• Korean Journal of Optics and Photonics
• /
• v.17 no.1
• /
• pp.99-103
• /
• 2006

A tunable wavelength filter was proposed and demonstrated by using the UV nanoimprint technique. It consists of a Bragg grating in polymer waveguides and a heating electrode. The manufacturing of the grating was substantially simplified with the introduction of a smart imprint stamp containing a waveguide pattern integrated with the grating pattern. The center wavelength of the filter was successfully tuned by taking advantage of the thermooptic effect in polymers, which was induced by supplying electrical power to the electrode. For the fabricated device, a transmission dip of ${\~}$15 dB and a 3-dB bandwidth of 0.8 nm were obtained at the Bragg wavelength of ${\~}$l560 nm. The achieved thermooptic tuning efficiency was ${\~}$0.28 nm/mW, while the center wavelength was shifted from 1560 nm to 1558 nm with the electrical power consumption of 7 mW.

• Proceedings of the Optical Society of Korea Conference
• /
• 1991.06a
• /
• pp.22-22
• /
• 1991

광의 병렬처리 능력을 잘 활용한 1$\times$4 매트릭스 스위치의 구조와 전극구조를 설계하고 스위치 특성을 조사하기 위하여 beam propagation method(BPM)를 이용하여 수치계산을 하였다. 기존의 매트릭스 스위치는 대부분의 경우 방향성 결합기를 스위치 element로 이용하여 왔으나 이 결합기는 소자의 길이가 길기 때문에 단일 LinBO3 웨이퍼상에 집적할 수 있는 매트릭스 스위치의 크기가 제한되는 단점이 있다. 본 연구에서는 두 도파로 사이에 세 번째 도파로를 삽입하여 두 도파로를 결합시키는 세 도파로 결합기를 스위치 element로 사용하여 세 개의 스위치 element를 LiNbO3기판위에 직렬로 집적시킨 1$\times$4 매트릭스 스위치를 구성하였다. 스위치 element와 1$\times$4 매트릭스 스위치를 구성하였다. 스위치 element와 1$\times$4 매트릭스 스위치의 특성을 BPM을 사용하여 수치계산할 때 단일 모드 도파로의 유효 굴절을 분포는 n(X) = nm + $\Delta$ncosh-2(2x/w)의 형태로 가정했으며, 사용된 파라미터의 값은 각각 nm=2.1455, $\Delta$n=0.003, W=5$mu extrm{m}$, d=5$\mu\textrm{m}$, λ=1.3$\mu\textrm{m}$ 이고 S-파라메터의 값은 0.95927이므로 단일 모드 도파로가 된다. 계산결과 스위치 element의 결합길이는 3810$\mu\textrm{m}$이며 도파로의 길이가 결합길이와 같을 때 전극에 인가된 전압에 의한 도파로의 굴절을 섭등의 함수로 출력광의 세기를 계산한 결과 스위칭 전압은 14.85volt이고 crosstalk는 -18.9dB였다. 이 스위치 element로 구성된 1$\times$4 매트릭스 스위치는 스위칭 전압을 세 개의 전극에 적절한 조합으로 인가함으로써 한 입력 도파로에 결합된 광이 내개의 출력 도파로중 한 도파로에 스위칭 된다. 한편 수치계산의 결과를 실험적으로 확인하기 위해 스위치 element와 1$\times$4 매트릭스 스위치를 z-cut의 LinbO3 결정에 Ti을 열확산시켜 제작한 소자의 스위칭 특성을 발표할 예정이다.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.10
• /
• pp.1855-1861
• /
• 2017

In this paper, the gain enhancement of an SDPA using a director and two parasitic patches is studied. The modified balun is used to increase the bandwidth, whereas the director and two parasitic patches are appended to the SDPA to enhance the gain in the middle and high frequency bands. The effects of the distance between the director and parasitic patches on the antenna performance are analyzed, and the SDPA with a gain over 7 dBi at 1.54-2.99 GHz band is designed. The proposed SDPA is fabricated on an FR4 substrate with a dimension of $90mm(L){\times}135mm(W)$ in order to validate its performance. The fabricated antenna shows a frequency band of 1.56-3.10 GHz for a VSWR < 2, and it is confirmed by measurement that gain maintains over 7 dBi in the frequency range of 1.54-3.00 GHz.

• Korean Journal of Optics and Photonics
• /
• v.3 no.4
• /
• pp.244-251
• /
• 1992

Buried Bragg filters of single mode $Si_{3}N_{4}$ rib waveguide with a cover layer of $SiO_{2}$ and grating at the interface of $Si_{3}N_{4}$ and $SiO_{2}$ are designed and fabricated. Etching of the grating on $Si_{3}N_{4}$ waveguide core by buffered HF showed uniform etching with good control up to 1 nm. This buried type of Bragg filters are immune to contamination of the surface of device. The mode index and bandwidth of filters are determined by measurements of the transmission spectrum of Bragg filters and compared with that of calculation. Waveguide Bragg filters loaded with the micro-heater of Cr film and the cladding of silicone rubber are made to control the Brag wavelength of the filter. As a result the filter wavelength of the device moved by 0.41 nm for 10 mA current to the shorter side of wavelength proportional to the square of the current.

• Korean Journal of Optics and Photonics
• /
• v.26 no.6
• /
• pp.306-311
• /
• 2015

We report the characteristics of a single-wavelength-tunable fiber laser using a polymer waveguide Bragg grating (PWBG) wavelength filter. The output of the laser depends on environmental conditions, such as temperature and polarization states in the laser cavity. Wavelength tuning can be achieved, about 16.29 nm from 1548.24 nm to 1531.95 nm, according to the electric power applied to the PWBG wavelength filter. The achieved efficiency slope is about -0.16 nm/mW. A side-mode suppression ratio (SMSR) of more than 35 dB can be obtained by adjusting the polarization state in the laser cavity. A stable wavelength-tunable fiber laser can be achieved using the PWBG wavelength filter with a TEC module and a polarization-maintaining fiber.

• Korean Journal of Optics and Photonics
• /
• v.3 no.4
• /
• pp.258-265
• /
• 1992

A low loss optical waveguide of $P_{2}O_{5}-SiO_{2}$on Si substrate is produced by using the chemical vapour deposition method of $SiO_2$ thin films used in Si technology. Propagation loss of the waveguide layer was 1.65 dB/cm as produced and reduced down to 0.1 dB/cm after heat treatment at $1100^{\circ}C$. By using laser lithography and reactive ion etching method $P_{2}O_{5}-SiO_{2}$ waveguide was produced and subsequently annealed at $1100^{\circ}C$.As a result of this annealing the shape of the waveguide core was changed from rectangular to semi-circular form, and the propagation loss was reduced as down to 0.03 dB/cm at 0.6328$\mu$m and 0.04dB/cm at 1.53$\mu$m. We think that the mechanism of the reduction in propagation loss during the heat treatment is the following: 1) The hydrogen bonding in waveguide layer, which causes absorption loss, is dissociated and diffused out. 2) The roughness of the interface and the micro-structure of the waveguide layer is removed. 3) The irregularities in the cross-sectional shape of the waveguide which was induced during the lithographic process were disappeared by flowing of the waveguide core.

• Korean Journal of Optics and Photonics
• /
• v.16 no.4
• /
• pp.384-391
• /
• 2005

A polymer optical microring resonator, which is laterally coupled to a straight bus waveguide, has been proposed and demonstrated using a nanoimprint technique. The propagation loss of the ring waveguide and the optical power coupling between the ring and bus waveguides was calculated by using a beam propagation method, then the dependence of the device performance on them was investigated using a transfer matrix method. We have especially introduced an imprint stamp incorporating a smoothing buffer layer made of a silicon nitride thin film. This layer played an efficient role in improving the sidewall roughness of the waveguide pattern engraved on the stamp and thus reducing the scattering loss. As a result the overall Q factor of the resonator was greatly increased. Also it reduced the gap between the ring and bus waveguides effectively to enhance the coupling between them, without relying on the direct writing method based on an e-beam writer. As for the achieved device performance at the wavelength of 1550 nm, the quality factor, the extinction ratio, and the free spectral range were ~103800, ~11 dB, and 1.16 m, respectively.

• Proceedings of the Optical Society of Korea Conference
• /
• 2009.02a
• /
• pp.289-290
• /
• 2009

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.26 no.4B
• /
• pp.410-417
• /
• 2001

본 논문에서는 여러개의 WDM 채널을 동시에 처리할 수 있는 새로운 출력 공유버퍼를 제시했다. 분석을 통해 만약 버퍼에서 사용되는 광 도파로열 격자의 누화 값이 -33dB이하이며, ,BER 10-9의 시스템 성능을 만족하면서 8개 이상의 WDM 체널을 동시에 버퍼링할 수 있음을 보였다.

• Proceedings of the IEEK Conference
• /
• 1998.06a
• /
• pp.185-188
• /
• 1998

A three-waveguide coupler consisted of a central guide and two side guides is theoretically explored by using modal transmission-line theory. The numerical results reveal that the coupling length Lc is different from that calculated by coupled-mode theory and the difference increases gradually as the guiding modes increase.