• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.2
• /
• pp.195-200
• /
• 2007

We fabricated thermally-evaporated 10 nm-Ni/70 w-Poly-Si/200 $nm-SiO_2/Si$ and $10nm-Ni_{0.5}Co_{0.5}/70$ nm-Poly-Si/200 $nm-SiO_2/Si$ structures to investigate the microstructure of nickel monosilicide at the elevated temperatures required fur annealing. Silicides underwent rapid anneal at the temperatures of $600{\sim}1100^{\circ}C$ for 40 seconds. Silicides suitable for the salicide process formed on top of the polycrystalline silicon substrate mimicking the gates. A four-point tester was used to investigate the sheet resistances. A transmission electron microscope and an Auger depth profile scope were employed for the determination of cross sectional microstructure and thickness. 20nm thick nickel cobalt composite silicides on polycrystalline silicon showed low resistance up to $900^{\circ}C$, while the conventional nickle silicide showed low resistance below $900^{\circ}C$. Through TEM analysis, we confirmed that the 70nm-thick nickel cobalt composite silicide showed a unique silicon-silicide mixing at the high silicidation temperature of $1000^{\circ}C$. We identified $Ni_3Si_2,\;CoSi_2$ phase at $700^{\circ}C$ using an X-ray diffractometer. Auger depth profile analysis also supports the presence of this mixed microstructure. Our result implies that our newly proposed NiCo composite silicide from NiCo alloy films process may widen the thermal process window for the salicide process and be suitable for nano-thick silicides.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.32 no.1
• /
• pp.41-46
• /
• 2012

As the development of MEMS/NEMS structure and application technology the demand for an assessment of the mechanical properties have increased. The mechanical properties are mainly evaluated by using tensile test or ultrasonic wave measurement. However, the new technology have been developed such as nano-indentation, guided wave method because they have a limitation in case of a thin plate and thin film. In the study, the guided wave velocities are measured by electromagnetic-acoustic transducer(EMAT), the material properties of thin metallic foils are obtained using optimization process of the theoretical and experimental group velocity of guided wave. The Young's modulus obtained by the optimization process(201.6 GPa), nano-indentation(207.0 GPa) and literature value(203.7 GPa) of a $50{\mu}m$ thick nickel thin plate shows good agreement within 3%.

• Korean Journal of Optics and Photonics
• /
• v.18 no.6
• /
• pp.389-394
• /
• 2007

The characteristics of the single mode fiber hydrogen sensor have been investigated theoretically and experimentally. Palladium is adopted as a material for the transducer and a thin Ni film is used for the adhesion between the fiber end and the Pd film. It is shown that sensitivity and response time strongly depend on the thickness of Pd film. The single mode fiber sensor coated with 5 nm thick Ni adhesion layer and 10 nm thick Pd transducer layer showed 0.6 dB change of reflectivity and $3{\sim}5$ sec of response time as it absorbed 4% hydrogen gas.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.322-322
• /
• 2013

최근 전자제품들의 소형화, 경량화, 다기능화가 활발히 진행됨에 따라, 고성능의 고출력용 인쇄회로기판(PCB)의 개발이 요구되고 있다. PCB는 전자제품의 각 부품을 전기적으로 연결하는 통로로서 전자제품의 소형화, 다기능화에 따라 고집적화가 요구되고 있다. 하지만 모든 전자장비의 고장의 85% 정도가 발열에 의한 것으로, PCB의 고집적화에 따른 발열문제가 매우 중요한 이슈가 되고 있다. 최근에는 이러한 문제점을 해결하기 위해 PCB의 방열층으로 양극 산화막을 금속 기판 위에 형성하고 이 절연층 위에 금속층을 회로로서 형성하는 방열 PCB 기판에 대한 연구가 활발히 진행되고 있다. 최근까지, 금속층 회로 형성을 위해 무전해 Ni 도금에 대한 연구가 활발히 이루어져 왔다. 하지만 주로 화학적, 전기화학적 관점에서 많은 연구자들에 의해 조사 연구되어 왔다. 본 실험에서는 anodized Al 절연층 위의 회로전극 부분으로 스크린 방법으로 Ag paste를 패턴 인쇄한 뒤, 무전해도금 방식으로 저렴한 Ni 전면 회로전극을 형성하여 전기전도도를 높이고, 저항을 낮출 수 있는 회로로서 기판의 손상을 최소화하고 선택적으로 Ag 패턴에만 Ni 전극회로를 형성시키는 것을 목표로 연구하였다. Ni-B 무전해 도금시 도금조의 온도는 $65^{\circ}C$, 무전해 도금액의 pH는 ~7 (중성)로 유지하였다. Al2O3 기판을 이용한 Ag Paste 패턴 위에 증착된 Ni-B 박막의 특성을 분석하기 위해 X-ray diffraction (XRD), AFM (Atomic Force Microscopy), SEM (Scanning Electron Microscope), XPS (X-ray Photoelectron Spectroscopy)을 이용하여 Ni-B 박막의 특성을 분석하였다.

• Journal of Practical Engineering Education
• /
• v.6 no.2
• /
• pp.105-110
• /
• 2014

In this work, mechanical characteristics of titanium diaphragm have been studied as a potential robust substrate and a diaphragm material for automotive tire pressure sensor. Lamination process techniques combined with traditional micromachining processes have been adopted as suitable fabrication technologies. To illustrate these principles, capacitive pressure sensors based on titanium diaphragm have been designed, fabricated and characterized. The fabrication process for micromachined titanium devices keeps the membrane and substrate being at the environment of 20 MPa pressure and $200^{\circ}C$ for a half hour and then subsequently cooled to $24^{\circ}C$. Each sensor uses a stainless steel substrate, a laminated titanium film as a suspended movable plate and a fixed, surface micromachined back electrode of electroplated nickel. The finite element method is adopted to investigate residual stresses formed in the process. Besides, out-of-plane deflections are calculated under pressures on the diaphragm. The sensitivity of the fabricated device is $9.45ppm\;kPa^{-1}$ with a net capacitance change of 0.18 pF over a range 0-210 kPa.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.2
• /
• pp.81-86
• /
• 2003

To measure the pressure using semiconductor type pressure sensor in water or chemical solution, the sensor must be protected from the solution using proper packaging materials. stainless steel isolated type pressure sensor packaged with SUS316 can be widely used to measure the pressure in water or chemical due to its high corrosion-resistance and good performance in tensility and welding. Even if the surface of SUS316 has a plenty of nickel and chromium, the SUS316 is highly corrosive in acidic or alkaline solution. We coated parylene and adhesion promoting copper layer are 5${\mu}{\textrm}{m}$ and 200nm, respectively. The parylene coated stainless steel pressure sensor showed good anti-corosive characteristics in various strong acids. The accuracy of pressure sensor wasn't varied after parylene coating with 0.5%FSO.

• Korean Journal of Materials Research
• /
• v.15 no.5
• /
• pp.301-305
• /
• 2005

We fabricated nickel silicide layers on whole non-patterned wafers from $p-Si(100)SiO_2(200nm)$/poly-Si(70 nm)mn(40 nm) structure by 40 sec rapid thermal annealing of $500\~900^{\circ}C$. The sheet resistance, cross-sectional microstructure, surface roughness, and phase analysis were investigated by a four point probe, a field emission scanning electron microscope, a scanning probe microscope, and an X-ray diffractometer, respectively. Sheet resistance was as small as $7\Omega/sq$. even at the elevated temperature of $900^{\circ}C$. The silicide thickness and surface roughness increased as silicidation temperature increased. We confirmed the nickel silicides iron thin nickel/poly-silicon structures would be a mixture of NiSi and $NiSi_2$ even at the $NiSi_2$ stable temperature region.

• Korean Journal of Materials Research
• /
• v.28 no.10
• /
• pp.595-600
• /
• 2018

This study investigates the microstructural properties of CoCrFeMnNi high entropy alloy (HEA) oxynitride thin film. The HEA oxynitride thin film is grown by the magnetron sputtering method using nitrogen and oxygen gases. The grown CoCrFeMnNi HEA film shows a microstructure with nanocrystalline regions of 5~20 nm in the amorphous region, which is confirmed by high-resolution transmission electron microscopy (HR-TEM). From the TEM electron diffraction pattern analysis crystal structure is determined to be a face centered cubic (FCC) structure with a lattice constant of 0.491 nm, which is larger than that of CoCrFeMnNi HEA. The HEA oxynitride film shows a single phase in which constituting elements are distributed homogeneously as confirmed by element mapping using a Cs-corrected scanning TEM (STEM). Mechanical properties of the CoCrFeMnNi HEA oxynitride thin film are addressed by a nano indentation method, and a hardness of 8.13 GPa and a Young's modulus of 157.3 GPa are obtained. The observed high hardness value is thought to be the result of hardening due to the nanocrystalline microstructure.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.11a
• /
• pp.556-559
• /
• 2006

벌크형태의 태양전지 기판을 대체할 목적으로 연성기판을 적응한 태양전지 개발이 활발하게 진행되고 있으며, 주재료는 플라스틱 기판, 금속기판 등이 있다 그러나 기존의 연성기판인 플라스틱의 경우 열과, 내구성, 화학약품에 약하다는 단점이 있으며, 금속기판은 높은 생산원가, 박막화의 어려움 등의 문제를 안고 있다 이러한 문제를 극복하기 위해 전주성형법으로 제조된 철-니켈계 연성기판을 개발하였다. 이 연성기판의 경우 고온의 공정조건에서도 열팽창율이 플라스틱 기판보다 낮으며, 기존의 금속기판 보다 저렴한 생산단가로 쉽게 극박화 할 수 있다는 것이다. 전주성형법을 적용하여 40Ni, 45Ni, 52Ni 연성기관을 제조하였으며, TMA 장비를 사용하여 각 연성기판의 열팽창 계수를 측정한 결과 6.36, 6.78, $10.93{\mu}m/m^{\circ}C$로 기존의 연성기판인 플라스틱, 금속에 비해 낮은 열팽창 계수를 가짐으로서 고온 공정 중에 안정성 요구를 충분히 충족시킬 수 있다.

• Korean Journal of Materials Research
• /
• v.14 no.11
• /
• pp.769-774
• /
• 2004

15 nm-Co/15 nm-Ni/P-Si(100)[Type I] and 15 nm-Ni/15 nm-Co/P-Si(100)(Type II) bilayer structures were annealed using a rapid thermal annealer for 40sec at $700/sim1100^{\circ}C$. The annealed bilayer structures developed into composite NiCo silicides and resulting changes in sheet resistance, composition and microstructure were investigated using Auger electron spectroscopy and transmission electron microscopy. Prepared NiCoSix films were further treated in a sequential annealing set up from $900\sim1100^{\circ}C$ with 30 minutes. The sheet resistances of NiCoSix from Type I maintained less than $7\;{\Omega}/sq$. even at the temperature of $1100{\circ}C$, while those of Type II showed about $5\;{\Omega}/sq$. with the thinner and more uniform thickness. With the additive post annealing, the sheet resistance for all the composite silicides remained small up to $900^{\circ}C$. The proposed NiCoSix films were superior over the conventional single-phased silicides and may be easily incorporated into the sub-0.1 ${\mu}m$ process.