• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.19-19
• /
• 2011

수중방전은 다양한 라디칼을 직접 물 속에서 발생시키기 때문에 수처리 공정에 다양한 응용이 가능하다. 특히, 최근에 선박평형수 등의 살균이 국제적인 이슈가 되고 있고, 2017년까지는 모든 선박에 살균을 위한 수처리 설비가 의무화된다. 본 연구에서는 염분이 있는 수체에서의 방전공정을 연구하고 이를 수처리공정에 적용할 수 있는 방법에 대해 연구하였다. 해수의 경우 전도도가 53mS로 자유로운 전하의 이동이 가능하기 때문에 일반적인 민물방전의 전원과 전극 등으로는 방전을 할 수 없다. 이에 세라믹과 금속의 이중구조로 되어 있는 모세관전극을 개발하여 전도성이 있는 수체에서의 방전을 이루었다. 전원장치로는 60 Hz, 380 V를 1차측에 인가하여 2차측에서 약 3 kV, 10 kW의 파워가 발생하는 12위상차 교류전원장치를 개발하여 사용하였다. 모세관 내부에 전압이 인가되면 전류가 발생하여 joule heating에 의하여 모세관 내부에 기포가 형성된다. 이 때, 전류의 단락이 이루어지면서 고전압쪽에 전하가 축적되며 기포내부의 E-field가 상승한다. 이후 기포 내에서 방전이 개시되며 각종 라디칼을 생성한다. 방전에 의해 생성되는 산화제로는 오존, OH라디칼, 과산화수소 등이 있으며, 해수에서는 Cl-의 결합에 의하여 Cl2 가스가 발생한다. 약 30,000 J/L의 체적에너지에 대하여 생성되는 총염소의 농도는 2.5 mg/L이다. 수중방전의 적용대상으로 선박평형수, 멤브레인과의 결합, 용존기포부상법을 선정하여 적용가능성을 연구하였다. 먼저 선박평형수 살균처리를 위해 해수의 처리유량을 20 lpm으로 유지하고 대장균, 바실러스, 조류(테트라셀미스) 등을 투입하여 전극 12개가 삽입된 12위상차 플라즈마 반응기를 통과시켰더니, 약 30,000 J/L의 체적에너지에 대하여 1일 후의 살균력이 각각 99.99, 99.99, 99.9%의 살균력을 나타내었다. 이는 국제해사기구에서 권장하는 살균수준인 99.9%를 초과하는 수치이다. 플라즈마를 이용한 해수살균공정의 안정적 운전을 위해 후단에 UF멤브레인을 추가하여 잔류생존 미생물을 제거할 수 있다. 이를 위해 플라즈마가 후단의 멤브레인 운전에 미치는 영향을 평가하였다. 카올린과 탄산칼슘을 오염원으로 각각 투입하여 멤브레인으로 처리를 하였을 때, 방전 직후 멤브레인에 걸리는 막간압력차가 약 30% 감소하였는데, 이는 막에 형성된 파울링이 방전에 의해 제거된 것으로 평가할 수 있다. 수중방전은 다양한 산화제를 생성함과 동시에 미세기포를 발생시키는데 이는 수중유기물의 부상분리에 적용될 수 있다. 방전모세관전극의 내부직경을 1 mm로 유지하고, 60 Hz, 교류전원으로 방전한 결과 평균입경 44 um의 기포를 발생시켰고, 이는 일반적으로 용존공기부상법에 사용되는 기포의 크기와 일치한다.

• Applied Microscopy
• /
• v.38 no.4
• /
• pp.339-345
• /
• 2008

In this study, we compared the stress and tensile strength of the hair treated with oxidative permanent dye with those of virgin hair. We investigated the fine structure of the hair section after the tensile test using scanning electron microscopy. The tensile strength of the virgin hair was measured as $14.66\;g/cm^2$, tensile energy was $108\;erg/cm^2$, and the maximum stress was 146.64g. Those of the dyed hair were $13.69\;g/cm^2$, $89.62\;erg/cm^2$ and 136.90 g, respectively. The differences in the tensile strength, the tensile energy and the maximum stress were $-0.97\;g/cm^2$, $-18.38\;erg/cm^2$, -9.74 g, respectively, which showed that the dyed hair had less elasticity and strength than the virgin hair. In the scanning electron microscopy investigation of the damaged hair after the tensile test, lift-off of the cuticle outer layer were shown in both virgin hair and dyed hair, which was more severe in the dyed hair than the virgin hair. Adjacent cuticular cells of the cuticle layer were separated by the destruction of intercellular membrane complex. The macrofibrils were exposed and separated from the cortex torn by tensile strength.

• Transactions of the Korean hydrogen and new energy society
• /
• v.22 no.1
• /
• pp.1-12
• /
• 2011

To improve the mechanical properties, such as durabilities and antioxidative characteristics, the covalently cross-linked (CL-) SPEEK (sulfonated polyether ether ketone)/Cs-substituted HPA (heteropoly acid) organic-inorganic composite membranes (CL-SPEEK/Cs-HPAs), have been intensively investigated. The composite membrane were prepared by blending cesium-substituted HPAs (Cs-HPAs), including tungstophosphoric acid (TPA), molybdophosphoric acid (MoPA), and tungstosilicic acid (TSiA) with cross-linking agent content of 0.01 mL. And composite electrolytes composed of Cs-HPAs, prepared by immersion (imm.) and titration (titr.) methods to increase the stability of HPAs in water, were applied to polymer electrolyte membrane electrolysis (PEME). As a result, the proton conductivity of Cs-substituted composite membranes increased rapidly over $60^{\circ}C$ but mechanical properties, such as tensile strength, decreased in accordance with added Cs content. The bleeding-out of Cs-TPA membranes by titration method (50 vol.% Cs) decreased steadily to 2.15%. In the oxidative stability test by Fenton solution, the durability of membranes with Cs-HPA significantly increased. In case of CL-SPEEK/ Cs-TPA membrane, duration time increased more than 1200 hours. It is expected that even though CL-SPEEK/Cs-MoPA membrane shows the high proton conductivity, electrocatalytic activity and cell voltage of 1.80 V for water electrolysis, the CL-SPEEK/Cs-TPA (imm.) is more suitable as an alternative membrane in real system with the satisfactory proton conductivity, mechanical properties, anti-oxidative stability and cell voltage of 1.89 V.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.45 no.1
• /
• pp.82-89
• /
• 2018

In a photodynamic therapy, the difference of antibacterial capacity was compared according to the type of source of light when the same quantity of energy is irradiated. After S. mutans is formed in planktonic state and biofilm state, erythrosine diluted to $40{\mu}M$ was treated for 3 minutes, and as the type of light source, Halogen, LED, and Plasma arc were used, which were irradiated for 30 seconds, 15 seconds and 9.5 seconds, respectively. After the completion of the experiment, CFU of each experiment arm was measured to compare the photodynamic therapeutic effects according to each condition. The CFU of each experiment arm had no statistically significant difference. Under the same quantity of energy, the photodynamic therapeutic effect can be said to be the same regardless of types of light source, which is a useful result in the clinical field with various light irradiators.

• Journal of the Microelectronics and Packaging Society
• /
• v.14 no.1
• /
• pp.49-53
• /
• 2007

The direct methanol fuel cell (DMFC) is a promising power source for portable applications due to many advantages such as simple construction, compact design, high energy density, and relatively high energy-conversion efficiency. In this work, an electrochemical methanol sensor for monitoring the methanol concentration in direct methanol fuel cells was fabricated using a thin composite nafion membrane as the electrolyte. We have analyzed the I-V characteristic of the fabricated methanol sensor as a function of methanol concentration, catalyst electrode and platinum(Pt) thickness. The fabricated sensor was analyzed by I-V measurement with various methanol concentration. When we measured the sensor characteristics with 10nm Pt and at 1V, the current value was $1.30{\times}10^{-6}A,\;1.96{\times}10^{-6}A\;and\;2.80{\times}10^{-6} A$ for three methanol concentration of 1M, 2M and 3M, respectively. When the methanol concentration was fixed at 2M, the current value of the fabricated device with Pt layers of 5, 10 and 15 nm thickness was $3.06{\times}10^{-6}A,\;1.96{\times}10^{-6}A\;and\;1.00{\times}10^{-6}A$, respectively. These results lead us to the conclusion that when the methanol concentration increases, the output current increases and when the catalyst electrode become thinner, the current increase more. It showed that, the thinner the catalyst electrode, the more electrochemistry become activation.

• Journal of the Korean Chemical Society
• /
• v.50 no.1
• /
• pp.32-36
• /
• 2006

films of gold nanoparticles were formed on indium tin oxide (ITO) by an electrodeposition method from an aminosilicate stabilized gold colloid solution. The thin films were examined by cyclic voltammetry (CV), scanning electron microscopy (SEM), UV-visible, and energy dispersive X-ray spectroscopy (EDXS). The surface coverage of gold nanoparticles on the thin film was estimated to 1.2 nanomole/cm2. An anthraquinone-2, 6-disulfonic acid, disodium salt (AQDS) self-assembled layer was generated by immersing gold thin film into 1mM of AQDS in 0.1M HClO4 solution for over 20 hours. As a result, a new absorbance peak from the multi-layers (AQDS/thin film of gold /ITO) was obtained about at 690 nm. Also, the surface plasmon absorption of multi-layers was measured by UV-Visible spectrometer along with chronoamperometry by applying the various potentials from +0.5V to -0.5V. The maximum surface plasmon absorption band at 550 nm was decreased by applying negative potentials. The change of absorbance was correlated with the surface coverage of the AQDS indicating the pseudo-capacity surface state of the AQDS layer was coupled to the energy level of the plasmonband by applied negative potentials.

• Solar Energy
• /
• v.17 no.4
• /
• pp.3-11
• /
• 1997

Because grain boundaries in polycrystalline silicon act as potential barriers and recombination centers for the photo-generated charge carriers, these defects degrade conversion effiency of solar cell. To reduce these effects of grain boundaries, we investigated various influencing factors such as thermal treatment, various grid pattern, selective wet etching for grain boundaries, buried contact metallization along grain boundaries, grid on metallic thin film. Pretreatment above $900^{\circ}C$ in $N_2$ atmosphere, gettering by $POCl_3$ and Al treatment for back surface field contributed to obtain a high quality poly-Si. To prevent carrier losses at the grain boundaries, we carried out surface treatment using Schimmel etchant. This etchant delineated grain boundaries of $10{\mu}m$ depth as well as surface texturing effect. A metal AI diffusion into grain boundaries on rear side reduced back surface recombination effects at grain boundaries. A combination of fine grid with finger spacing of 0.4mm and buried electrode along grain boundaries improved short circuit current density of solar cell. A ultra-thin Chromium layer of 20nm with transmittance of 80% reduced series resistance. This paper focused on the grain boundary effect for terrestrial applications of solar cells with low cost, large area, and high efficiency.

• Food Science and Preservation
• /
• v.13 no.5
• /
• pp.555-562
• /
• 2006

This study was conducted to investigate the rheological properties of protein-bound polysaccharide powders (SD-1, 2, 3) using ultrafiltration (UF) and spray drying (SD) process from Agaricus blazei Murill. The calculated weight-average molar mass (Mw) in the positions at 29.7 mL (for SD-1), and at 27.8 mL (for SD-2), and at 18.7 mL (for SD-3) was $8.2{\times}10^3,\;9.6{\times}10^4$, and $5.9{\times}10^6g/mol$, respectively. As concentration increased the solution showed higher pseudoplasticity where the pseudoplasticity decreased as temperature increased. The flow behaviors of spray dried powder solutions were more fitted to Herschel-Bulkley equation than Power law equation. Apparent viscosity of SD-2 was more temperature-dependent than that of SD-1 and 3. However, the SD-3 tended to be more concentration-dependent than SD-1 and 2 as temperature increasing.

• Transactions of the Korean hydrogen and new energy society
• /
• v.30 no.6
• /
• pp.523-530
• /
• 2019

For the low-Pt electrodes for polymer electrolyte fuel cells (PEMFCs), the optimization of ionomer content for anode catalyst layers was carried out. A commercial catalyst of 20 wt.% Pt/C was used instead of 50 wt.% Pt/C which is commonly used for PEMFCs. The ionomer content varies from 0.6 to 1.2 based on ionomer to carbon ratio (I/C) and the catalyst layer is formed over the electrolyte by the ultrasonic spray process. Evaluation of the prepared MEA in the unit cell showed that the optimal ionomer content of the air electrode was 0.8 on the I/C basis, while the hydrogen electrode was optimal at the relatively high ionomer content of 1.0. In addition, a large difference in cell performance was observed when the ionomer content of the hydrogen electrode was changed. Increasing the ionomer content from 0.6 to 1.0 by I/C in a hydrogen electrode with 0.05 mg/㎠ platinum loading resulted in more than double cell performance improvements on a 0.6 V. Through the analysis of various electrochemical properties in the single cell, it was assumed that the change in ionomer content of the hydrogen electrode affects the water flow between the hydrogen and air electrodes bounded by the membrane in the cell, which affects the overall performance of the cell. A more specific study will be carried out to understand the water flow mechanism in the future, and this study will show that the optimization process of hydrogen electrode can also be a very important cell design variable for the low-Pt and high-performance MEA.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.76-76
• /
• 2000

최근 비정질 SiC 박막은 열과 광안정도면에서 비정질 Si 박막에 비해 우수하며 공정변수들을조절함으로써 비교적 쉽고 다양하게 광학적.전기적 특성을 얻을 수 있고, 낮은 광흡수계수 및 105($\Omega$cm)1 이상의 높은 전도도를 가지고 있어 Plasma Enhanced Chemical Vapor Deposition(PECVD)을 통해 가전자제어 (Valency electron control)가 가능한 비정질 SiC 박막이 제작된 이래 대한 많은 연구가 진행되고 있다. 결정성이 없는 비정질 물질은 상대적으로 낮은 온도에서 성장이 가능하며, 특히 glow-sidcharge 방식으로 저온에서 성장시킬 수 있음에 따라 유리등과 같은 다른 저렴한 물질을 기판으로 이용, 넓은 면적의 비정질 SiC 박막을 성장시켜 여러 분야의 소자에 응용되고 있다. 비정질 SiC 박막이 넓은 에너지띠 간격을 갖는 물질이라는 점과 화학적 안정성 및 높은 경도, 비정질성에 기인한 대면적 성장의 용이성 등의 장점이외에, 원자의 성분비 변화에 의해 에너지띠 간격(1.7~3.1eV)을 조절할 수 있다는 점은 광전소자의 응용에 큰 잠재성이 있음을 나타낸다. PECVD 방식으로 성장된 비정질 SiC 박막은 태양전지의 Window층이나 발광다이오드, 광센서, 광트랜지스터 등에 응용되어 오고 있다. 본 연구에서는, RF-PECVD(ULVAC CPD-6018) 방법에 의하여 비정질 Si1-xCx 박막을 2.73Torr의 고정된 압력에서 RF 전력(50~300W), 증착온도(150~30$0^{\circ}C$), 주입 가스량 (SiH4:CH4)등의 조건을 다양하게 변화시켜가며 증착된 막의 특성을 평가하였다. 성장된 박막을 X-ray Photoelectron Spectroscopy(XPS), UV-VIS spectrophotometer, Ellipsometry, Atomic Force Microscopy(AFM)등을 이용하여 광학적 밴드갭, 광흡수 계수, Tauc Plot, 그리고 파장대별 빛의 투과도의 변화를 분석하였으며 각 변수가 변화함에 따라 광학적 밴드갭의 변화를 정량적으로 조사함으로써 분자결합상태와 밴드갭과 광 흡수 계수간의상관관계를 규명하였고, 각 변수에 따른 표면의 조도를 확인하였다. 비정질 Si1-xCx 박막을 증착하여 특성을 분석한 결과 성장된 박막의 성장률은 Carbonfid의 증가에 따라 다른 성장특성을 보였고, Silcne(SiH4) 가스량의 감소와 함께 박막의 성장률이 둔화됨을 볼 수 있다. 또한 Silane 가스량이 적어지는 영역에서는 가스량의 감소에 의해 성장속도가 둔화됨을 볼 수 있다. 또한 Silane 가스량이 적어지는 영역에서는 가스량의 감소에 의해 성장속도가 줄어들어 성장률이 Silane가스량에 의해 지배됨을 볼 수 있다. UV-VIS spectrophotometer에 의한 비정질 SiC 박막의 투과도와 파장과의 관계에 있어 유리를 기판으로 사용했으므로 유리의투과도를 감안했으며, 유리에 대한 상대적인 비율 관계로 투과도를 나타냈었다. 또한 비저질 SiC 박막의 흡수계수는 Ellipsometry에 의해 측정된 Δ과 Ψ값을 이용하여 시뮬레이션한 결과로 비정질 SiC 박막의 두께를 이용하여 구하였다. 또한 Tauc Plot을 통해 박막의 optical band gap을 2.6~3.7eV로 조절할 수 있었다.