• 한국분무공학회지
• /
• 제16권3호
• /
• pp.119-125
• /
• 2011

Due to the oxygen contents in biodiesel, application of the fuel to compression ignition engines has significant advantages in terms of lowering PM formation in the combustion chamber. In recent days, considerable studies have been performed to extend the low temperature combustion regime in diesel engines by applying biodiesel fuel. In this work, low temperature combustion characteristics of biodiesel blends in dilution controlled regime were investigated at a fixed engine operating condition in a single cylinder diesel engine, and the comparisons of engine performances and emission characteristics between biodiesel and conventional diesel fuel were carried out. Results show that low temperature combustion can be achieved at $O_2$ concentration of around 7~8% for both biodiesel and diesel fuels. Especially, by use of biodiesel, noticeable reduction (maximum 50% of smoke was observed at low and middle loads compared to conventional diesel fuel. In addition, THC(total hydrocarbon) and CO(Carbon monoxide) emissions decreased by substantial amounts for biodiesel fuel. Results also indicate that even though about 10% loss of engine power as well as 14% increase of fuel consumption rate was observed due to lower LHV(lower heating value) of biodiesel, thermal efficiencies for biodiesel fuel were slightly elevated because of power recovery phenomenon.

• 한국분무공학회지
• /
• 제25권4호
• /
• pp.178-187
• /
• 2020

The current emission regulations, US Tier-4 and EU Stage-V, are only able to satisfy the regulations when all currently mass-produced emission reduction technologies such as EGR, DOC, DPF, and SCR are applied. Therefore, in this study, for the application of the Urea-SCR system to non-road diesel engines, the database was established by measuring the NO, NO2 concentration and calculating the NO2/NOx ratio based on the catalyst temperature and exhaust mass flow rate. Also, based on the measured NO2/NOx ratio data, a mathematical model was proposed to predict the NO2/NOx ratio at SCR catalyst, and the suitability of the model was verified through steady-state and transient mode. As a result of comparing the NO2/NOx ratio measured at the DOC outlet under the steady-state condition to two model values separately, the R2 was 0.9811 for the 3D map model and 0.9303 for the mathematical model. And in the case of the NO2/NOx ratio measured at the DPF outlet, the R2 was 0.9797 for the 3D map model and 0.935 for the mathematical model. It was confirmed that the R2 with the model value of the 3D Map of the mathematical model in the transient mode is 0.957, which shows high reliability.

• 대한환경공학회지
• /
• 제22권10호
• /
• pp.1825-1832
• /
• 2000

유류화합물(디젤)로 오염된 불포화층 토양에 대한 현장오존복원공정의 기초연구로, 토양조건에 따른 오존의 이동과 분해, 디젤과의 반응경향을 조사하였다. 건조상태에서 유기물을 제거한 모래와 glass beads 충진컬럼에서 기상 오존의 분해를 조사한 결과 일차반응으로 가정시 반응 속도상수값(k)이 각각 $9.9{\times}10^{-3}s{^{-1}}$와 $4.3{\times}10^{-4}s{^{-1}}$로 나타나 모래의 경우 철 (Fe), 망간(Mn) 성분 등의 촉매작용으로 25배 가량 반감기가 짧은 것을 확인할 수 있었다. 디젤로 오염시킨 현장 토양과 모래를 컬럼에 충진하여 동일조건하에서 오존주입시 토양입자의 크기와 유 무기물의 함량 차에 의한 오존이동상에 지체효과 및 소모량의 차이를 관찰하였고, 50mL/min의 유속에서 공기만을 주입시 DRO(diesel range organic) 기준 초기 디젤총량($800{\pm}50mg/kg$)의 30%가 제거된데 비해 오존을 6mg/min으로 16시간 주입한 결과 각각 80% 이상이 제거되었다. 오존주입시간에 따라 컬럼의 유출 입부에 잔류하는 TPH(total petroleum hydrocarbon)와 DRO 중 aliphatic계열 8개 물질들의 농도를 비교/분석한 결과, 낮은 탄소수 물질들로의 전환과정을 거쳐 유체의 흐름에 따라 컬럼 밖으로 이동됨을 확인하였고, 토양내 수분함량은 오염 토양복원에 오존을 적용시 중요한 인자임을 확인하였다.

• 한국입자에어로졸학회지
• /
• 제13권3호
• /
• pp.105-110
• /
• 2017

본 연구에서는 고온희석-상온희석 2단 희석의 다공 튜브형 희석장치를 제작하여 실제 배기가스와 시험챔버의 다양한 고수분 환경에서의 희석 조건에 따른 응축성 물질의 생성 억제와 생성된 응축 입자의 제거 특성에 관하여 살펴보았다. 디젤 엔진의 배출 입자는 응축 성분의 핵화 모드와 고체상의 응축성장 모드의 이중모드 분포를 나타내었고, 다공 튜브형 희석장치의 1차 고온희석 유량을 증가시킴으로써 핵화 모드 입자의 생성을 억제시키고 응축성장 모드의 입자만을 측정할 수 있었다. 석탄보일러에서 배출되는 미세먼지에 대해서도 다공 튜브형 희석장치를 적용하여 응축성 성분의 입자 생성 없이 응축성장 모드의 입자만을 측정할 수 있었고, $3{\mu}m$ 크기 이상의 입자에 대해서 기존 이젝터 방식에 비해 상대적으로 입자 손실이 적음을 확인할 수 있었다. 또한 $30m^3$ 시험챔버에서 가습기로 인위적으로 발생시킨 물입자가 측정하고자 하는 고체 입자와 공존할 때 다공 튜브형 희석장치를 사용하여 물입자를 증발시켜 제거함으로써 고체 입자만을 정확하게 분리하여 측정할 수 있음을 확인할 수 있었다.

• Korean Chemical Engineering Research
• /
• 제57권4호
• /
• pp.584-588
• /
• 2019

디젤엔진 시스템은 미세먼지 배출의 엄격해진 저감/제어 기준을 충족하기 위해서 산화촉매는 매우 중요한 기술 중에 하나이다. 본 연구에서는 효율적인 soot산화의 촉매로 Ag 나노입자가 loading된 $La_{0.6}Sr_{0.4}Co_{0.2}Fe_{0.8}O_3$ 섬유상 web 촉매를 제시하였다. 제조된 촉매는 FE-SEM, EDS mapping, XRD, XPS 분석을 통해 특성을 평가하였다. Soot 산화성능측정결과 Ag의 효율적인 촉매특성과 증가된 soot입자와 표면의 접촉면적으로 인하여 50% 산화온도 평가($T_{50}=490^{\circ}C$)에서 자연적인 산화보다 $151^{\circ}C$ 가속화된 것을 확인하였다. 따라서 Ag가 loading된 촉매와 3차원적인 web 구조는 soot 산화에 효율적인 촉매후보군으로 확인하였다.

• 한국대기환경학회지
• /
• 제19권3호
• /
• pp.297-306
• /
• 2003

Works were focused on back pressure characteristics of ceramic fiber filter on DPF (Diesel Particulate Filter) system and experiments were performed to select appropriate filter which can filter particulates. Filters were installed on metal -support tube which has openings for exhaust gas flow. Ceramic fiber filters with high specific surface area and adequate high temperature strength are commercially available for filtration of diesel particulates and in -situ hot regeneration. Thus, ceramic blanket and ceramic board which are used as insulating media were applied to filter and filtration apparatus was installed on exhaust gas line connected to 2.0 L diesel engine. Alternating filter structure to adapt DPF system, collection efficiency test of diesel particulates was measured. In case of ceramic blanket, pressure drop was low, caused by the destruction of soft structures. Also, particulate collection efficiency was decreased depending on loading time. In case of ceramic board, structure design was altered to reduce back pressure on DPF system. Structure design was altered to induce Z-flow by making 10 mm and 5 mm holes on the surface of media. Alteration of 5 mm hole showed that media have low back pressure but particulate collection efficiency was 77%, while 10 mm hole showed that of 90%.

• 환경위생공학
• /
• 제17권2호
• /
• pp.11-17
• /
• 2002

Diesel particulate matter (DPM) is known to be one of the major harmful emissions produced by diesel engines. The majority of diesel particles are in the range of smaller than $I{\mu}\textrm{m}$. Because of their tiny volume, ultrafine diesel particles contribute very little to the total mass concentration which is currently regulated for automobile emissions. Diesel particles are known to have deleterious effects upon human health because they penetrate human respiratory tract and have negative effects on the health. The measurement of the number distribution of nanometer size particles (nanoparticles) in the diesel exhaust emission is important in order to evaluate their environmental and health impact, and to develop new types of diesel particulate filters. In this study, we directly sampled particulate matters emitted from a diesel truck mounted on the chassis dynamometer by a flow separator and dilution system, and measured the nanoparticles using two types of differential mobility analyzers combined with a Faraday cup electrometer (FCE) and a condensation particle counter (CPC). The particle size distributions were analyzed by changing engine operation condition, i.e. ratio of engine loading. The total number concentration of particles were increased with the engine loading ratio and the nanoparticles (less than 50nm) were affected by hydrocarbon (HC) concentration in the diesel exhaust.

• 한국산업보건학회지
• /
• 제23권4호
• /
• pp.323-332
• /
• 2013

Objectives: This study was conducted in order to investigate the diesel exhaust particle(DEP) concentrations in the thirteen parking lots of large shopping complex. Methods: The real-time black carbon(BC) concentration was determined using an Aethalometer, and elemental/organic carbon concentration was determined according to the method of the National Institute for Occupational Safety and Health(NIOSH) 5040. The particle number concentration(NC), lung deposited surface area concentration(LDSA) and geometric mean diameter(GMD) were determined using a DiSCmini aerosol monitor. Results: The average concentration of BC, EC, OC, NC, LDSA and GMD were $19.1{\mu}g/m^3$, $12.6{\mu}g/m^3$, $51.5{\mu}g/m^3$, $94,000particles/cm^{-3}$, $298{\mu}m^2/cm^{-3}$ and 57 nm in all parking lots, respectively, approximately 3-fold higher than those found in the urban outdoor. The average concentration of BC were $21.3{\mu}g/m^3$ in underground parking lots, 3-fold higher than above parking lots. Conclusions: Therefore, the parking lots at the large shopping complex can be considered a potentially dangerous environment with a high concentration of DEP nanoparticles.

• 한국자동차공학회논문집
• /
• 제9권2호
• /
• pp.35-42
• /
• 2001

The diesel engine exhaust gas is know as one of the causes to produce photochemical smog, which causes damage on environmental. However, due to the high thermal efficiency and low carbon dioxide emission, the usage of a diesel engine is prevailed. In this study, the DC non-thermal plasma technology used to the particulate matter (PM) aftertreatment. The exhaust gas characteristics and energy density were investigated on the dynamometer test bed and chassis dynamometer with CVS-75 mode in a passenger diesel car. It was reported that the smoke removal efficiency has around the 70% in the dynamometer test with 80W energy consumption and the PM removal efficiency has the 68% in the real car test. The NOx also reduced the 20% according to electrode type respectively. Considering these results, plasma technology is one of the ways to simultaneously removing method the particulate matter (PM) and NOx.

• 한국자동차공학회논문집
• /
• 제14권3호
• /
• pp.75-80
• /
• 2006

Since air pollution has become a globally critical issue and exhaust emissions from automobiles cause a major source of air pollution, many countries including advanced countries have stipulated stringent emission regulations. Particularly in diesel vehicles, NOx and particulate matters exhaust in significant amounts even though diesel vehicles provide merits in aspects of higher thermal efficiency and lower $CO_2$. To reduce Particulate matters and NOx, after-treatment technology such as filter trap, oxidation catalysts and EGR has been applied. This test was conducted on the effect of continuous regeneration diesel particulate filter and cooled-EGR, and 15ppm low sulfur diesel was used as a test fuel. Exhaust emissions, PM, NOx, CO, HC and Soots were measured and compared under D-13 and D-3 modes.