• Journal of Advanced Navigation Technology
• /
• v.27 no.5
• /
• pp.546-551
• /
• 2023

In this study, a beam steering measurement system was developed to perform functions such as far-field beam steering and near-field beam focusing for TX/RX modes in the near file of the AESA radar. The beam steering measurement system consists of a spherical near-field scanner, an antenna positioner, a near-field controller, a network analyzer, a radar control system, a verification radar, a simulated radio, and an AESA radar. Using the developed system, the characteristics of TX/RX patterns before and after installation of radome to AESA radar were measured, and the beam pattern was analyzed through conversion to far field-after near-field measurement.The boresight error of the radar antenna device was measured, and it was confirmed that the main lobes were formed the same before and after the simulated radar dome was mounted.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.10
• /
• pp.45-52
• /
• 2008

We investigated the design of an RF-powered, wireless temperature sensor tag chip using $0.18-{\mu}m$ CMOS technology. The transponder generates its own power supply from small incident RF signal using Schottky diodes in voltage multiplier. Ambient temperature is measured using a new low-power temperature-to-voltage converter, and an 8-bit single-slope ADC converts the measured voltage to digital data. ASK demodulator and digital control are combined to identify unique transponder (ID) sent by base station for multi-transponder applications. The measurement of the temperature sensor tag chip showed a resolution of $0.64^{\circ}C/LSB$ in the range from $20^{\circ}C$ to $100^{\circ}C$, which is suitable for environmental temperature monitoring. The chip size is $1.1{\times}0.34mm^2$, and operates at clock frequency of 100 kHz while consuming $64{\mu}W$ power. The temperature sensor required a -11 dBm RF input power, supported a conversion rate of 12.5 k-samples/sec, and a maximum error of $0.5^{\circ}C$.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.41 no.11
• /
• pp.1619-1625
• /
• 2012

The purpose of this study is to determine long-term storage conditions for winter kimchi. Kimchi was stored in a kimchi refrigerator for 6 months with or without fermentation. Four different temperature systems used were as follows: 5 days at $10^{\circ}C$ followed by storage at $-2.5^{\circ}C$ (F1), 1 day at $15^{\circ}C$ followed by storage at $-2.5^{\circ}C$ (F2), storage at $-1^{\circ}C$ (S1), or at $-2.5^{\circ}C$ (S2). Time periods required for F1, F2, S1, or S2 kimchi to reach pH 4.4 and acidity 0.6% were 2, 8, 12, and 22 weeks, respectively. Lactobacillus spp. growth on F1 and F2 kimchi was faster and greater than that on S1 and S2 kimchi, revealing a maximum concentration of 8~9 verses 6.8 log CFU/mL, respectively. However, Leuconostoc spp. were fully grown (8~9 log CFU/mL) on all four kimchi samples regardless of temperature, even at $-2.5^{\circ}C$, although the times required to reach maximum growth were different. Growth of Lactobacillus and Leuconostoc spp. both decreased after reaching maximum levels, except for F1 kimchi. Sensory evaluation results for 3 month storage showed that F1 kimchi was the best among kimchi samples in terms of appearance, acidic taste, carbonated taste, crispiness, and moldy smell. For 6 months of storage, F1 and S1 kimchi were the most highly evaluated among the kimchi samples. Sensory evaluation result for S1 kimchi stored at $-1^{\circ}C$ was comparable to that of F1 kimchi due to fully grown Leuconostoc spp. Acidities of F1 and S1 kimchi after 6 months of storage were 0.8 and 0.7%, respectively. Taken together, fermentation of kimchi at $10^{\circ}C$ for 5 days followed by storage at $-2.5^{\circ}C$ for 6 months was optimal for high quality kimchi. Sensory properties of winter kimchi were significantly influenced by the degree of fermentation.

• KEPCO Journal on Electric Power and Energy
• /
• v.2 no.4
• /
• pp.577-582
• /
• 2016

This Study focused on the development of SMPS (Switching Mode Power Supply) to supply the constant votage and current nevertheless LED fluorescent Light generated the electric noise (with Harmonics) and Inrush current at instant time of turn-on and off. Recently, according to the Green policy in government, the LED fluorescent Lighter showed the rapidly increasing tend as indoor and outdoor Lighter. But, because of costs, LED fluorescent Light not considered and neglected the following items; power factor, efficiency, Harmonics and Inrush current. So, we are developed the SMPS about 3 key issues as follows: 1st, power factor and efficiency is 85%. 2nd, the switching noisy by harmonic is minimized. 3rd, the Inrush current at turn on and off time is reduced the minimum 0.3 A after $100{\mu}sec$ on turnon time. The proposed SMPS adjusted by LNK 409 driver (included the high frequency modulation function). Although, the developed SMPS maintained the about 85% of power factor and efficiency. but, the SMPS must be generated low heat by the variation of minute load current at switching timing. To improve the above weak point, the developed SMPS have the feedback monitoring circuit between input side and output side to maintain the power factor and efficiency. Also, we are studied the time-constant of control circuit to output the constant voltage and current nevertheless the load disturbance of LED lighting. The LED fluorescent Light of 46W is checked the above items.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.29 no.2
• /
• pp.122-129
• /
• 2009

Recently much attention has been paid to a guided wave due to its effective applicability to long range and fast inspection of structures. In guided wave based NDE, the appropriate selection of wave modes is one of important factors since the test performance is highly dependent on which mode of guided waves is employed. As far as plate-like structures are concerned, so far, SH guided wave has not been frequently applied compared to Lamb waves, which is mostly caused by the lack of proper and convenient transducers to generate and measure the SH waves. In this investigation, a new small-sized SH guided wave transducer based on magnetostriction is proposed. The present transducer was designed to be modular and be used with shear couplant to avoid the inconvenience of the existing magnetostrictive patch transducers, which comprises the ferromagnetic patch tightly bonded to a structure. The wave transduction mechanism and the detailed configuration of the present transducer are presented. Experimental verification is also conducted on test specimens and the results confirm the good performance of the present transducer module.

• Journal of Korean Ophthalmic Optics Society
• /
• v.4 no.2
• /
• pp.45-49
• /
• 1999

The second harmonic, wavelength is 397nm, of the continuous wave diode laser, whose maximum power is 35mW, was generated in $LiIO_3$ crystals in a ring enhancement cavity. 5mm- and 10mm-long crystals cut $43.21^{\circ}$ for optic axis were used in this experiment. Both surfaces of those were anti-reflection coated for 794nm. In case the crystal was inserted into the cavity, the condition of separation between two concave mirrors for the optimum mode matching was found. The conversion efficiency of second harmonic generation was increased by the resonant enhancement of pumping power in the ring enhancement cavity, and the frequency of diode laser was locked to that of the counter-propagation mode generated from the surface of crystal. When the pumping power was 28 mW, the infrared buildup factor was about 45 without the crystal, and 14 with the crystal due to the transmission loss of crystal. The maximum second harmonic powers of $1.5{\mu}W$ and $6.6{\mu}W$ were obtained, and corresponding conversion efficiencies were $(6.584{\pm}0.56){\times}10^{-3}$%, $2.6{\pm}0.21){\times}10%{-2}$% in 5mm- and 10mm-long $LiIO_3$, respectively.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1992.10a
• /
• pp.25-30
• /
• 1992

최근 전자계산기를 이용한 진동해석 방법이 눈부시게 발달하여, 일반 구조물 이나 기계 구조물 등의 동특성을 설계 단계에서 정도 높게 예측하는 것이 가능하게 되었다. 그러나 종래의 구조해석은 주어진 시스템의 동특성을 위한 것으로 얻어진 동특성으로부터 질량, 관성제원 및 스프링상수값 등의 설계상 수값을 규명하는 연구는 미미한 실정이다. 이것에 대한 해결방법으로 크게 해석적인 방법과 실험적인 방법으로의 접근이 있어 왔다. 해석적인 방법으로 유한요소해석에서 얻은 모드좌표를 물리좌표로 변환하는 방법으로 Guyan의 정축소와 같은 절점축소를 행하는 방법이 고찰되었다. 실험적인 방법으로 가 진실험에서 얻은 전달함수나 모드파라미터로부터 [M], [K] 행렬을 결정하는 연구가 있었지만 어떤것도 질량, 스프링상수 등의 설계상수를 완전히 규명하 지는 못하였다. 또한, 설계 단계에서 필요한 질량, 관성제원 또는 스프링상수 등의 최적한 값이나, 원하는 시스템특성을 얻을 수 있는 설계상수의 적정한 폭을 구하는 연구는 설계자의 경험과 반복된 시행착오에 의존하는 실정이다. 감도해석은 이러한 문제점을 개선하는 수단으로 설계변수에 대한 동특성의 변화율을 구하는 것이다. 감도해석을 수행하는 것은 어느 설계변수를 수정하 는 것이 주어진 동특성에 부합되는 지를 알려주고, 어느 것을 수정하는 것이 원하는 방향의 동특성변화에 가장 효과적인지를 알려주는 것이다. 따라서 감 도해석을 이용하여 설계의 최적화 프로그램을 만들수 있고, 이것은 설계자가 요구하는 동특성을 목적함수로 하여 주어진 구조물을 최적화하는 설계상수 값을 얻을 수 있게 한다. 본 논문에서는 강체모델의 동특성으로부터 모델의 설계 상수를 규명하고, 동특성의 개선을 위하여 설계변수의 변경량을 물리좌 표계에서 얻는것을 목적으로 한다. 강체 마운트계의 관성제원 및 마운트강성 의 규명을 위하여 임으로 주어진 설계상수를 모델데이타로 하여 관성제원과 스프링 강성을 구하였다. 관성제원의 규명은 주어진 모델의 관성값을 모르는 것으로 하여 임의의 초기 관성값으로 감도해석에 의해 주어진 계의 관성값 을 물리 좌표계에서 규명하였다. 마운트 강성의 규명도 관성제원의 규명과 같은 방법으로 임의의 강성값으로 감도해석을 하여 강성값을 규명하였다. 또 한 감도해석에 의한 동특성 변경은 특정한 고유진동 수의 변경이 필요할 때, 고유진동수의 이동을 위한 관성제원의 변경 및 마운트 강성변경값을 예측할 수 있다. 본 연구수행의 기본적인 흐름도는 Fig.1.1과 같다. 위와 같은 작업 으로 엔진 마운트와 같은 강체 모델의 시스템 규명을 행하는 경우에 유한요 소해석 및 가진 실험으로 얻은 고유진동수의 정보 또는 원하는 고유진동수 의 특성을 기본으로 실제 설계에서 사용이 가능하도록 물리 좌표계에서 관 성 제원 및 스프링상수를 구할 수 있을 것이다.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.11C
• /
• pp.1085-1097
• /
• 2009

We present a structure and design method of the D8PSK modem compatible with the VDL mode-2 standard and performance test results of the developed modem. In VDL mode-2, the raised cosine filter is used only in the transmitter and a general low pass filter is used in the receiver. Consequently, we can not achieve ISI reduction but can have better spectrum characteristics. Although there is 1~2 dB performance degradation with an un-matched filter compared to that with a matched filter, it is more important to minimize adjacent channel interference in narrow band communications. The transmit signal is generated digitally to avoid the problems(I/Q imbalance and DC offset etc.) of analog modulators. In addition the digital down converter using digital IF sampling technique is adopted for the receiver. This paper contains the overall configuration, design method and simulation results based in part on the previously proposed structures and algorithms. It is confirmed that the modem transmits and receives messages successfully at a speed of max. 870 km/h over ranges of up to 310 km through the ground and in-flight communication tests.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.10
• /
• pp.892-899
• /
• 2016

In this paper, an X-band 50 W internally matched power amplifier is designed and fabricated using an $80{\times}150{\mu}m$ GaN HEMT that is developed by the $0.25{\mu}m$ GaN HEMT process of ETRI. The optimum source and load impedances are experimentally extracted from the loadpull measurement using impedance-transform-prematching circuits, and the transistor performance is predicted. The power performance of the internally matched power amplifier, whose matching circuits are fabricated on a substrate with ${\varepsilon}_r$ of 10.2, is measured under the pulsed mode of $100{\mu}s$ pulse period and 10 % duty cycle, and the best output power of 47.46 dBm(55.5 W) and the power-added efficiency of 46.6 % are obtained at 9.2 GHz. The output power of 47~47.46 dBm(50~55.7 W) is measured in 9.0~9.5 GHz, and the power-added efficiency is measured to be greater than 43 % in 9.0~9.3 GHz and above 36 % in 9.4~9.5 GHz.

• Korean Journal of Optics and Photonics
• /
• v.33 no.4
• /
• pp.137-145
• /
• 2022

A directional coupler device, one of the fundamental components of photonic integrated circuits, distributes optical power by evanescent field coupling between two adjacent optical waveguides. In this paper, the design process for manufacturing a directional coupler device is reviewed, and the accuracy of the design results, as seen from the characteristics of the actual fabricated device, is confirmed. When designing a directional coupler device through a two-dimensional (2D) beam-propagation-method (BPM) simulation, an optical structure is converted to a two-dimensional planar structure through the effective index method. After fabricating the directional coupler device array, the characteristics are measured. To supplement the 2D-BPM results that are different from the experimental results, a 3D-BPM simulation is performed. Although 3D-BPM simulation requires more computational resources, the simulation result is closer to the experimental results. Furthermore, the waveguide core refractive index used in 3D-BPM is adjusted to produce a simulation result consistent with the experimental results. The proposed design procedure enables accurate design of directional coupler devices, predicting the experimental results based on 3D-BPM.