• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.10a
• /
• pp.341-346
• /
• 2002

이 연구는 게르버 보 형식의 포스트텐션 PC 골조 구조 시스템의 실용화를 위해 골조 전체의 구조 성능 시험을 수행하며, 여기서 보-기둥 접합부 및 내민 보-단순 보 접합부의 구조 성능과 골조의 안전성을 확인한다. 시험은 400 mm$\times$800 mm 단면의 경간 3 m 보와 500 mm$\times$600 mm 단면을 갖는 높이 3 m 기둥의 실물 크기 시험체를 제작하여, 기둥에 80 톤의 축 하중을 준 상태에서 단순 보 중앙에 하중을 가력하여 기둥-보 접합부와 단순 보-내민 보 단면 축소 연결부의 구조성능을 파악한다. 시험 결과, 보 - 기둥 접합부는 예상 설계 하중 40톤 이상에서도 강 접합에 가깝게 거동하였고, 단순 보- 내민 보의 단면 축소 연결부는 경사철근의 사용으로 초기 균열 및 균열 확산에 대한 억제 효과가 있었으며, 예상 설계 전단력 40톤에서 안전하다는 것이 확인되었다.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.285-288
• /
• 2008

A model for the effective moment of inertia $I_{\epsilon}$ as expressed in Branson's equation, in which reduction of the flexural rigidity of RC beams due to cracking are aptly taken into accoun,t is presented. However, KCI Code isn`t considered tension stiffening as it is in debonding of reinforcing bar. Therefore, this equation need to set up suitable to our design Code. The experimental work consisted of casting and testing a total of 6 simply supported reinforced concrete beams and a total of 4 continuos reinforced concrete beams under two point concentrated loads. Main parameters are concrete strength, coverage, bond between concrete and reinforcing bars, are known as have an effect on deflection and tension stiffening. Every test beams had the same $250{\times}350$mm rectangular section, with a simply supported clear span of 4,400 mm and a continuos clear span of 6,500 mm. Comparison of the test results with values obtained using the KCI Code equation of the effective moment of inertia showed a noticeable difference.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.24 no.6
• /
• pp.138-145
• /
• 2020

This study was conducted to identify the structural performance of the opening in a location close to the support point in the perforated beam system of steel beams. In addition, structural performance was determined through experiments on reinforced openings using vertical and horizontal steel plates. In the steel simple beam, it was found that the opening was in a position closer to the support point, half the height of the steel beam (D/2), which was more appropriate than the height of the steel beam (D). In addition, the reinforcement effect of horizontal steel plate was greater than that of vertical steel plate reinforcement. Structural performance was improved when there was no gap between openings and steel plates.

• Fire Science and Engineering
• /
• v.29 no.4
• /
• pp.33-38
• /
• 2015

Loads applied on the floor are transferred through beams to columns. The beams can be designed as both end fixed or simple beams. The load bearing capacity of a beam depends on each boundary condition. However, when the load bearing capacity of a beam is evaluated in fire tests, all kinds of beams are tested using simple beam conditions. In this study, an analytical method performed using heat transfer theory and heat stress analysis based on the mechanical and thermal properties of SS-400 steel at high temperature. This method was used to clarify the differences between the two types of boundary conditions at normal and high temperature. The results show that the load bearing capacity of a both-end fixed beam at high temperature is superior to that of a simple beam. Therefore, the application of simple beam conditions in fire tests for evaluation of load bearing capacity is conservatively safe compared to fixed boundary conditions.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.25 no.6
• /
• pp.12-18
• /
• 2021

The purpose of this study is to effectively mitigate the bending displacement that occurs in the bridge due to forced vibration. We developed CTMD (Combine Tuned Mass Damper) that combines the relationship between spring and mass to control the bending behavior of simple beams. The experiment was conducted to confirm the control effect according to the change in the mass ratio of the developed CTMD. The developed CTMD is designed and manufactured so that the mass ratio can be adjusted according to the characteristics of the bridge. The maximum load of the spring applied to CTMD was fixed at 33.15 N. In order to evaluate the performance of the developed CTMD, a simple beam composed of hinges and rollers as boundary conditions was fabricated. In the experimental method, a CTMD was installed in the center of a simple beam and the deflection displacement according to the mass ratio was measured. The shaking condition was shaken at 3 Hz to induce the maximum bending behavior of the simple beam. As a result of the experiment, it was confirmed that when the optimal mass ratio was 2.1, the damping rate of the bending behavior displacement was about 71.2 %, indicating the best control effect.

• Journal of the KSME
• /
• v.35 no.8
• /
• pp.709-715
• /
• 1995

날로 그 중요성이 대두되고 있는 환경보존 문제에 능동적으로 대응하고 여러 계층 소비자의 안 전도, 쾌적성 등에 관련된 요구, 성능의 수준향상에 효과적으로 대처하기 위해서는 차량의 경량화 기술이 가장 먼저 선행되어야 할 과제이다. 경량화를 추구하는 방법은 최적설계 개념을 이용한 구조합리화에 의한 방법과 알루미늄, 강화 플라스틱 등 신소재 대체에 의한 방법이 병행 연구 되고 있다. 이 글에서는 구조합리화를 통한 경량화 목표를 달성하기 위해 설계 초기 단계에 활용 가능한 단순 보 모델 개발의 필요성에 관해 언급하고 실차의 도어 측면 붕괴강도(door side intrusion strength), 루프 붕괴강도 (roof crush strength) 해석을 위한 단순 보 모델 개발에 관해 소개하고자 한다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.2A
• /
• pp.259-267
• /
• 2008

The ultimate strengths of reinforced concrete deep beams are governed by the capacity of the shear resistance mechanism composed of concrete and shear reinforcing bars, and the structural behaviors of the beams are mainly controlled by the mechanical relationships according to the shear span-to-effective depth ratio, flexural reinforcement ratio, load and support conditions, and material properties. In this study, a simple indeterminate strut-tie model reflecting all characteristics of the ultimate strengths and complicated structural behaviors is presented for the design of simply supported reinforced concrete deep beams. In addition, a load distribution ratio, defined as a magnitude of load transferred by a vertical truss mechanism, is proposed to help structural designers perform the design of simply supported reinforced concrete deep beams by using the strut-tie model approaches of current design codes. In the determination of a load distribution ratio, a concept of balanced shear reinforcement ratio requiring a simultaneous failure of inclined concrete strut and vertical steel tie is introduced to ensure the ductile shear failure of reinforced concrete deep beams, and the prime design variables including the shear span-to-effective depth ratio, flexural reinforcement ratio, and compressive strength of concrete influencing the ultimate strength and behavior are reflected upon based on various and numerous numerical analysis results. In the companion paper, the validity of presented model and load distribution ratio was examined by employing them to the evaluation of the ultimate strengths of various simply supported reinforced concrete deep beams tested to failure.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2016.10a
• /
• pp.60-61
• /
• 2016

Performance has been developed in terms of structural strength. Especially, in a structural steels, it is regarded as a common design process that an yield stress of thicker plate than 40mm uses that of below 40mm in thickness. This can be done using TMCP(Thermo mechanical control process). In this study, the structural stabilities such as deflection, maximum load carrying capacity would be calculated in high temperatures.

• Magazine of the Korea Concrete Institute
• /
• v.10 no.4
• /
• pp.93-100
• /
• 1998

This paper presents a study on the flexural stiffness, plastic hinge length and plastic hinge rotation capacity of reinforced high performance concrete beams. 15 beams with different strength of concrete, reinforcement ratio and the pattern of loadings were tested. From the test results of reinforced normal strength concrete beams and reinforced high performance concrete beams with the concrete which has cylinder compressive strength of 700kg/${cm}^2$, slump value of 20~25cm and slump-flow value of 60~70cm. It is found that an extreme fiber concrete compressive strain of ${\varepsilon}_{cu}=0.0047$ may be used in ultimate curvature computations of reinforced high performance concrete beams. An empirical equation is proposed to estimate the effective moment of inertia. length and rotation capacity of plastic hinge of simply supported reinforced high performance concrete beams. The estimated deflections using this equation agree well with the experimental values.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.05a
• /
• pp.637-640
• /
• 2011

기존의 보안시스템은 설비가 비싸고 녹화를 끊임없이 계속함에 따라 저장 용량이 커야하는 문제점이 있고 영상을 단순히 저장하는 외에 다른 부가적 기능이 없다. 본 연구에서는 고성능, 고가의 장비가 아닌 단순한 PC 카메라 와 일반컴퓨터를 이용한 화상 보안 시스템을 제안 한다. 이 시스템은 단순한 녹화 외에 다양한 부가기능을 포함하고 있으며 프로그램이 설치된 컴퓨터를 떠난 외부에서도 감지한 침입을 통보 받을 수 있다. Main Application의 역할은 감시, 재생, 통계, 필터로 분류된다. 카메라에서 실시간으로 보내오는 영상을 메인 프로그램에서 보여주고 일시 정지, 필터 바로 가기 등을 통하여 필터와 연계된다. 이미 저장된 영상은 재생기능을 통하여 재생하며 이제까지 저장된 영상들은 모두 데이터베이스에 통계 화 되어 저장된다. 또한 실시간으로 보여 지는 영상들을 일정한 간격으로 웹 서버로 보내진다.