• Tribology and Lubricants
• /
• 제36권4호
• /
• pp.207-214
• /
• 2020

In this study, we investigated the effects of copper and copper-alloy on the frictional and wear properties of low-steel friction material. The proportions of copper and copper-alloy in the brake friction materials used in passenger cars are very high (approximately 5-20% weight), and these materials have significant effects on friction and wear characteristics. In this study, the effects of cupric ingredients, such as the copper fiber and brass fiber, are investigated using the friction materials based on commercial formulations. After the copper and brass fibers from the same formulation were removed, the frictional and wear characteristics were evaluated to determine the influence of the copper and copper-alloy. We evaluated the frictional and wear characteristics by simulating various braking conditions using a 1/5 scale dynamometer. The results show that the friction material containing copper and brass fibers have excellent frictional stability and a low wear rate compared to the friction material that does not contain copper and brass fibers. These results are attributed to the excellent ductility, moderate melting point, high strength, and excellent thermal conductivity of copper and copper-alloy. We analyzed the surfaces of the friction materials before and after the performing the friction tests using a scanning electron microscope-energy dispersive X-ray spectroscope, confocal microscope, and roughness tester to verify the frictional behavior of copper and copper-alloy. In future studies, it will be applied to the development of copper-free friction materials based on the results of this study.

• Tribology and Lubricants
• /
• 제22권4호
• /
• pp.211-217
• /
• 2006

Ring and groove wear may not be a problem in most current automotive engines. However, a small change in ring face and groove geometry can significantly affect the lubrication characteristics and ring axial motion. This in turn can cause to change inter-ring pressure, blow-by and oil consumption in an engine. Therefore, by predicting the wear of piston ring face, ring groove and cylinder bore altogether, the changed ring end gap and the changed volume of gas reservoir can be calculated. Then the excessive oil consumption can be predicted. Being based on the calculation of gas flow amount by the theory of piston ring dynamics and gas flow, and the calculation of oil film thickness and friction force by the analysis of piston ring lubrication, the calculation theory of oil amount through top ring gap into combustion chamber will be set. This is estimated as engine oil consumption. Furthermore, the wear theories of ring, groove and cylinder bore are included. Then the each amount of wear is to be obtained. The changed oil consumption caused by the new end gap and the new volume of oil reservoir around second land, can be calculated at some engine running interval. Meanwhile, the wear amount and oil consumption occurred during engine durability cycle are compared with the calculated values. Next, the calculated amount of oil consumption and wear are compared with the guideline of each part's wear and oil consumption. So, the timing of part repair and engine life cycle can be predicted in advance without performing engine durability test. The wear data of rings and grooves are obtained from three engines before and after engine durability test. The calculated wear data of each part are turn out to be at the lower bound of aver-aged test values or a little below.

• Tribology and Lubricants
• /
• 제36권2호
• /
• pp.75-81
• /
• 2020

In this paper, we present an experimental investigation of the leakage and endurance performances of mechanical face seals in a 75-tonf turbopump for the Korea Space Launch Vehicle II first-stage engine. A mechanical face seal is used between the fuel pump and turbine to prevent mixing of the fuel and turbine gas. However, excessive leakage occurs through the carbon attached to the mechanical face seal bellows. To reduce this leakage, we redesign the mechanical face seal such that the contact area between the fuel and carbon is reduced, height of the carbon nose is reduced, and stiffness of the bellows is increased. Then, we conduct static and dynamic leakage tests and endurance tests to compare the performances of the original and modified mechanical face seals. The investigation of the leakage of the old and new mechanical face seals confirms that the leakage performance is significantly improved, by 80%, in the new design in comparison with the old design. The endurance tests demonstrate that the average wear rate of carbon in the new mechanical face seal is 0.1094 ㎛/s. The service lifetime is predicted to be 4,200 s, which is 28 times greater than the requirement. Finally, we present a new mechanical face seal in a 75-tonf turbopump, and perform a validation test in the real-propellant test facility at the NARO Space Center. Based on the test results, we can confirm that the modified mechanical face seal works well under real operating conditions.

• 한국산학기술학회논문지
• /
• 제15권3호
• /
• pp.1253-1258
• /
• 2014

CA 이온도금기술에 의한 TiC와 TiN 그리고 TiC/TiN 코팅재를 비교하기 위하여 트라이볼로지 물성을 연구하였다. 실험은 Falex journal V block 시스템을 이용한 터보시험기에서 수행하였다. 코팅재의 마찰과 마모특성은 작용된 하중과 미끄럼 속도에 의하여 다양하게 결정되었다. TiC와 TiN 그리고 TiC/TiN 코팅재는 표면에서 트라이볼로지 특성이 현저하게 증가하였다. 단층코팅에서는 TiC보다 TiN이 좋은 결과를 얻었다. 그러나, TiC/TiN의 다층코팅은 다른 어떤 단층코팅보다 좋은 성능을 보였다. 다층코팅의 성능이 향상된 핵심요소는 TiN층 외부와 강 사이에서 부착이 증가하게된 TiC의 역할 때문이다.

• 한국자동차공학회논문집
• /
• 제22권3호
• /
• pp.33-41
• /
• 2014

Fretting is a kind of surface degradation mechanism observed in mechanical components and structures. When two pieces of materials, pressed together by an external static load, are subjected to a transverse cyclic loading or various vibrations, so that one contacting face is relatively displaced cyclically parallel to the other face, wear of the mating surfaces occurs. These fretting damages may be observed in electrical connectors for automotive components, where there are special environments and various vibration conditions. This study aims to evaluate the usefulness of fretting test equipment that was developed for reliability test of electrical connector. Fretting tests were carried out using tin coated connectors and friction force, contact resistance, contact area and roughness of contact region were investigated. The following results that will be helpful to understand the fretting wear mechanism, increase process the contact resistance and contact area were obtained. (1) In the same frequency and slip amplitude, the friction force, roughness and contact area increased rapidly until about $10^3$ cycles, after which it was slightly changed. (2) In the various frequency and slip amplitude, the contact area increased with slip amplitude and cyclic numbers, but it did not depend on cyclic frequency. (3) The surface roughness of contact region did not depend on the cyclic frequency. From these results, the applicability of the fretting wear test equipment and reliability of connector were discussed.

• 지질공학
• /
• 제8권3호
• /
• pp.235-245
• /
• 1998

도로에서의 미끄러짐을 방지하고 차량이 적당한 거리에서 정지할 수 있기 위해서는 적절한 마찰저항이 필요하다. 골재의 마찰저항력은 차량소통의 결과로 시간경과에 따라 마모 및 연마되어 감소하게 된다. 이 연구목적은 현장마찰 저항력을 예측하고 자갈골재간의 마찰저항치의 변화를 야기하는 원인을 규명하기 위해서 인디아나 자갈골재 실내시험방법을 개발하는 것이다. 자갈골재 연구에 대한 접근방법은 첫 번째로 각 각의 구성 암석형태 및 구성비율을 분석하는 것이다. 본 연구에 사용된 자갈들은 주로 탄산염암 골재로 구성되어 있으며 연마에 의한 저항치의 변화가 심하였다. 자갈을 구성하는 화성암 및 변성암은 이에 비해 연마에 의한 저항치의 변화가 적었으며 전체 골재의 마찰저항력을 증진시키는 것으로 사료된다. 파쇄자갈시료의 초기마찰 저항치 (IEV)와 연마 후 수치 (PV)의 평가는 시료 내 암종의 백분율에 따라 실행되었으며 가중평균이 적용되었다.

• 열처리공학회지
• /
• 제24권3호
• /
• pp.127-132
• /
• 2011

The silicon-containing Diamond-like Carbon (Si-DLC) film as an low friction coefficient coating has especially treated a different silicon content by plasma-enhanced chemical vapor deposition (PECVD) process at $500^{\circ}C$ on nitrided-STD 11 mold steel with (TMS) gas flow rate. The effects of variable silicon content on the Si-DLC films were tested with relative humidity of 5, 30 and 85% using a ball-on-disk tribometer. The wear-tested and original surface of Si-DLC films were analysed for an understanding of physical and chemical characterization, including a changing structure, via Raman spectra and nano hardness test. The results of Raman spectra have inferred a changing intra-structure from dangling bonds. And high silicon containing DLC films have shown increasing carbon peak ratio ($I_D/I_G$) values and G-peak values. In particular, the tribological tested surface of Si-DLC was shown the increasing hardness value in proportional to TMS gas flow rate. Therefore, at same time, the structure of the Si-DLC film was changed to a different intra-structure and increased hardness film with mechanical shear force and chemical reaction.

• 한국지반신소재학회논문집
• /
• 제5권4호
• /
• pp.27-33
• /
• 2006

흙 입자의 크기를 고려한 5종류의 샌드페이퍼를 사용하여 지오스트립/샌드페이퍼 계면에서의 마찰특성을 평가하였으며, 전단력에 의한 마찰계수와 마찰각 등을 구하였다. 설계강도가 각각 50, 70, 100KN/m인 3종류의 지오스트립이 사용되었으며, 입자 크기가 각각 P100, 220, 320, 400, 600인 5종류의 샌드페이퍼가 사용되었다. 지오스트립의 설계강도에 따라 전단강도는 큰 차이를 나타내지 않았으며, 이는 전단 시 접촉되는 지오스트립 표면이 강도에 따라 차이가 나지 않고 비슷하기 때문이다. 샌드페이퍼의 입자의 크기가 클수록 더 큰 전단강도 값을 나타내었으며, 지오스트립/P100 계면에서 가장 큰 값을 나타내었다. 끝으로 모든 시료의 경우 post-peak 강도 감소 현상이 나타났으며, 이는 전단 시험에 의한 지오스트립 표면 의 마모에 기인한다.

• 센서학회지
• /
• 제10권1호
• /
• pp.33-41
• /
• 2001

와이어 로프는 무거운 중량을 안전하게 운반하거나 기계적인 에너지를 빠르게 전송하는 곳과 같은 산업응용 분야에 광범위하게 사용되어 왔다. 특히, 운전 중 엘리베이터의 와이어 로프가 파손되면 큰 재산 상 손실과 주변 인명의 심각한 상해를 초래할 수 있다. 따라서, 와이어 로프의 정기적인 검사는 매우 중요하다. 와이어 로프의 고장 검출은 로프의 구조, 특성, 결함 특성, 검출방법과 신호처리 방법에 대한 기본적인 이해가 요구된다. 이 연구에서는 엘리베이터에 노화된 와이어 로프에 대한 마모, 단선, 부식과 형붕괴와 같은 결함을 검출하기 위하여, Hall 센서를 결합한 새로운 결함 검출시스템의 개발에 대하여 다룬다. 휴대용 계측기로서 검출기를 사용하기 위하여, Hall 센서를 가진 센싱 부분과 아날로그 신호처리 및 프로그램의 제작에 대한 몇 가지 특성들이 서술되었다. 제작된 검출시스템에 대한 실험과 실장시험 결과 역시 제시되었다. 그 결과, 검출시스템은 사용 중인 노화된 와이어 로프의 결함을 검출하는데 양호한 효율성을 갖는다는 것을 확인하였다.

• 한국표면공학회지
• /
• 제47권5호
• /
• pp.263-268
• /
• 2014

Nanocrystalline diamond(NCD) coated SiC balls were applied in a ball-on-disk tribometer. After seeding in an ultrasonic bath containing nanometer diamond powders, $2.2{\mu}m$ thick NCD films were deposited on sintered 3 mm diameter SiC balls at $600^{\circ}C$ in a 2.45 GHz microwave plasma CVD system. Bare $ZrO_2$ and SiC balls were prepared for comparison as test balls. Tribology tests were performed in air with pairs of three different balls and mirror polished steel(SKH51) disk. The wear tracks on balls and disks were examined by optical microscope and alpha step profiler. Under the load of 3 N, the friction coefficients of steel against $ZrO_2$, SiC and NCD-coated balls were between 0.4 and 0.8. After a few thousands sliding laps, the friction coefficient of NCD-coated balls dropped from 0.45 to below 0.1 and maintained thereafter. Under a higher load of 10 N or 20 N with a long sliding distance of 2 km, $ZrO_2$ and SiC balls exhibited the similar friction coefficients as above. The friction coefficient of NCD-coated balls was less than 0.1 from the beginning and increased to above 0.1 steadily or with some fluctuations as sliding distance increased. NCD coating layers were found worn out after long duration and/or high load sliding test, which resulted in the friction coefficient higher than 0.1.