates the deformation modulus of cemented sand by about $70{\sim}85%$. In addition, this study establishes various relationships among the above soil properties from the regression analysis.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.11a
• /
• pp.35.1-35.1
• /
• 2009

오스테나이트계 Fe-10Cr-10Ni-xC(x=0.2, 0.5, 0.6and 0.7wt.%)합금에서 변형유기마르텐사이트상변태가 Sliding 마모저항성에 미치는영향을 탄소 및 온도에 따라 조사하였다. 변형유기마르텐사이트상변태가 미치는 영향을 살펴보기 위해 석출물적고 grain의 크기가 비슷한 합금내에서 조사하였다. 변형유기마르텐사이트상변태가 일어나는데 필요한 에너지를 변형률-응력 곡선을 통해 구할 수 있으며, 이를 임계변형에너지라 규명했다. 그 결과, 상온에서 Carbon 함량에 따라 변형유기마르텐사이트상변태가 일어나는데 필요한 임계변형에너지는 증가하였으며, Sliding 마모저항성은 저하되었다. 이는 carbon이 오스테나이트 안정화원소(austenite stabilityelement)이므로 carbon 함량이 증가할수록 변형유기마르텐사이트상변태가 유발하기위해서는 많은 에너지가 필요하기 때문에 low C에 비해 high C의 마모저항성이 저하된 것으로 사료된다. 또한 변형유기마르텐사이트상변태가 고온 Sliding 마모저항성에 미치는 영향을 살펴보기 위해 Fe-Cr-Ni-xC(x=0.2, 0.5, 0.6 and 0.7wt.%)합금을 온도별(25, 100, $300^{\circ}C$)로 조사하였다.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.6 no.4
• /
• pp.147-155
• /
• 2002

To find the safety and serviceability of bridges, it must consider the behaviour of structural member and evaluation of the exact resistance of the member subjected to external loads. To evaluate the behaviour and the resistance of the structural member, it must measure the strains and displacements of the structures. Usually we use the strain gauge to measure the strains. When, the bridge is long span and high pier, the setting of strain gauge is very difficult and not economic. It is not recommendable for the use of strain gauge, when the structural member has many cracks and moisture. Thus, to make up for this demerits, the algorithm of strain analysis by measured displacements data is proposed.

• International Journal of Highway Engineering
• /
• v.11 no.4
• /
• pp.25-31
• /
• 2009

In general, it is well known fact that the stone mastic asphalt (SMA) pavement has a high resistance against rutting. However, performance of SMA is not well measured by general method used in the laboratory. The objective of this study is to investigate an applicability of deformation strength ($S_D$) for performance estimation of SMA, and to find out the correlation between rut depth and dynamic stability, and $S_D$ of SMA. This study carried out wheel tracking test and Kim-test with optimum asphalt content (OAC) determined by mix design. The results indicated that the $S_D$ of SMA was very poorer than those of dense-graded asphalt mixtures. $S_D$ showed similar WT dynamic stability and rut-depth level. It was found that Kim-test was not reflected higher rutting resistance of SMA like as indirect tensile strength (ITS) test and Marshall stability test. Also, it was revealed that dynamic stability and rut-depth of WT had some problems to estimate rutting resistance of SMA mixtures.

• 기계와재료
• /
• v.23 no.3
• /
• pp.16-29
• /
• 2011

결정 합금 대비 비정질 합금은 높은 경도를 갖기 때문에 마모 저항성도 좋고 내부 식성 등 환경에 대한 저항성도 월등하며, 또한 과냉된 액상 상태까지 재가열하게 되면 낮은 점성도를 갖게 되므로 복잡한 3차원적인 형상을 가지는 부품을 환경에 대한 저항성, 피로 저항성, 강도 및 경도 등을 모두 고려하여 높은 정밀도를 가지고 제조하는 것이 가능하므로 우수한 물성을 갖는 구조 및 기능성 재료로의 다양한 응용이 타진되고 있다. 이러한 비정질 합금의 변형 거동에 대한 연구는 대부분 유리 천이 온도 이하에서의 전단 및 파단에 이르는 이른바 불균일 변형(Inhomogeneous Deformation) 거동에 대한 이해를 위한 실험 및 해석적 연구에 집중되어 왔다. 반면 상업화의 기반이 되는 고상 기반 2차 정형 성형은 과냉 액상 영역에서의 구조 완화 및 결정화롤 대표되는 미세 구조 제어 균일 변형(Homogeneous Deformation)에 대한 이해 없이는 불가능하므로, 이러한 관점에서 비정질 합금 특유의 점성 유동 특성을 이용한 균일 변형 응용 예시 및 미세구조 변화 연계 해석 기술의 현황을 소개하고자 한다.

• Journal of the Microelectronics and Packaging Society
• /
• v.24 no.3
• /
• pp.27-34
• /
• 2017

We investigated the feasibility of parylene F usage as an intermediate layer between a polydimethylsiloxane (PDMS) substrate and an Au thin-film interconnect as well as the swelling effect of PDMS substrate on the stretchable deformability of an Au thin film. The 150-nm-thick Au film, which was sputtered on a PDMS substrate without a parylene F layer, exhibited an initial resistance of $11.7{\Omega}$ and an overflow of its resistance at a tensile strain of 12.5%. On the other hand, the Au film, which was formed with a 150-nm-thick parylene F layer, revealed an much improved resistance characteristics: $1.21{\Omega}$ as its initial resistance and $246{\Omega}$ at its 30% elongation state. With swelling of PDMS substrate, the resistance of an Au film substantially decreased to $14.4{\Omega}$ at 30% tensile strain.

• The Journal of Engineering Geology
• /
• v.21 no.2
• /
• pp.117-124
• /
• 2011

Soil deformations such as settlement, heaving and lateral flow have frequently happened on marine reclaimed soft grounds due to embankment filling or banking. The electrical resistivity survey was applied to investigate on ground surface such soil deformation without disturbance of ground. A test embankment was performed to assess soil deformation in marine reclaimed soft grounds, where was located at Sihwa area in western coast of Korean peninsula. The soft ground was composed of clayey sediments. After embankment filling, the boundary of soil deformation affected by the filling could be investigated with application of the electrical resistivity survey. The result of electric resistivity survey shows that the extent of deformation is about 5 m laterally to the southern direction of embankment and about 5~6 m vertically in depth, which is about 1-1.2 times of embankment height. This shows that the electric resistivity survey can be applied to interpret the ground deformation in a soft ground region.

• Korean Journal of Materials Research
• /
• v.4 no.8
• /
• pp.945-951
• /
• 1994

In order to elucidate the extrusion characteristics of $SiC_{p}$/6061 Al composite, defomation resistance, $K_{w}$ was determined using the empirical formula suggested by Watanabe et al, and also extrusion pressure was measured using the extrusion press with a capacity of 350 ton. The $K_{w}$ which are propotional to extrudability, was increased with increasing volume fraction of reinforcement, $SiC_{p}$, but decreased with increasing the particle size. The peaks of maximum extrusion pressure in curves of extrusion force vs ram stroke were changed sharply with decreasing the particle size. The elevated extrustion temperature resulted in the decreased $K_{w}$ and extrusion pressure, but caused the surface tearing of extrusion composite bars. The results showed that extrudability of the composite billets is depend on the extrusion conditions as well as the characteristics of reinforcement, $SiC_{p}$.

• Journal of the Microelectronics and Packaging Society
• /
• v.24 no.3
• /
• pp.19-26
• /
• 2017

Stretchable deformation-resistance characteristics of Au, Pt, and Cu films were measured for the stretchable packaging structure where a parylene F was used as an intermediate layer between a PDMS substrate and a metal thin film. The 150 nm-thick Au and Pt films, sputtered on the parylene F-coated PDMS substrate, exhibited the initial resistances of $1.56{\Omega}$ and $5.53{\Omega}$, respectively. The resistance increase ratios at 30% tensile strain were measured as 7 and 18 for Au film and Pt film, respectively. The 150 nm-thick Cu film, sputtered on the parylene F-coated PDMS substrate, exhibited a very poor stretchability compared to Au and Pt films. Its resistance was initially $18.71{\Omega}$, rapidly increased with applying tensile deformation, and finally became open at 5% tensile strain.