• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.1063-1066
• /
• 1995

This paper presents a precition control of an electrostatic microactuator. For the generation of sufficient electrostatic force, a donse comb-type electrostatic microactuator is designed and manufactureed via MEMS (micro-electro-mechanical systems) process. The nonlinear plant and the linear plant of the microactuator are established through the comparison of experimental results and simulation results. A feedforward controller is designed via MATLAB simulation using the inverse function of the nonlinear plant. the experiment for the precise position tracking control is undertaken to show the control efficiency of the proposed controller.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2002.11a
• /
• pp.285-289
• /
• 2002

In this paper, microstrip line-probe feeding patch array antenna with center frequency 5.8㎓ is designed and manufactured. The microstrip line - probe feeding structure has broadband characteristic and be able to modify the array structure for improving antenna gain. In this result, microstrip line-probe feeding patch array antenna has 17.6% bandwidth and 8㏈i antenna gain, respectively.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.717-722
• /
• 2003

To improve the shock resistance of the microdrive under non-operating conditions, an isolator was attached to the contacting part of the microdrive. Through FE analysis, design parameters for satisfying the allowable acceleration level of the spindle motor bearing part were presented, which is a most possible critical part of the microdrive.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.115-118
• /
• 2002

The purpose of this paper is to design a pick-up for the small form factor optical disk drive and to fabricate a micro-compensatory lens for the pick-up using the micro-compression molding process. At design stage, the optical elements including the objective lens and the compensatory lens are miniaturized. The height of pick-up and free working distance are designed as 2mm and 0.2% respectively. To analyze the fabricated micro-compensatory lens, the system was analyzed using the surface profile of the fabricated micro-compensatory lens and CODE V which is commercial software. The RMS wave front aberration of the system using fabricated micro-compensatory lens is 0.01677λ which is lower than Marechal's criterion, 0.07λ.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.7
• /
• pp.687-692
• /
• 2002

The design of broadband patch antenna with the new feeder structure is proposed in this paper. The antenna operates in the center frequency 5.8 GHz. Proposed the new feeder structure has also broadband characteristic and reduced antenna size. To confirm broadband characteristic, compared with probe feeder antenna. After designing and manufacturing, the antenna bandwidth enhanced by 34.5 % and the patch size reduced by 45 %.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.05a
• /
• pp.40.2-40.2
• /
• 2009

일반적으로, 극미세 공정조직은 높은 강도를 나타내지만 낮은 연성을 가지는 단점을 보이고 있다. 극미세 공정합금의 연성을 증대시키고자, 상대적으로 연한 고용체 또는 경한 금속간 화합물을 마이크로 크기의 초정상으로 형성시키는 연구가 활발히 진행 되어지고 있다. 이러한 마이크로 크기의 초정상은 극미세 공정합금의 연성을 증가시키기에는 효과적이지만, 강도가 큰 폭으로 낮아지는 손실을 나타내고 있다. 최근, 공정조직 만으로 이루어진 극미세 공정합금의 연성을 증대시키고자, 공정조직의 형상 및 구성상을 조절하는 등의 연구가 발표되어지고 있다. 본, 연구에서는 Ti-, Mg-계 합금에 양극화 공정조직을 유도하여 극미세 공정조직 양극화 Ti-, Mg-합금을 개발, 이러한 불균일성을 내포한 양극화 공정조직이 극미세 공정조직 양극화 Ti-, Mg-합금의 기계적 성질에 미치는 영향을 체계적으로 연구하였다.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.9
• /
• pp.605-610
• /
• 2001

Electrostatic comb-drive microactuators with sub-micron gap were fabricated and tested. We designed and fabricated two type of electrodes which are rectangular and triangular tip. The fabricated microactuators with triangular tip resulted in the electrode gaps in the range of 0.55 ${\mu}{\textrm}{m}$~1.35 ${\mu}{\textrm}{m}$ Displacement of 1 ${\mu}{\textrm}{m}$ and electrostatic force of 2.3 $\mu$N were observed in a triangular-tip microactuator with 0.55 ${\mu}{\textrm}{m}$ gap when a DC drive voltage of 13 volts was applied. Measured 1st resonance frequency of microactuators was about 23 kHz.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.12
• /
• pp.29-36
• /
• 2004

In this paper, a new replication technique for a real 3D microstructure was introduced, in which a master Pattern WES made of photo-curable epoxy using a microstereolithography technology, and then it was transferred onto an epoxy-copper particle composite. A helical gear was selected as one of the real 3D microstructure for this study, and it was replicated from a pure epoxy to an epoxy composite. In addition, the transferability of the microreplication process was evaluated, and the properties of :he epoxy composite were compared to that of the pure epoxy, including hardness, wear-resistance and thermal conductivity.

• Proceedings of the Korean Information Science Society Conference
• /
• 2001.10c
• /
• pp.148-150
• /
• 2001

Mobile IP(MIP)[1] Working Group에서 제안하고 있는 멀티캐스트 적용 방안에는 크게 HA기반 라우팅과 FA기반 라우팅으로 구분된다. HA기반 라우팅 방법은 멀티캐스트 패킷을 HA에서 터널링하는 방법을 사용하므로 경로의 최적화가 이루어지지 않게 되며 터널 집중화 현상이 발생하게 된다. FA기반 라우팅 방법은 이동 호스트의 핸드오프가 일어날 때마다 멀티캐스트 트리의 재구성이 필요하므로 많은 오버헤드가 발생하지만 경로 최적화는 얻을 수 있다. 본 논문은 HA기반 라우팅과 FA기반 라우팅 방안을 절충한 새로운 멀티캐스트 제공 방안을 제안한다. MH의 이동이 빈번한 마이크로 레벨에서는 HA기반 라우팅을 이용하고, MH의 이동 거리가 큰 매크로 레벨에서는 경로 최적화를 위하여 새로운 멀티캐스트 트리를 재구성함으로써 보다 효율적 멀티캐스트 서비스가 가능한 메커니즘의 프로토타입을 제안한다.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.3 no.1
• /
• pp.45-51
• /
• 2004

In this paper, the relationship between the mechanical properties of alumina abrasives and grinding performance was investigated. Micro vickers hardness and fracture strength of all abrasives used in this study were measured. The grinding experiments were earned out with alumina grinding wheels made by various kinds of alumina abrasives including 32A, WA, ART, ALOMAX, and RA. The performance of such grinding wheel for grinding SKD11 was evaluated by specific grinding energy, grinding-ratio, and surface roughness. The grinding wheels composed by the harder abrasives and the lower fracture strength abrasives showed better grinding performance.