• Proceedings of the Korea Concrete Institute Conference
• /
• 2009.05a
• /
• pp.453-454
• /
• 2009

In this dissertation, experimental program was carried out to study the hysteretic behavior of the reinforced different floor type interior beam-column joint repeated cyclic loads under seismic actions. The test results was as follow. The reinforced interior beam-column joint, designed by the different floor type, was increased energy dissipation capacity and maximum load carrying capacity according to the increase of different floor in comparison to standard specimen. And it was also dissimilar to failure mode adjacent to joint region. energy dissipation capacity of each specimen, designed by the different floor type, was increased 1.1${\sim}$1.35 times in comparison to standard specimen.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.25 no.6
• /
• pp.262-269
• /
• 2021

This paper conducts an evaluation of the structural performance of the lap splice detail of SD700 headed bar experiment for developing an RC beam with different depths joint details. The experiment variable is lap splice length, yield strength, and end anchorage of main reinforcements. For all specimens, a headed bar was applied to the main reinforcement of the beam with low depth (B2), and the beam with high depth (B1) was applied to the main reinforcement with two splice methods: straight headed bar and 90° hooked-headed bar. The experimental results were that specimens of applying SD500 and SD600 had the results of flexural fracture at the lap splice location, which maximum load was similar. For specimens of appling SD500, the 90° hooked-headed bar of B1, suppressed horizontal cracks in the lap splice section compared to the straight headed bar. Specimens of applying an SD 700 headed bar had the results of brittle anchorage failure. In addition, maximum load was increased with the lap splice length increasing. For specimens of applying SD700 headed bar, test for test maximum load/theoretical load for test development length/design development length were estimated to be 1.30~1.48 for the ACI 318-19 equation, and 1.14~1.30 for the KDS-2021 equation. Thus, ACI 318-19 equation had conservatively greater safety factors as estimated development lengththened.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2021.06a
• /
• pp.244-244
• /
• 2021

난류흐름 거동은 지형이나 수공구조물과 같은 고체 경계면의 변화에 민감하게 반응하며 특징 또한 다양하다. 보나 여수로 등과 같은 단차 구조물을 통과하는 흐름은 구조물의 모서리 같은 흐름 경계면이 급변하는 지점에서는 흐름분리(flow separation)가 발생하는 것이 특징이다. 이러한 흐름분리로 인해 전단층이 발생하며 흐름 재순환(recirculation)이 구조물 하류부에 형성된다. 이 연구에서는 낙차공 형식의 단차 구조물 하류부에서의 흐름 거동을 이해하기 위해 CFD모델링을 통하여 계산된 3차원 유동장을 분석한다. 난류 모의는 하이브리드 LES(large-eddy simulation)/RANS 계산 기법인 IDDES(improved delayed detached-eddy simulation)기법을 적용한다. IDDES의 기본 모형으로는 k-ω SST모형과 Spalart-Allmaras모형을 이용하여 두 모형의 성능을 평가한다. 자유수면의 변동은 VoF(volume of fluid)기법을 이용하여 계산하며, 각 지배방정식은 최소의 수치분산을 유지하면서 수치해의 안정성을 확보할 수 있는 2차 정확도의 유한체적법을 이용하여 이산화하였다. 수치해석 결과는 레이놀즈수 23,400과 후르드수 0.22의 조건에서 기존에 계측된 자료와 비교하여 수치모형의 정확도를 평가하고 하상 단차 하류부에서의 흐름 거동 특성을 분석한다. 계산 결과는 공학적으로 널리 사용되는 RANS 수치모의에서 볼 수 없는 전단층과 난류구조의 동적 거동 특성과 이에 따른 레이놀즈 응력분포의 특성을 설명해준다.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2007.05a
• /
• pp.1084-1088
• /
• 2007

국내에서 농업용수 취수, 수위 유지 등의 목적으로 18,000 개의 크고 작은 보가 하천에 설치되어 있으나 농경지의 도시화, 비닐하우스 단지화 등 토지이용의 변화와 대형 저수지의 축조/양수장 설치 등에 따른 취수 시설물의 통합 및 보체의 노후화 등으로 매년 50-150개의 보가 본래의 기능을 상실하여 용도 폐기되고 있다. 그러나 폐기된 보들이 철거 되지 않고 하천에 존치되어 하천생태통로의 단절, 수질 악화 등의 문제가 지속적으로 야기되고 있다. 외국의 경우에는 1970년대부터 본격적으로 기능을 상실한 보, 소형댐 등은 물론 일부 기능이 있는 하천횡단 시설물을 철거하여 하천환경복원을 추진하고 있다. 우리나라의 경우에는 최근 들어 기능을 상실한 보나 소형 댐 등에 한하여 하천생태통로 및 생태환경 복원 차원에서 철거의 필요성이 대두되기 시작하였다. 실제 철거도 이루어지고 있으나 체계적인 연구나 가이드라인 없이 지자체에 의해 이루어지고 있는 실정이다. 보는 하천을 횡단하는 구조물로 보의 상류에 저류지가 형성되고 많은 양의 퇴적물이 쌓여 그에 따른 하상의 단차가 형성된다. 이런 보가 철거됨으로 인해 막대한 양의 유사가 이동하게 되고, 철거 형태에 따라 하상 침 퇴적이 발생하고 그 위치나 양에 따라 하천 형태가 변할 수 있다. 이런 변화를 예측하여 철거에 따른 문제 등을 사전에 방지할 수 있는 기술이 필요하고, 철거에 대한 가이드라인 등이 마련되어야 할 것이다. 본 연구는 한강 제 1지류인 곡릉천에 위치한 곡릉2보의 철거에 따른 하상 변동, 하천 형태 변화 등 물리적 영향을 조사하고, 보 철거 후 장 단기적인 하도 및 하상 변동 등을 예측하는 기술을 개발하는 것이다. 연구 대상 보인 곡릉2보의 철거에 따른 모니터링 결과, 하상의 종단 변화는 그리 크게 생기지 않았으며 보 상 하류 횡단면에서 변화가 다소 큰 것으로 나타났다. 또한, 하상 재료의 부분적 변화도 발견되었으나, 전반적인 하천의 변화는 크지 않은 것으로 나타났다.

• Journal of the Korea Convergence Society
• /
• v.9 no.9
• /
• pp.263-270
• /
• 2018

The purpose of this study is to investigate the correlation between the demographic characteristics of Korean men and the preference of women's grading such as age, education, marital status, occupation, monthly income, and residence. After the questionnaire distribution, 333 questionnaires were analyzed statistically. Through this study, we will investigate the preference of men according to the step length of women's graduation cuts, and contribute to the establishment of the most preferred type of graduation cuts. As a result of the questionnaire analysis, 51.1% of all males preferred the gradation type with a large step of the cut length, and it was found that there was a difference in the preference for the step according to demographic characteristics (p <0.05) It is possible to conduct various studies on the style of the graduation cut among the hairstyles of women who are visually preferred and beautiful. In addition, it will be possible to derive the importance of customer satisfaction in hair salons, and it will be a basic index for searching for changes in the gradation cuts that can be applied in various ways while maximizing the aesthetic image of women.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.36 no.1
• /
• pp.18-26
• /
• 2016

The semiconductor industry is one of the key industries of Korea, which has continued growing at a steady annual growth rate. Important technology for the semiconductor industry is high integration of devices. This is to increase the memory capacity for unit area, of which key is photolithography. The photolithography refers to a technique for printing the shadow of light lit on the mask surface on to wafer, which is the most important process in a semiconductor manufacturing process. In this study, the width and step-height of wafers patterned through this process were measured to ensure uniformity. The widths and inter-plate heights of the specimens patterned using photolithography were measured using transmissive digital holography. A transmissive digital holographic interferometer was configured, and nine arbitrary points were set on the specimens as measured points. The measurement of each point was compared with the measurements performed using a commercial device called scanning electron microscope (SEM) and Alpha Step. Transmission digital holography requires a short measurement time, which is an advantage compared to other techniques. Furthermore, it uses magnification lenses, allowing the flexibility of changing between high and low magnifications. The test results confirmed that transmissive digital holography is a useful technique for measuring patterns printed using photolithography.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.20 no.4
• /
• pp.144-152
• /
• 2016

This paper focuses on the experimental study for investigating the performance for lap splice of hooked or headed reinforcement in beam with different depths. In the experiment, seven specimens, with its variables as the lap length of headed or hooked bar, the existence of stirrups, etc., was manufactured. Bending test was conducted. Lap strengths by test were compared with the theoretical model based on KCI2012. The result showed that the cracks at failure mode occurred along the axial direction to a headed bar. The initial stiffness and the stiffness after initial crack were similar for all specimens. For HS series specimens without stirrups, a 25% increase in lap length was increased 11.8~18.1% maximum strengths. For HH series specimens without stirrups, a increase in lap length did not affect the maximum strengths because of the pryout failure of headed bar. For HS series specimens, the theoretical lap strengths based on KCI2012 considering the B grade lap and the reduction factor for stirrup were evaluated. They are smaller than the test strengths and can ensure the safety in terms of strength capacity. For HH series specimens, the stirrups in the lap zone are needed to prevent the pryout behaviour of headed bar.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.4D
• /
• pp.593-600
• /
• 2006

Joint opening of jointed concrete pavement is caused by change in temperature and humidity of adjoined slab. The magnitude of joint opening influences on the load-transfer-efficiency and the behavior of sealant. If temperature or humidity decreases, joint opening increases. Generally maximum joint opening of a given joint is predicted by using AASHTO equation. While different magnitudes of joint opening at the individual joints have been observed in a given pavement section, AASHTO equation is limited to predict average joint opening in a given pavement section. Therefore the AASHTO equation may underestimate maximum joint for the half of joint in a given pavement section. Joints showing larger opening than the designed may experience early joint sealant failure, early faulting. Also unexpected spalling may be followed due to invasion of fine aggregate into the joints after sealant pop-off. In this study, the variation of the joint opening in a given pavement section was investigated based on the LTPP SMP data. Factors affecting on the variation are explored. Finally a probabilistic joint opening model is developed. This model can account for the reliability of the magnitude of joint opening so that the designer can select the ratio of underestimated joint opening.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2022.05a
• /
• pp.94-94
• /
• 2022

본류와 지류가 만나는 하천 합류부에서 발생하는 복잡한 흐름 구조는 하상변동에 영향을 주며, 본류와 다른 특성을 보이는 지류의 유입은 수질과 수생태계에도 영향을 준다. 합류부는 하천 변화의 다양성을 보이기 때문에 하천 관리 측면에서 중요한 구간으로, 흐름 및 혼합 특성 이해가 중요하다. 합류부에서의 흐름 및 혼합은 본류와 지류의 유량비, 밀도차, 단차, 합류각, 하도형상 등의 영향으로 그 양상이 달라지며, 흐름장 및 두 수체에 의한 이송물질의 혼합이 이루어졌다고 간주하는 혼합거리는 지류가 본류에 미치는 영향 범위 분석을 위한 중요한 매개변수이다. 본 연구에서는 합류부 흐름에 미치는 주요 인자 중 유량비와 밀도차가 합류부 흐름 및 혼합에 미치는 영향을 수치해석을 통해 분석하고, 조건의 변화에 따른 혼합거리를 예측해 보고자 한다. 본 연구의 대상 지역인 낙동강-황강 합류부는 다기능보와 댐의 운영에 따라 유입 유량 및 유량비가 조절되며, 여름철에는 황강의 수온이 낙동강보다 평균 4℃ 이상 낮으며, 9℃(지류 20℃; 본류 29℃) 이상의 수온차가 발생하기도 한다. 이 경우 밀도비는 0.998로 밀도류가 발생할 수 있는데, 밀도류가 발생할 경우 수표면과 저층이 분리되어 흐르기 때문에 동일 유량 조건에서도 혼합 양상은 달라진다. 밀도류가 발생하기 위해서는 수표면과 저층이 분리되는 성층이 발달해야 하는데, 이는 유속 또는 유량의 범위에 따라 성층의 발달 여부가 달라질 수 있다. 이러한 현장 조건을 반영한 수치해석을 통해 다양한 유량 조건(유량비)에서 밀도의 차이(수온차)가 합류부의 흐름 및 혼합에 미치는 영향을 분석해 보고자 하며, 합류부에서 밀도차에 의한 흐름의 변화 조건을 무차원수(Richardson number, Densimetric Froude number 등)를 통해 정량화해보고자 한다. 이는 지류가 본류에 미치는 영향의 정도와 범위를 파악함으로써 하천 관리를 위한 관측망 및 현장 조사의 범위 선정의 기초자료 마련뿐 아니라 본류의 수온 변화가 발생할 수 있는 범위의 파악을 통해 수생태계에 미치는 영향 파악을 위한 기초자료로 활용될 수 있을 것으로 기대된다.

• Journal of the Korean Institute of Traditional Landscape Architecture
• /
• v.28 no.1
• /
• pp.113-119
• /
• 2010

This study examined figurative characters of rice terraces, and is intended to seek figurative possibility of a natural scene by selecting Gyeongnam Area Namhae Gacheon rice terraces, Sancheong Imcheon rice terraces and Hamyang Macheon rice terraces through an analysis of the target land. As a theoretical background, studies of a natural scene and figuration-related literature were looked into, and for figuring a natural scene on the basis of the results, the character of the topography of rice terraces was divided into 9 items as follows by generalizing the inspiration obtained from the natural scenic character and spatial character of rice terraces represented from the topography: (1) Inclination showing the degree of the slope of rice terraces, (2) The bending showed by unevenness of the edge line of rice terraces, (3) The degree of parallelism of the up-and-down edge line, (4) The size of the width of the section of each rice terrace, (5) The area of the total rice terraces, (6) Step gap that indicates the difference of high and low of the up-and-down small rice terraces, (7) Figuration as an image represented by the external form of the total rice terraces, (8) Naturalness and artificiality kept by the total scene, (9) Softness of cornerstones or soil that forms small rice terraces, an atmosphere produced by the total scenes, etc. The results of analysis made through GIS, with rice terraces of Gyeongnam Namhae, Sancheong and Hamyang Area as the target land, are as follows. First, the steeper the inclination is, the higher the step difference of cornerstones becomes, and the steeper the inclination, the narrower the area and width become, so that it could be known that, in rice terraces, inclination is proportional to step difference and the area is inversely proportional to the width. Second, it is considered that line showed in rice terraces, area elements and reiteration, repeated changes, and changes in the scene affected by the surrounding environment including those according to season can be converted into a variety of images according to an individual disposition. Third, it was decided that it is possible to figure repetitive composition and directivity, motility, order and change, etc. into a common type drawn from each target land. This paper, as a study of basic materials for expressing figuration in an environment field, investigated and analyzed the surrounding environment of the target land, and is significant in that it attempted the possibility of being able to generalize the environmental beauty of the target land as one figurative element. More precise studies are expected to be made later.