• Journal of the Korean Society of Marine Environment & Safety
• /
• v.25 no.7
• /
• pp.953-960
• /
• 2019

The Miller cycle is a diesel engine that has been developed in recent years that it can reduce NOx and improve fuel consumption by reducing the compression ratio through intake valve closing (IVC) time control. The Miller cycle can be divided into the early Miller method of closing the intake valve before the bottom dead center (BDC) and the late Miller method of closing the intake valve after the BDC. At low speeds, the late Miller method is advantageous as it can increase the volumetric efficiency; while at medium and high speeds, the early Miller method is advantageous because of the high internal temperature reduction effect due to the expansion of the intake air during the piston lowering from IVC to BDC. Therefore, in consideration of the ef ects of the early and late Miller methods, it is necessary to adopt the most suitable Miller method for the operating conditions. In this study, a two-stage turbo charge system was applied to four-stroke engines and the process of enhancing the Miller effect through a reduction of the intake and exhaust valve overlap as well as the valve change adjustment mechanism were considered. As a result, the ef ects of fuel consumption and Tmax reduction were confirmed by adopting the Miller cycle with a two-stage supercharge, a reduction of valve overlap, and an increase of suction valve lift.

• Proceedings of the KIPE Conference
• /
• 2010.07a
• /
• pp.43-44
• /
• 2010

본 논문에서는 저전압 구동 인버터의 게이트 구동회로 설계 시, 밀러 캡 영향이 야기할 수 있는 암 단락 현상 방지를 위한 양전원 방식의 게이트 구동회로 설계를 제안한다. 제안하는 회로는 부트스트랩 방식의 0~15[V] 의 전원을 사용하고, 커패시터와 다이오드를 통하여 마이너스 전압을 생성하며 이를 통해 양전원으로 게이트를 구동한다. 이는 단 전원 방식에 비하여 밀러 캡의 영향을 줄일수 있고 이를 통해 스위칭 시 소자의 스트레스를 감소시키며 또한 암단락을 방지한다. 제안하는 회로를 시뮬레이션과 실험을 통해 검증하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.8
• /
• pp.1100-1106
• /
• 2009

Recently, there are quite a lot of attention is drown on the researches related to of Miller method applied high expansion cycle. For this study, high expansion cycles are formed and analyzed with the base view point of thermodynamics, and the features of each factors are also investigated. As a result of analysis, the expansion-compression ratio is expected with a decrease of effective compression ratio as intake valve closing time retarded, however, the decrease of mean effective pressure and its output is accompanied with the counterflow of intake air. Accordingly, as the consequence of such failure, it is expected that an alternative is needed for the realization of high expansion cycles, and the improvement over thermal efficiency. To materialize such cycle, the control system to delay the closing time of intake valve was designed and VVT, the 3 S/B low speed diesel engine, is applied to evaluate the efficiency. The result of the trial shows that there was no significant errors.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.9 no.3
• /
• pp.289-295
• /
• 1998

The purpose of this paper is to propose an improvement method of BER for coded 16-QAM under Rayleigh fading channel. To overcome the BER degradation due to the fading under mobile communication, we apply delay modulation technique which is efficient to get both a coding gain and approximately one-half those needed by Manchester coding on bandwidth requirements. Especially, the delay modulation scheme is insensitive to the $180^{\circ}$phase ambiquity common to NRZ-L and Manchester coding schemes. From the computer simulation, BER performance of our scheme has achieved about 3.8 dB improvement of about $10^{-4}$, compared to Manchester coded 16-QAM.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2014.10a
• /
• pp.299-301
• /
• 2014

본 논문에서는 직류 오프셋 (DC-offset) 제거 기능을 가진 저 전력 자동 이득 조절 증폭기 (PGA, Programmable Gain Amplifier)를 제안한다. 이러한 회로는 직류 오프셋 문제점을 해결하기 위해 기존의 gm-boosting 증폭기를 변형한 디지털 이득 제어 방식으로 설계되어 있기 때문에 우수한 선형성을 가진다. 또한 특수 목적에 맞도록 그 이득을 6dB에서 60dB까지 7단계로 조절 가능하며, 밀러효과를 이용한 AC-coupling 방식으로 큰 값의 유동적인 커패시터와 저항을 구현하여 직류 오프셋을 제거한다. 제안한 PGA는 기존 회로에 비해 0.2dB 보다 작은 이득오차와 0.47mW의 낮은 소비전력 특성을 보였다.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.10
• /
• pp.1107-1113
• /
• 2009

In this paper, the design and implementation of K-Band frequency dividers using 130 nm CMOS process are presented. A Miller frequency divider is presented, which realizes a division range from 20 to 25 GHz with 7.2 mW power consumption from 1.2 V supply. The layout size of the core circuit is about $315{\times}246\;um^2$. In addition, a CML frequency divider which divides the output signal of the Miller frequency divider is also presented, which realizes a division range from 8.5 to 13 GHz with 5.7 mW power consumption. The layout size of the CML core is about $91{\times}98\;um^2$. Cascading the Miller and CML frequency dividers, we confirmed the divide-by-4 operation for the input signal from 20 to 25 GHz.

• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.6
• /
• pp.835-842
• /
• 2009

The present thesis carried out a research on a compression pressure's reduction phenomenon and its countermeasure according to the thermal efficiency improvement method by a Miller method in 4-cycle low speed diesel engine. In case of retardation of intake valve closing time in a engine, the theoretical heat efficiency shows a remarkably reducing trend when a compression ratio is not compensated. Accordingly, the thermal efficiency showed an increasing trend in case of compensating the compression ratio. Especially, it could be understood that the theoretical heat efficiency at near ABDC $100^{\circ}$ of intake valve closing time in case of compensation of the compression ratio was improved by around 25.1%, and the mean effective pressure was also increased by around 18.6%. Also, as the retardation of intake valve closing time increases, air quantity becomes insufficient due to a backflow phenomenon of intake air and thus thermal efficiency was decreased in a high load operation domain. The solving method of this problem is possible by supercharge. Therefore, in order to improve thermal efficiency by retardation of ntake valve closing time, the thermal efficiency improvement according to low compression is possible when there are a compensation device of a compression ratio and a supercharge device. This is a problem-solving method of low compression and high expansion cycle.

• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.2
• /
• pp.230-237
• /
• 2012

Engine makers are lately interested in the gas engine development as the alternative for diesel engine in order to cope the rise of oil price and the environmental regulation. So, STX has developed the 1.6MW gas engine which was converted from 22HLX diesel engine. The gas engine developed with precombustion chamber, which has good performance of 21bar BMEP at engine speed 1000rpm and low $NO_X$ emission of 50ppm at 15% oxygen composition, has been developed recently. Especially, it has a good thermal efficiency of 45% and a reduction efficiency of green house gas($CO_2$) emission of 25% than a conventional diesel engine.

• International Commerce and Information Review
• /
• v.18 no.4
• /
• pp.165-193
• /
• 2016

This paper conducts a comparative analysis of the KORUS FTA and the TPP Agreement to assess the current state of affairs in international trade rules for the pharmaceutical industry. Intellectual property rights as well as public health related regulations have evolved to strengthen the position of innovator drug companies. In particular, the TPP Agreement which adopted data exclusivity for biologics for the first time, will set the standard for the future. Apart from this however, the TPP Agreement has not gone further than the KORUS FTA and in some respects, even contains greater policy flexibilities and provisions for market access than the KORUS FTA. Korea should take advantage of such differences when and if she must engage in negotiations to join the TPP Agreement or a renegotiation of the KORUS FTA.

• Journal of the Korean Society of Industry Convergence
• /
• v.25 no.4_2
• /
• pp.699-706
• /
• 2022

In this study, Directed energy deposition (DED) among additive manufacturing is applied to repair damaged spindle key parts of planner miller. The material of the spindle key is SCM415, and the P21 Powder is used. In order to find the optimal deposition conditions for DED equipment, a single-line deposition experiment is conducted to analysis five parameters. The laser power affects the width, and the height is a parameter affected by coaxial gas and powder gas. In addition, laser power, powder feed rate, coaxial gas, and powder gas are parameters that affect dilution. Otimal deposition is that 400 W of laser power, 4.0 g/min of powder feed rate, 6.5 L/min of coaxial gas, 3.0 L/min of powder gas and 4.5 L/min of shield gas. By setting the optimum conditions, a uniform deposition cross section in the form of an ellipse can be obtained. Damage recovery process of spindle key consists of 3D shape design of the base and deposition parts, deposition path creation and deposition process, and post-processing. The hardness of deposited area with P21 powder on the SCM415 spindle key is 336 HV for the surface of the deposition, 260 HV for the boundary area, and 165 HV for the base material.