• Journal of the Korean Recycled Construction Resources Institute
• /
• v.10 no.3
• /
• pp.276-284
• /
• 2022

In this study, performance evaluation and rheological characteristics were analyzed for recycling the fine powder of nuclear power plant dismantled waste concrete as a solidifying agent for radioactive waste disposal. The radioactive concrete fine powder was used to prepare a simulated sample, and the test specimen was prepared using Di-water, CoCl₂, and 1 mol CsCl aqueous solution as mixing water. Regardless of the aggregate mixing ratio and the type of mixing water, it satisfies the performance standard of 3.45 MPa for compressive strength at 28 days of age. All specimens satisfied the criteria for submersion strength, and the thermal cycle compressive strength satisfies the criteria for all specimens except Plain-50. As a result of evaluating the rheological properties of the solidifying agent, it was found that the increase in the aggregate mixing rate decreased the yield stress and plastic viscosity. The leaching index for cobalt and cesium of all specimens was 6 or higher, which satisfies the standard. In order to secure the stable performance of the solidifying agent, it is considered effective to use 40 % or less of the aggregate component in the solidifying agent.

• Journal of the Korea Institute of Building Construction
• /
• v.8 no.2
• /
• pp.99-106
• /
• 2008

To improve concrete tensile strength and bending strength, New plan that have more economical and simple manufacture process is groped. By an alternative plan, chemical pre-stressed concrete is presented. In this study, we analyzed the rheological properties of cement paste with the kind and replacement ratio of k-type CSA type expansive additives that is used mainly in domestic. and we suggested that the algorithm of a mixing plan in the chemical pre-stressed concrete and from this, we presented the basic report for the right mixing plan. From the results, Flow increased more or less according to use of expansive additives. This phenomenon was observed by increasing paste amount that shows as substitution for expansive additives that specific gravity is smaller than that of cement. As linear regression a result supposing paste that mix expansive additives by Bingham plastic fluid. The shear rate and shear stress expressed high interrelationship. therefore, flow analysis of quantitative was available. The plastic viscosity following to replacement ratio of expansive additives is no change almost, the yield value is decreased in proportion to the added amount of expansive additives. Through this experiment, we could evaluate rheological properties of cement paste using the expansive additives. Hereafter by an additional experiment, we must confirm stability assessment of material separation by using the aggregate with the kind and replacement ratio of expansive additives.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.37 no.1
• /
• pp.37-42
• /
• 2011

The rheological properties of the aqueous solution of scleroglucan industrially produced by Sclerotium rolfsii at concentrations ranging from 0.1 % to 2 % (w/w) were determined by using brookfield viscometer and rheometer. Gel matrices of scleroglucans were stable over a wide range of pH and ionic strength in the aqueous medium. In the oil dispersion with phytosqualane in oil phase and three kinds of thickening agent in aqueous phase, scleroglucan showed the highest dispersion properties. The synergistic effect between scleroglucan and locust bean gum was also examined. The highest viscosity was obtained for the solution mixture at scleroglucan/locust bean gum weight ratio of 5 : 5. The results of this study suggest the potential of scleroglucan as thickner for a wide variety of cosmetic formulations.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2020.06a
• /
• pp.144-145
• /
• 2020

Recently, the cement industry has been using various wastes as raw materials and fuel for cement as an eco-friendly business. However, most of these waste resources contain large amounts of chloride and alkali, which are concentrated in manufacturing facilities and adversely affect cement production products. Accordingly, in the cement production process, the chlorine ion contained in cement is managed by introducing the Chlorine Bypass System (CBS) into the manufacturing facility and releasing the dust. However, the processing volume of CBS-Dust has been limited due to the shortage of domestic processing companies, and the cost has also been raised, requiring measures to be taken in dealing with CBS-Dust. In this study, rheological properties of CBS-Dust incorporated paste are tested. With the increase of CBS-Dust, flow was decreased due to enhanced viscosity.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.8
• /
• pp.5636-5645
• /
• 2015

Physical characteristics of aggregates affect the workability and strength of mortar and concrete, which include their fineness ratio, particle size distribution and water absorption. The workability of construction materials decreases if the incorporated fine aggregates show improper size distribution of their particles. This study shows the particle size effect on the rheological behavior of mortar and provides basic information for evaluating its workability. A mini-slump flow test was adopted to evaluate the workability of mortar. In addition, its plastic viscosity and yield stress were measured using a rheometer for building materials. The sand samples were prepared by sieving river sand and sorting out with their particle sizes. As a result, it was observed that the fines less than 0.7 mm increases the yield stress and plastic viscosity of the mortar samples. If the fines are less than 0.34 mm, the water absorption of the fines dominates change on the workability.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.3 no.2
• /
• pp.152-158
• /
• 2015

In order to investigate the feasibility of stone dust sludge as fine aggregate, an experimental study was performed on cement mortar with stone dust sludge. fresh mortar properties and strength with various stone dust sludge replacement ratios were estimated. the replacement ratio adopted in this study was 0, 10, 20, 30%. Flow, air content, and rheological properties were considered as properties of fresh mortar. Compressive strength and flexural tensile strength were measured for strength. The results are as follows. Higher amount of stone dust sludge caused reduction in slump and air content. In the rheological properties, both yield stress and plastic viscosity increased as stone dust sludge content increased up to 20% replacement ratio, but there were no remarkable difference between 20 and 30%. Yield stress increased drastically between 10 and 20%. Compressive and flexural tensile strength results indicated that the strength variation was not significant according to stone dust sludge content, but the strength gain in the early age by adding stone dust sludge was evident. the strength at the age of 28 days however did not show noticeable effect of adding stone dust sludge.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.25 no.6
• /
• pp.193-198
• /
• 2021

In this study, the rheological characteristics and of 3D printing composite materials and the compressive strength characteristics according to the lamination patterns were evaluated. As a result of rheology test, rapid material change was observed after 60 minutes of extrusion, yielding stress 1.4 times higher than immediately after mixing, and plastic viscosity was 14.94-25.62% lower. The compressive strength of the specimens manufactured in the mold and the laminated specimens were compared, and the lamination pattern of the laminated specimens were 0°, 45°, and 90° as variables. The compressive strength of the mold casting specimen and the laminated specimen from 1 to 28 days of age showed similar performance regardless of the lamination pattern. In particular, at the age of 28 days, the modulus of elasticity, maximum compressive strength, and strain at maximum stress of all specimens were almost the same. In order to analyze the interface of the laminated specimens, X-ray CT analysis of the specimen whose compressive strength were measured was performed. Through CT analysis, it was confirmed that cracks did not occur at the lamination interface, which can be judged that the interface in the laminated specimen behaved in an integrated manner.

• Korean Journal of Food Science and Technology
• /
• v.35 no.1
• /
• pp.44-51
• /
• 2003

찹쌀가루와 메주가루의 배합비율(무게비)을 달리한 고추장(찹쌀가루 : 메주가루 = 1:1, 1:2, 1:3, 2:1, 3:1)의 숙성 중 품질 변화를 평가하기 위해 12주 동안 숙성시키면서 고추장의 이화학적 특성, 효소 활성 및 레올로지 특성을 연구하였다. 숙성 중 고추장의 수분함량은 $47.4{\sim}47.9%$에서 점차 증가하여 8주에는 최대 수분함량을 보였다. 환원당 함량은 $2{\sim}4$주에 가장 높았으며 이후에서는 점차 감소하는 경향을 보였다. 아미노태 질소 함량은 지속적으로 증가하였다. ${\alpha}-amylase$와 ${\beta}-amylase$ 활성은 숙성 $2{\sim}4$주에 최대 역가를 나타냈다. Acidic protease와 neutral protease는 각각 숙성 2주와 4주에 가장 높은 활성을 보였다. Power law 모델에 의한 유동성 측정에서 고추장은 낮은 유동성지수(flow behavior index, $n=0.21{\sim}0.36$)를 가진 전단담화(shearing-thinning)거동을 보여주었으며, 점조도 지수(consistency index, K)와 겉보기점도 $({\eta}_{a,10})$는 숙성 2주에 급격히 증가하고 이후에는 감소하였다. Casson 모델식에 의한 항복응력$({\sigma}_{oc})$은 숙성 2주에 급격히 증가하고 이후에는 감소하였다. 동적 점탄성 측정에서는 저장 탄성률 (G#)이 손실탄성률 (G') 보다 높은 수치를 나타내었고 주파수(frequency, ${\omega}$)가 증가함에 따라 증가하는 경향을 보여주었다. 또한 숙성기간이 경과함에 따라 (G#)과 (G@)이 증가하는 경향을 나타냈다.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.05a
• /
• pp.301-306
• /
• 2001

This study was _ performed of rheological properities for slurry of ultra fine cement using admixtures. An experimental parameter is W/B and superplasticizier ratio and different water-soluble polymers. As a results, it's strongly appeared to rheological properties of slurry as particles ratio, it's know that rheological properities affected by admixtures.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.392-393
• /
• 2006

Direct Printing Process is a suitable fabrication technique to develope pigment components whose dimensions are in nano. The success of this process depends on the sysmatic preparation of pigment millbase. Conventional millbase dispersions are constituted of the organic pigments, monomer, dispersant and solvents. An experimental study on the rheology of millbase dispersions is presented.