• Proceedings of the KWS Conference
• /
• 2001.05a
• /
• pp.192-194
• /
• 2001

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.1
• /
• pp.198-203
• /
• 2000

In this paper, a numerical analysis is carried out to show the effect of friction farce on the dynamic characteristics of a flow divider valve. The continuity equations and the equation of motion fur spool are numerically solved. The viscous friction force acting on the spool is considered analyzing the Reynolds equation which governs the viscous flow in the clearance gap between the spool and sleeve. Dynamic characteristics are highly affected by the viscous friction farce whose magnitude is relatively small compare with other fluid forces. Therefore present theoretical formulation and numerical scheme can be used generally in designing and performance evaluation of all the hydraulic spool valve.

• Journal of Welding and Joining
• /
• v.15 no.4
• /
• pp.90-98
• /
• 1997

A copper-tungsten sintered alloy(Cu-W) has been friction welded to a tough pitch copper in order to investigate the effect of friction pressure on bonding strength and a charicteristic of fracture. The tensile strength of the friction welded joint was increased up to 90% of the Cu base metal under the condition of friction time 1.2 sec, friction pressure 4.5kgf/$\textrm{mm}^2$ and upset pressure 10kgf/$\textrm{mm}^2$. From the results of fracture surface analysis, the increase of friction pressure could remarkably decrease the force and the time to be normally acted on weld interface. The W particles which were included in the plastic zone of Cu side could induce fracture adjacent to the weld interface because their existance in Cu induces a decrease in available section area and an increase in notch effect. Therefore, the tensile strength was decreased at high friction pressure (6kgf/$\textrm{mm}^2$) because the destruction of W was increased by an increase in mechanical force and crack was formed at weld interface.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.4
• /
• pp.1611-1617
• /
• 2013

Information about trafficability or the condition of road with regard to its being traveled over by vehicles is one of the most critical factors for roadway operation in winter. Specifically, when traveling on snowy or icy surfaces, the traction force varies per vehicle type including tire types, geometric characteristics of roads, and conditions of road surfaces. In general, front-wheel drive or four-wheel drive vehicles have better traction performance on snowy or icy surface than rear-wheel drive vehicles, and the latter type vehicle causes more serious traffic congestion when there is unexpected snowfall. Thus, traffic information regarding trafficability with respect to vehicle types, geometric characteristics of roadway sections, and roadway surface conditions can provide a foundation to make a decision whether to use the associated roadway sections for roadway operators as well as users. Based on the preceding premise, the objective of this study is to present a methodology for developing a trafficability index with respect to vehicle types, geometric characteristics of roadway sections, and roadway surface conditions.

• Tunnel and Underground Space
• /
• v.16 no.1 s.60
• /
• pp.58-72
• /
• 2006

In recent years, not only the occurrences but the magnitude of earthquakes in Korea are on an increasing trend and other sources of dynamic events including large-scale construction, operation of hi띤-speed railway and explosives blasting have been increasing. Besides, the probability of exposure fir rock joints to free faces gets higher as the scale of rock mass structures becomes larger. For that reason, the frictional behavior of rock joints under dynamic conditions needs to be investigated. In this study, a shaking table test system was set up and a series of dynamic test was carried out to examine the dynamic frictional behavior of rock joints. In addition, a computer program was developed, which calculated the acceleration and deformation of the sliding block theoretically based on Newmark sliding block procedure. The static friction angle was back-calculated by measuring yield acceleration at the onset of slide. The dynamic friction angle was estimated by closely approximating the experimental results to the program-simulated responses. As a result of dynamic testing, the static friction angle at the onset of slide as well as the dynamic friction angle during sliding were estimated to be significantly lower than tilt angle. The difference between the tilt angle and the static friction angle was $4.5\~8.2^{\circ}$ and the difference between the tilt angle and the dynamic friction angle was $2.0\~7.5^{\circ}$. The decreasing trend was influenced by the magnitude of the base acceleration and inclination angle. A DEM program was used to simulate the shaking table test and the result well simulated the experimental behavior. Friction angles obtained by shaking table test were significantly lower than basic friction angle by direct shear test.

• Proceedings of the KWS Conference
• /
• 2000.04a
• /
• pp.95-96
• /
• 2000

• Journal of Institute of Control, Robotics and Systems
• /
• v.3 no.5
• /
• pp.476-481
• /
• 1997

본 논문에서는 비구동 관절을 가지는 2링크 매니퓰레이터의 동력학 해석과 운동제어를 제1적분을 기초로 하여 전개하고 있다. 매니퓰레이터의 운동이 제1적분의 적분상수에 의해서 기술되는 것을 보이고, 제1적분을 이용하여 매니퓰레이터의 동력학을 해석하고 있다. 그리고 해석된 동력학을 적극적으로 이용하는 운동제어 알고리즘을 구성하고 시뮬레이션을 통하여 확인하고 있다. 끝으로 비구동 관절에 마찰이 작용하는 경우, 브레이크등의 보조수단을 이용하지 않고도 매니퓰레이터의 제어가 가능함을 보이고 있다.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.12 no.11
• /
• pp.904-913
• /
• 2002

In this study, a dynamic analysis of the reciprocating compression mechanism considering viscous friction force of a piston used in small refrigeration compressors is performed. The length of cylinder in this class of compressors is shortening to diminish the frictional losses of the piston-cylinder system. So, the contacting length between piston and cylinder liner is in variable with the rotating crank angle around the BDC of the reciprocating piston. In the problem formulation of the compression mechanism dynamics, the change in bearing length of the piston and all corresponding viscous forces and moments are considered in order to determine the trajectories of piston and crankshaft. The piston orbits for viscous friction model and Coulomb friction model were used to compare the effect of the friction forces of piston on the dynamic trajectories of piston. To investigate the effect of friction force acting on the piston for the dynamic characteristics of crankshaft, comparison of the crankshaft loci is given in both viscous model and Coulomb model. Results show that the viscous friction force of piston must be considered in calculating for the accurate dynamic characteristics of the reciprocating compression mechanism.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.3 s.174
• /
• pp.786-793
• /
• 2000

Nylon, Polyacetal and PTFE were studied to gain a better understanding of their tribological behavior. Wear tests were conducted with reciprocating motion under dry sliding conditions. Friction coefficient and specific wear rate were measured as a function of sliding distance. The worn surfaces were examined with a Scanning Electron Microscope(SEM). Polyacetal showed lowest specific wear rates and PTFE exhibited lowest friction coefficient. The dominant wear mechanism found were adhesion and abrasion.

• Proceedings of the KSME Conference
• /
• 2001.06a
• /
• pp.674-679
• /
• 2001

For a large deformation nonlinear dynamic analysis of two-dimensional frictional contact, the linear complementarity formulation combined with a linearization is used. The solution procedure is based on the total Lagrangian formulation with a predictor and corrector scheme. For contact searching, a hierarchical scheme with a circular territory is used. A second-order approximation of displacements is used to detect impact time and position. The formulation is illustrated by means of numerical examples.