• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.595-596
• /
• 2008

가스 하이드레이트의 생성속도와 전환율을 높이며, 동시에 생성유도시간을 억제하기 위한 방법으로 다공질 물질을 활용하여 공극 내에 물을 함침시킨 후 가스와 반응시키는 제조방법을 개발하였다. 내용적 10 L 의 대용량 고압 반응기를 제작하여 실험을 수행하였으며, 장치 대형화에 따른 다공질 실리카겔의 다짐현상에 의한 발열제어 등에 대한 문제점은 특별히 나타나지는 않았다. 하이드레이트 형성을 위한 구동력이 높을수록 생성속도가 좋아지는 것을 확인하였다. 일반 벌크상 하이드레이트 제조법과 비교하여 매우 높은 생성속도 및 전환율, 거의 제거된 생성유도시간 등은 응용기술로 활용하기에 매우 바람직한 특성으로써 선택적인 가스분리, 가스저장 매체로 활용이 가능하다.

• Journal of the Korean GEO-environmental Society
• /
• v.13 no.1
• /
• pp.31-36
• /
• 2012

Recently, industrial by-products are exponentially growing because energy consumption is increasing due to rapid industrial development and improved living standards. The purpose of this study is to determine the proper mixing ratio to meet the liner conditions(must be less than $1{\times}10^{-7}$cm/sec), using pond ash and bentonite as liner. As the result of the compaction test, depending on the increase mixing ratio of bentonite, the maximum dry unit weight was decreased but the optimum moisture content was tended to be increased at the compaction curve. As the result of the permeability test, depending on the increase mixing ratio of bentonite, the coefficient of permeability showed tendency to be decreased in the form of index and the tendency was caused by the hydration reactions filling the void of the pond ash. When the mixing ratio of bentonite was approximately over 15%, it was satisfied with the land fill liner conditions. In other words, it is necessary to consider other mixtures containing the cement or another material in the economical aspect for application of the pond ash.

• Journal of the Korean Geotechnical Society
• /
• v.31 no.3
• /
• pp.27-38
• /
• 2015

Triaxial tests on sand-silt mixture specimens under low and high confining pressures were performed to understand their shear behaviors. The fines content in the mixture is lower than the threshold value. A series of tests under different conditions including fines contents (0%, 9.8%, 14.7%, 19.6%), density of specimen (controlled by different compaction energies of $E_c=22kJ/m^3$, $E_c=504kJ/m^3$), confining pressure (100 kPa, 1 MPa, 3 MPa, 5 MPa) were performed to investigate influences of these factors. Based on the test results, the threshold fines content, where the dominant structure of mixture changes from sand-matrix to fines-matrix, decreases with the increase of confining pressure. Under very high confining pressures, as a result of sand particle crushing, the behavior of the dense specimen is similar to that of the loose specimen which shows hardening, compression behavior, and shear strength increases with increase of fines content. In conclusion, silt is granular material like sand, and its influence on shear behavior of sand-silt mixture is very different from that of plastic fines on sand-fines mixture.

• Journal of the Korean Solar Energy Society
• /
• v.24 no.2
• /
• pp.63-71
• /
• 2004

Energy and environmental concerns accelerate the interest in passive solar heating in buildings, which utilizes solar energy through natural heat transfer. Moreover concerns about environmentally friendly materials were also increased. This study aims to evaluate the thermal performance of a Trombe wall built with earth. The thermal performance of the Trombe walls was analysed with results from computer simulations with TRNSYS 15. The thermal performance of the three types of Trombe wall was compared.: concrete. rammed earth. adobe. It was found that Trombe wall with the thermal storage wall of earth performed better than that of concrete. Rammed earth and adobe Trombe walls gained 4.7% and 12.8% more solar energy. respectively. than the concrete Trombe wall. In earth-applied Trombe walls. the energy gain by natural convection released from the airspace was about 75% of the total solar gains. that took 15% more than concrete Trombe wall. Rammed earth and adobe Trombe walls seem to be more suitable for buildings that use mostly in daytime. such as school, office and so on.

• 한국방재학회:학술대회논문집
• /
• 2008.02a
• /
• pp.313-316
• /
• 2008

Temperature reduction in the manufacturing of asphalt mixtures is highly desirable from a number of aspects. Reduced fumes and emissions, and reduced energy consumption, are important environmental reasons to continue pursuing the goal of temperature reduction. There are important construction and performance advantages as well. For instance, improved workability results in better compaction; lower production and placement temperatures may improve prospects for cold weather paving; and lower temperatures will result in less binder aging and possibly better cracking resistance. The performance of WMA is not to be satisfied though there are various advantages. Therefore, more research is needed on a number of issues

• International Journal of Highway Engineering
• /
• v.7 no.1 s.23
• /
• pp.49-61
• /
• 2005

The dynamic modulus of hot mix asphalt can be determined according to the different combinations of testing temperature and loading frequency. The superposition rule is adapted to get the master curve of dynamic modulus for each hot mix asphalt. There are couple of different methods to get the shift factor which is a key for making the master curve. In this paper, Arrehnius, 2002 AASHTO, and experimental method was employed to get the master curve. Evaluation of dynamic modulus for 25mm base course of hot mix asphalt with granite aggregate and two asphalt binders(AP-3 and AP-5) was carried out. Superpave Level 1 Mix Design with gyratory compactor was adopted to determine the optimum asphalt binder content(OAC) and the measured ranges of OAC were between 4.1% and 4.4%. UTM was used for laboratory test. The dynamic modulus and phase angle were determined by testing on UTM, with 5 different testing temperature(-10, 5, 20, 40, & $55^{\circ}C$) and 5 different loading frequencies(0.05, 0.1, 1, 10, 25 Hz). Using the measured dynamic modulus and phase angle, the input parameters of Sigmoidal function equation to represent the master curve were determined and these will be adopted in FEM analysis for asphalt pavements. The shift factor and activation energy for determination of master curve were calculated.

• International Journal of Highway Engineering
• /
• v.13 no.2
• /
• pp.103-114
• /
• 2011

Usage of bicycle has been supported the universal reduction of energy consumption and $CO_2$. For the same purpose, new constructions for long length bike roads are planned in Korea. Recently, laboratory tests of physical properties and resistance against environmental loading about optimum mix design of roller compacted concrete, that have advantages of high structural performance by cement hydration and aggregate interlocking, simple construction procedure and low construction cost, are performed for the effective construction of new bike roads. However, properties of roller compacted concrete had different results between laboratory and field tests since it had different compaction method. Also, construction method of roller compacted concrete are not defined for the application of bike roads since it had different demand performance such as thin pavement thickness, low strength and etc with road pavements. Thus, in this experimental research was launched to evaluate the core properties, visual inspection, compaction ratio, water content, thickness reduction rate of roller compaction, skid resistance and roughness by experimental construction about variable mix proportion and compaction method based on laboratory test results. And construction method of roller compacted concrete pavement were suggested for the application of bike roads.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.8 no.3
• /
• pp.51-58
• /
• 2008

Development of a new design guide which is based on empirical-mechanistic concept for pavement design is in action. It is called AASHTO 2002 Design Guide in USA and the KPRP(Korean Pavement Research Project) in Korea. The material characteristic of hot mix asphalt is a key role in the design guide. Therefore it is urgent to get a proper materials database, especially the dynamic modulus of hot mix asphalt. In this research, dynamic modulus test, which is based on aged asphalt binder, has been carried out and proposed the predicted equation of dynamic modulus. Nine different hot mix asphalt with three different asphalt binder have been used for the dynamic modulus test. Short-term aging, which is covers the time for the production of asphalt plant, transportation, lay-down, and compaction, can be simulated at $135^{\circ}C$ with 2 hour curing. Long-term aging has been carried out for a performance period of asphalt pavement. The dynamic modulus of asphalt pavement increases with aging time. As the nominal aggregate size increases, the change of dynamic modulus is not big.

• Journal of the Korean Geotechnical Society
• /
• v.24 no.1
• /
• pp.51-59
• /
• 2008

In this study, cyclic shear characterics of sand-clay mixtures were analyzed. In order to perform cyclic triaxial tests on sand clay mixtures, natural clays with activity and silica sand were mixed variously to reproduce soils with wide range of grain size compositions. Test specimens with various fines contents were prepared by the moisture compaction and pre-consolidation methods, while paying attention to the void ratio expressed in terms of the sand structure and clay structures, and undrained cyclic shear tests were performed. In the test results, cyclic shear strength decreased with increasing of sand granular void ratio below 20% of fine contents. When the granular void ratio of the test specimen exceeded the maximum void ratio of the silica sand, the clay matrix dominated the soil structure, and soil structures were not influenced by compaction energy. It was observed that, the matrix structure of the coarse particles has great effect on the undrained cyclic shear strength characteristics for sand-clay mixtures, and therefore, it is more appropriate to pay more attention to the density of the sand structure, rather than to the fines content.

• Journal of the Society of Disaster Information
• /
• v.14 no.3
• /
• pp.305-314
• /
• 2018

Purpose: Dynamic Replacement Method currently lacks of sufficient research, implementation cases, and case histories, compared with other comparable methods, such as Dynamic Compaction Method. Method: In this study, for Dynamic Replacement Method, the effective improvement depth and improved strength were analyzed for silty clayey soils. Results: Testbed test was performed to verify the effectiveness of Dynamic Replacement Method followed by the main dynamic replacement implementation on real construction site. Conclusion: A The effects of changes of soft ground depth, dynamic replacements' diameter, depth, spacing, and applied energy on dynamic replacement efficiency in silty clays were assessed and the followings were found: Empirical coefficient for soil $n_R$ of Dynamic Replacement Method was within the range of 0.14~0.32 and its ${\sqrt{WH}}$ is recommended to be 1.25~2.5 times of those from Dynamic Compaction Method.