• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.20-20
• /
• 2009

치아의 치석제거 및 치골절삭에 사용되는 초음파 스케일러는 일반적으로 마그넷형과 압전형으로 구분할 수 있으며, 최근에 들어 소형화, 저전력, 정밀성, 저비용 등의 장점으로 인해 압전형이 주로 사용되고 있다. 국내의 대부분의 치과에서 한 대 이상 운용되는 초음파 스케일러는 대부분 유럽 제품으로며, 국내에서는 이를 대체하기 위한 제품이 출시되고 있으나 아직까지 유럽 제품에 비해 출력강도, 정밀도 등에서 성능이 모자란 현실로 시장에서 외면 받고 있다. 본 연구에서는 앞서 언급한 압전 초음파 스케일러에 대한 체계적인 연구를 진행하여 외국에 비해 상대적으로 성능이 떨어지는 초음파 스케일러의 성능을 개선하고자 하였다. 이를 위하여 스케일러의 진동 발생부, 즉 압전 세라믹과 SUS 재질의 head, tail 부로 구성된 진동발생부의 최적구조톨 도출하기 위하여 유한요소 해석을 실시하였으며, 스케일러의 중심주파수 28kHz에서 최대 출력이 발생할 수 있는 구조를 도출하였다. 스케일러의 Head 와 Tail 부문의 두께와 직경, 길이 변화에 따른 중심주파수 및 출력 변위의 경향분석을 실시하였으며, 이상의 결과를 바탕으로 실제 스케일러를 제작하여 시뮬레이션의 유효성을 검증하였다. 이상의 과정으로 거쳐 개발된 압전 초음파 스케일러는 다양한 Tip 종류의 영향을 최소화할 수 있으며, 중심주파수는 28~30kHz 에서 뛰어난 성능을 나타내어 기종 유럽제품의 성능을 앞지르는 특성을 확보할 수 있었다.

• Progress in Superconductivity
• /
• v.8 no.1
• /
• pp.113-118
• /
• 2006

The design of superconducting magnets for a 600 kJ SEMS was discussed. The basic constraint conditions in the design of a 600 kJ SMES magnet were V-I loss(<1 W), inductance of magnet(<24 H), the number of Double Pancake Coils(DPC about 10), the number of turns of DPC(<300), outer diameter of DPC(close to 800 mm) and total length of HTS wire in a DPC(<500 m). As a result of optimum design, we obtained design parameters of the 600 kJ SMES magnet with two operating currents, 360 A and 370 A, which are in the limited conditions without V-I loss. V-I loss of each operating current was calculated with design parameters and V-I characteristic of the HTS wire. As a result of calculations, V-I losses with operating currents of 360 A and 370 A were 0.6 W and 1.86 W, respectively. Even though all design parameters of the SMES magnet in case of operating current of 360 A were in the restricted conditions, V-I loss of SMES magnet showed a tendency to generate at local DPCs, which are located on the top and the bottom of the SMES magnet more than that of the other DPCs.

• Journal of Sensor Science and Technology
• /
• v.6 no.6
• /
• pp.466-475
• /
• 1997

In this paper, an implantable middle ear hearing aids using an electromagnetic transducer which consists of a tiny coil and a magnet is designed, and objective design method to implement a vibrator of the electromagnetic type transducer is proposed. Sound characteristic of the electromagnetic type vibrator is excellent but power transfer rate is lower than that of a ceramic type. To improve power transfer efficiency of system, external and inner part of a middle ear system is designed using FM transmission method. We implemented an experimental set of the designed transducer, inner part, and outer part. Then, we measured vibration characteristics of a metal strip and a temporal bone of a dead body. As the results, we confirmed the advantage of FM method and showed that designed transducer could effectively transmit vibration of amplified input sound pressure to ossicle.

• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.1315-1317
• /
• 2005

Generally, the high Tc superconductor(HTS) doesn't generate any loss in DC condition, but generate considerable loss in AC condition. Until now AC loss in superconductor has been researched on measuring method of short sample by using electrical method and magnetization method. But it is not easy to estimate AC loss in high class magnet system with results of measuring AC Joss in short sample. In this paper, we carry out research on measuring method by using calorimetric method used in measuring AC loss in high class magnet system. We make the inductive and non-inductive superconducting magnet and measure the generated AC loss, then we compare the measured results with the calculated results using Norris equation. This measuring method of AC loss using calorimetric method can measure not only AC loss in superconducting magnet but losses in conducting, radiant and low temperature. Consequently it is thought that efficient design and fabrication of superconducting magnet system will be possible by means of AC loss measurement method using calorimetric method.

• Journal of Radiation Industry
• /
• v.3 no.1
• /
• pp.7-11
• /
• 2009

Hard magnet was usually used by coating $SiO_2$ ceramic thick films followed by the thermal annealing process. In this work, the alternative annealing process for NdFeB magnets using e-beam sources (1~2 MeV, 50~400 kGy) was investigated. NdFeB magnets was coated with ceramic thick films using the spray method. The optimal annealing parameter for e-beam source reveals to be 1 MeV and 300 kGy. The sample prepared at 1 MeV and 300 kGy was characterized by the analysis of the surface morphology, film hardness, adhesion and chemical stability. The mechanical property of thick film, especially film hardness, is better than that of thermal annealed samples at $180^{\circ}C$. As a result, e-beam annealing process will be one of candidate and attractive heat treatment process. In future, manufacturing process will be carried out in cooperation with the magnet company.

• Journal of the Korean Magnetics Society
• /
• v.4 no.3
• /
• pp.214-218
• /
• 1994

$Y_{3}Fe_{5}O_{12}$ based garnet films(thin or thick) offer a great promise for the application of microwave communication components. We investigated the magnetic and crystallographic preperties of $Y_{3}Fe_{5}O_{12}$ thick films prepared by KrF eximer laser ablation of a stoichiometric garnet target. It was possible to obtain almost epitaxially oriented films on $Al_{2}O_{3}$(1102) plane. Although the crystalline quality depends on substrate temperature and $O_{2}$ partial pressure used($Po_{2}$), 4.1m thick films of $4{\pi}M_{s}=1300$ Gauss and $H_{c}=37.5$ Oe were obtained at the substrate temperature of $700^{\circ}C$ with the $Po_{2}$ of 100 mTorr after annealing the as-deposited films at $700^{\circ}C$ for 2 hours. These films are expected to be used for magnetostatic spin wave filters at narrow bandwidth frequency.

• Journal of Practical Engineering Education
• /
• v.15 no.1
• /
• pp.127-132
• /
• 2023

Authors report the performance indicator of Roll to Roll MC (hereinafter referred to as RTR) through experiment that it is possible to process 2.0G acceleration, which cannot be coped with in the existing FPCB RTR, by reducing the weight of the Dancer roll system and controlling the torque using the servo motor. Proposed dancer roll system provides uniform tension to FPCB by solving problems such as high rotation speed, heat generation, and low torque, which were impossible to achieve with the conventional magnet clutch type RTR. Through the development of a lightweight processing method for rolls using magnesium material and the development of a torque control algorithm for servo motor, torque stability also increased. Due to the enabling technology developed in this study, the reaction speed of the dancer roll was improved and the target speed was achieved as well.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.1
• /
• pp.9-16
• /
• 2016

A position control system composed of the PMLSM(Permanent Magnet Linear Synchronous Motor), unlike conventional linear permanent magnet synchronous motor is fixed to the permanent magnet moving coil rails (permanent magnet = stator, coil = mover), the coil is fixed, moving the permanent magnet, we propose a position control system (permanent magnet = mover, coil = stator) structure. Position is measured not using conventional encoder or resolver but by adopting vector control method using 2 hall sensors generating rectangular signal. This method estimate the velocity and position of mover by using the quadruple of two hall sensor signal instead of encoder signal. Vector control of PMLSM using 2 hall sensor generating rectangular wave is proved to control the system stable and efficiently through simulation. Also hardware experiment reveals that the position control performance is measured within the range of $30{\sim}50{\mu}m$ in the accuracy of $10{\sim}20{\mu}m$, which is improved twice to the conventional method. The proposed method exhibits its economical efficiency and practical usefulness. The vector control technique using two hall sensors can be installed in narrow place, accordingly it can be implemented on the system where the conventional encoder or resolver cannot operate.

• Journal of Energy Engineering
• /
• v.23 no.3
• /
• pp.82-87
• /
• 2014

MLI(Multi-layer Insulation) is widely used to get highly insulating on cryogenic system in order to reduce heat loads. MLI for satellites thermal performance is changed by materials and laminated method. In this study, a composite multilayer insulation by application of heat stroage tank performance were compared with materials and laminated to change the way. Experimental methods of the KS C 9805 was used, the composite multilayer insulation and EPS was compared with the insulation performance. A method for analysis of experimental results is the equivalent thickness about CMI and the insulation performance were used to compare thermal conductance. As a results, the equivalnet thickenss and the thermal conductance of the composite multilayer insulation were smaller than the EPS and the thermal performance are more excellent. In addition, the configuration of the composite multilayer insulation materials and laminated method varies depending on the overall heat transfer coefficient was confirmed.

• Journal of the Korean Ceramic Society
• /
• v.39 no.10
• /
• pp.935-942
• /
• 2002

Gallium-doped ZnO (GZO) films were deposited on soda-lime glass substrate without heating using Ne, Ar, or Kr gas. Electrical properties of GZO films deposited at various total gas pressures were investigated for the film positions corresponding to the erosion region (region B) and outside the erosion region (region A) of the target. Region B showed high resistivity, which was attributed to the decrease in carrier density and Hall mobility, compared to region A. GZO films deposited using Ne gas showed the degradation in resistivity and crystallinity, whereas, GZO films deposited using Kr gas showed the improvement in resistivity and crystallinity. This degradation in film properties could be attributed to the film damage caused by the bombardment of high-energy particles. Especially, the energies of recoiled neutral atoms ($Ne^0,\;Ar^0,\;Kr^0$) calculated by Monte Carlo simulation corresponded to experimental results.