• Journal of the Mineralogical Society of Korea
• /
• v.17 no.4
• /
• pp.327-338
• /
• 2004

XRD studies on annealed Na-feldspar (Amelia albite) at $1100^{\circ}C$ showed rapid structural changes due to Si-Al disordering, which resulted in phase transformations from low albite to high albite by 4-days annealing test. TEM SAED analyses on the annealed samples revealed a trend of structural changes, but estimation of the structural state was difficult due to a large deviation of the SAED data. Optimum conditions of CBED analyses on albite was established by employing a cooling specimen holder, 120 kV of acceleration voltage, 37 Jim of condenser aperture size and 25 nm of spot size. A proper orientation showing distinct changes of HOLZ lines corresponding to the structure changes of albite turned out to be close to the [418] direction with $-1.2^{\circ}$ tilting, where the width of two HOLZ lines in low albite was opposite to those in high albite.

• Korean Chemical Engineering Research
• /
• v.44 no.6
• /
• pp.644-649
• /
• 2006

In this paper, the Cr(VI) adsorption behaviors of activated carbons (ACs) treated by various ozone treatment conditions were studied. The surface properties of the ACs studied were determined by pH, acid-base, and FT-IR measurements. $N_2$ adsorption isotherm characteristics at 77K were confirmed by BET equation, Boer's t-plot method, and Horvath-Kawazoe's slit pore model. Also, the total Cr adsorption amount onto the ACs was measured by ICP-AES. As a result, the ozone treatment led to an increase of oxygen-containing polar functional groups and total acidity as well. Meanwhile, the specific surface areas or micropore volumes were slightly decreased after the ozone treatment due to the micropore filling or blocking. Nevertheless, the total Cr adsorption of ACs was increased with increasing of the ozone treatment time, attributed to the good interaction between Cr ions and polar functional groups on the ACs.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.1
• /
• pp.136-142
• /
• 2007

Recent publications have paid attention on the utilization of solid reagents for the removal of substances causing eutrophication, in particular $PO_4^{3-}$ ions. The adsorption of dissolved inorganic phosphate on slag produced by the refining process of iron ore was fundamentally studied for suppressing the liberation of phosphate from wastewater. This study has been conducted in order to find a possibility to improve the phosphate removal and to evaluate the phosphate removal variation to form hydroxyapatite, when the converter slag is used for phosphate removal. The result shows that the converter slag can be applied to remove phosphate using Freundlich isotherm. The size of converter slag, $2{\sim}0.425 mm$ was more efficient than $2{\sim}4.75mm$ to remove phosphate. In particular, 1 mg/L of phosphate can be removed up to 80% of the initial concentration for the continuous column experiment.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.12 no.1
• /
• pp.25-30
• /
• 1976

In the area of the Far East Asia, cyclones are observed 157ea in winter season during the years(1966-1974). Some of them are most difficult to be forecasted due to the extreme irregulalities, have carried out synoptic analysis. The rapid development of cyclones can be attributed to the descending of cold air mass surrounding the axis of the Jet Stream due to the cyclonic rotation, and the lowering of the Jet axis. The Relationships between upper trough line and max. (or min) axis of upper air temperature on the 700mb contributes to the development of the cyclones.

• Resources Recycling
• /
• v.28 no.2
• /
• pp.54-61
• /
• 2019

In order to recover pure alumina from black dross, leaching of mechanically activated black dross with NaOH solution resulted in an aluminate solution containing a small amount of Si(IV). Selective adsorption of Si(IV) onto hydrotalcite was investigated from 5 M NaOH solution where the concentration of Al(III) and Si(IV) was 13000 and 150 mg/L, respectively. Only Si(IV) was selectively loaded onto hydrotalcite, while Al(III) remained in the solution. Effect of the calcination treatment of hydrotalcite and concentration of calcined hydrotalcite and NaOH on the loading of Si(IV) was investigated. Although the loading percentage of Si(IV) was low from 5 M NaOH solution, most of the Si(IV) was removed by adjusting the concentration of NaOH by 48 times dilution with water when the concentration of calcined hydrotalcite was higher than 4.5 g/L. The loading of Si(IV) onto calcined hydrotalcite followed Freundlich adsorption isotherm.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.33 no.6
• /
• pp.282-287
• /
• 2023

The effect of stress relief heat treatment temperature and duration time on the microstructure, residual stress and Vickers hardness of additively manufactured Ti-6Al-4V alloy using laser powder bed fusion process was clarified. As a result of stress relief heat treatment for 240 minutes at 823 K and 60 minutes or more at 873 K, residual stress was decreased less than 30 MPa without grain growth and phase transformation which causes dimensional distortion and deterioration of mechanical properties. In addition, hardness was increased with increasing heat treatment temperature and duration time. It was deduced that the refinement of acicular martensitic α' phase due to the increasing duration time of isothermal heat treatment at 773~873 K, which was not detected by XRD and phase map analysis using SEM-EBSD, probably increases the hardness.

• Korean Chemical Engineering Research
• /
• v.54 no.1
• /
• pp.81-88
• /
• 2016

Limonene is orange flavored natural material that is mainly contained in mandarine and lemon peels. D-limonene was extracted from cold-storaged mandarine peel by using Soxhlet extractor at $120^{\circ}C$ for 2 hours with ethanol as solvent. Henry constants of d-limonene and impurity were calculated as $H_{Lim}=8.55$ and $H_{imp}=0.223$ from the result of HPLC analysis. 4-bed SMB of limonene simulation with $0.46{\times}25cm$ columns was conducted by using Aspen chromatography program. Then effective condition for purity was found by changing $m_2$ and $m_3$ values in triangle diagram. The highest purity was 98.59% at $m_2=2.57$, $m_3=9.55$. For this case, feed, desorbent, extract, and raffinate flow rates were 1 mL/min, 1.19 mL/min, 0.857 mL/min and 1.34 mL/min, respectively. Scale-up simulation was also conducted by increasing column diameter from 0.46 cm to 1.6 cm for getting the same efficiency. The increased flow rates were 12 mL/min, 14 mL/min, 10 mL/min, and 16 mL/min for feed, desorbent, extract, and raffinate. It was possible to scale-up with maintaining same limonene purity because linear isotherms of limonene and impurity were assumed.

• Korean Chemical Engineering Research
• /
• v.50 no.5
• /
• pp.866-873
• /
• 2012

IgY (Immunoglobulin Yolk) is a specific antibody in egg yolk, and it protects human body from virus and antigen. There are a lot of egg yolk components such as lipoprotein and protein. To separate IgY, HPLC (High Performance Liquid Chromatography) and precipitation were used in a batch mode and SMB (Simulated Moving Bed) was adopted for continuous purification of yolk proteins. IgY and other proteins in yolk were separated by using three-zone and four-zone SMB chromatography. Before performing SMB experiments, batch chromatography simulation parameters and adsorption isotherms were obtained. The parameters of batch chromatography were used to simulate SMB using Aspen chromatography. To compare three-zone and four-zone SMB chromatography, simulations in $m_2-m_3$ plane on the triangle theory were carried out. In terms of concentration and purity of both IgY and other lipoproteins, 3-zone SMB process is considered as ideal at the vertex of triangle ($m_2$, $m_3$=0.1, 1.1). 4-zone SMB yields the highest IgY purity at the coordinate ($m_2$, $m_3$=0.06, 0.5), which is the pure raffinate region. In 3-zone SMB without recycle, other lipoproteins in extract are largely affected in purity by small shift from the vertex of triangle ($m_2$, $m_3$=0.1, 1.1).

• Korean Chemical Engineering Research
• /
• v.52 no.6
• /
• pp.807-813
• /
• 2014

The Ag-impregnated activated carbon was produced from bamboo activated carbon by soaking method of silver nitrate solution. The carbonization and activation of raw material was conducted at $900^{\circ}C$. Soaking conditions are the variation of silver nitrate solution concentration (0.002~0.1 mol/L) and soaking time (maximum 24 h). The specific surface area and pore size distribution of the prepared activated carbons were measured. Also, NO and activated carbon reaction were conducted in a thermogravimetric analyzer in order to use for de-NOx agents of used activated carbon. Carbon-NO reactions were carried out with respect to reaction temperature ($20{\sim}850^{\circ}C$) and NO gas partial pressure (0.1~1.8 kPa). As results, Ag amounts are saturated within 2h, Ag amounts increased 1.95 mg Ag/g (0.2%)~ 88.70 mg Ag/g (8.87%) with the concentration of silver nitrate solution in the range of 0.002~0.1 mol/L. The specific volume and surface area of bamboo activated carbon of impregnated with 0.2% silver were maximum, but decreased with increasing Ag amounts of activated carbon due to pore blocking. In NO reaction, the reaction rate of impregnated bamboo activated carbon was retarded as compare with that of bamboo activated carbon. Measured reaction orders of NO concentration and activation energy were 0.63[BA], 0.69l[BA(Ag)] and 80.5 kJ/mol[BA], 66.4 kJ/mol[BA(Ag)], respectively.

• Journal of the Korean Wood Science and Technology
• /
• v.36 no.6
• /
• pp.1-12
• /
• 2008

A series of the studies on the applied physical properties of domestic species have been conducted last three years. Liriodendron tulipifera, Betula costata, Paulownia coreana were examined on sorption property, thermal property, electric property, acoustic property. Because the same apparatus and experimental procedures were used for all species, their results can be easily comparable. The experiments for sorption property were conducted with 80 mesh wood powder and resulted in their EMC's and sorption isotherms. The thermal conductivity and diffusivity, and electric resistance and volumetric electric resistivity were measured with a thermal-wire device and a high electric resistance meter. The differences of the thermal and electric properties between quarter-and flat-sawn specimens were observed, which was partially attributed to their anatomical differences. An acoustic measurement system was used to evaluate dynamic MOE and internal friction. This paper provides the useful fundamental data for designing a wood structure, correcting a portable resistance-type moisture meter, and acoustic properties of wood.