• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.10
• /
• pp.34-39
• /
• 2016

A low-voltage, low-power analog front-end IC for neural recording implant devices is presented. The proposed IC consists of a low-noise neural amplifier and a programmable active bandpass filter to process neural signals residing in the band of 1 Hz to 5 kHz. The neural amplifier is based on a source-degenerated folded-cascode operational transconductance amplifier (OTA) for good noise performance while the following bandpass filter utilizes a low-power current-mirror based OTA with programmable high-pass cutoff frequencies from 1 Hz to 300 Hz and low-pass cutoff frequencies from 300 Hz to 8 kHz. The total recording analog front-end provides 53.1 dB of voltage gain, $4.68{\mu}Vrms$ of integrated input referred noise within 1 Hz to 10 kHz, and noise efficiency factor of 3.67. The IC is designed using $18-{\mu}m$ CMOS process and consumes a total of $3.2{\mu}W$ at 1-V supply voltage. The layout area of the IC is $0.19 mm^2$.

• The Journal of the Korea Contents Association
• /
• v.22 no.9
• /
• pp.85-94
• /
• 2022

In modern society, environmental and energy problems have caused to replace cars with environment friendly energy. Vehicles with internal combustion engine which use petroleum are one of the factors that influence global pollution due to environment problems such as fine dust and ozone layer destruction. In addition use of energies for automobile making resources to become depleted. To solve this limited oil energy problem by using other energy sources. To the problem using electric energy and green energy as alternative for a solution. Among environment friendly energies this paper studies the possibility of drive service for autonomous vehicles that self-charges using only solar energy and whether they can be used as pollution free and alternative energy for automobiles. Studies was researched based on published literature review, data from ministry of transportation and automobile companies. Also case of electric vehicle and prototype automobile using only solar energy and the theory of near future technologies. Many automakers are using electric cars as alternative energy. Also making efforts to use solar energy as an substitute energy source and as a way to supplement electricity. Results show that there is a potential on operating autonomous vehicle using only solar energy. Furthermore, it will be possible to use automobiles actively, also use and supply solar energy. This paper suggest the possibility of contributing to the future of the automotive industry.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.23 no.2
• /
• pp.87-94
• /
• 2023

As the latest weapon systems and electronic equipments are increasingly demanding stealth technology to improve the survivability of allies, it is necessary to implement low-observability technology that reduces the radar cross section(RCS). In order to implement this stealth technology, a method for low RCS characteristics by applying a shape design or a electromagnetic wave absorber is widely used. However, active phased array antennas have structural limitations in shape design, also when a absorber is applied to it, the performance of the antenna is degraded. Therefore, in this paper, in order to realize the low RCS characteristics of the active phased array antenna operating in the X-band, individual radiating elements suitable for applying the radio wave absorber were selected, and a 13x13 array antenna was designed and manufactured. Next, by comparing the measured results of the relative RCS and electrical performance for the manufactured antenna according to the presence and type of the absorber, it is shown that the electrical performance is maintained at an equal or higher level while obtaining the low RCS characteristics. Thereby the method proposed in this paper for implementing the low RCS characteristics was validated. Finally, it was confirmed that when the wave absorber is applied to the array antenna, the limitation of its performance deterioration can be overcome.

• Korean Journal of Social Welfare Studies
• /
• v.42 no.4
• /
• pp.217-238
• /
• 2011

This study aims to investigate the effects of active coping of spouses on recidivism of domestic violence. In order to obtain better study results, 21-month follow up interview was conducted for spouses of batterers who completed domestic violence batterer intervention program. Spouses were interviewed for three times; 9-month, 15-month, and 21-month after program completion. Finally, data till 15-month follow-up was used to manage sample size problem. As a results, a total number of 76 spouses were included for final analysis. Data was collected from 2008 to 2009. Based on sample size and study objects, PLS(Partial Least Square) analysis was used. the prevalence rates of emotional abuse was 77.6% at the first interview but 41.3% at the second interview. For physical violence each rate were 43.1% and 18.4%. For emotional violence, problem-solving strategy among active coping shows significant moderating effects on reducing emotional violence(p<.001) while help-seeking among active coping has significant effects on decrease physical violence(p<.01).

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.5A
• /
• pp.849-859
• /
• 2006

This paper presents an extensive robust analysis of a ${\mu}$-controller in the hybrid system for various uncertainties using the benchmark cable-stayed bridge. The overall system robustness may be deteriorated by introducing active devices and the active controller may cause instability due to small margins. Therefore, a ${\mu}$-synthesis method that simultaneously guarantees the performance and stability of the closed-loop system (robust performance) with uncertainties is used for active devices to enhance the robustness in company with the inherent reliability of passive devices. The robustness of the ${\mu}$-synthesis method is investigated with respect to the additional mass on the deck, structural stiffness matrix perturbation, time delay of actuator, and combinations thereof. Numerical simulation results show that the proposed control system has the good robustness without loss of control performances with respect to various uncertainties under earthquakes considered in this study. Furthermore, the control system robustness is more affected by the perturbation of structural stiffness matrix than others considered in this study. Therefore, the hybrid system controlled by a ${\mu}$-synthesis method could be proposed as an improved control strategy for a seismically excited cable-stayed bridge containing many uncertainties.

• Proceedings of the Korean Society for Language and Information Conference
• /
• 2001.06a
• /
• pp.141-144
• /
• 2001

본 논문의 목적은 ‘다중 동사성 명사 구문’(Multiple Verbal Noun Construe-tions)의 논항실현 양상을 이론 중립적으로 고찰해 보고, 이 분석을 제약기반 문법 이론인 최근의 핵 심어주도 구구조문법 (Head-driven Phrase Structure Grammar)틀 안에서, 특히 다중계승위 계를 가정하는 제약기반 어휘부를 기반으로 형식화해 논항의 실현과정을 기술하고 설명하는 것이다. 우선 일본어의 유사한 현상을 분석한 Grimshaw & Mester (1988)의 격실현 양상에 관한 일반화를 기반으로 한국어 동사성명사구문의 논항실현 양상을 ‘논항전이’ (argument transfer)라는 이론적 장치를 이용해 형식화할 수 있음을 보이고, 동사성 합성명사의 논항구조를 만들기 위해 ‘논항합성’(argument composition)이라는 이론적 장치를 제안한다. 나아가서 다중 동사성 명사구문의 논항실현 과정에서 보이는 겹격표지 현상을 ‘격 복사’(case copying)를 제안해 동사성 명사의 격표지가 합성 명사에서 분리되어 문장단위에서 실현될 때 동일한 격을 복사해 실현한다는 점을 주장하고자 한다. 이 주장을 뒷받침하기 위해 수동과 능동 등 문법기능의 변화현상에서 하위범주화된 요소들의 격변화가 자의적이 아님을 실례를 들어 보여 주고자 한다. 일본어의 경동사 (light verbs)에 관한 분석 인 Grimshaw Meste, (1988) 이래 한국어에서도 이와 유사한 구문에 대한 재조명이 활발하게 이루어져 왔다 (Ryu (1993b), 채희락 (1996), Chae (1997) 등 참조). 한국어에서 ‘하다’와 동사성명사(verbal nouns)가 결합하여 이루어진 ‘동사성명사구문’ (Verbal Noun Constructions)에 대한 기존의 논의는 대부분 하나의 동사성 명사가 ‘하다’나 ‘되다등 소위 문법기능을 바꾸는 ‘경동사’들과 결합하여 복합술어가 되는 문법적 현상에 초점이 맞춰져 있었다. 그와 비교해서 동사성 명사의 어근이 두 개 이상 결합하여 동사성명사들끼리 합성명사(compound nouns)를 이루고 그 동사성 합성명사가 문법기능의 변화를 바꾸는 ‘경동사’와 결합하여 이루어진 복합술어에 대해서는 논의가 거의 없는 형편이다. 특히 이 지적은 핵심어주도 구절구조문법틀 내에서는 논란의 여지가 없다. 본 논문의 대상은 바로 이러한 합성 동사성명사의 논항구조와 동사성명사에 의해 하위범주화된 논항들의 문법적 실현양상이다.

• The Journal of the Petrological Society of Korea
• /
• v.23 no.4
• /
• pp.311-324
• /
• 2014

The Hongjeom formation of the Pyeongan Supergroup in the Munkyeong coalfield mainly consists of metapsammite and metapelites. Metampelites occur as slate preserving chloritoid+chlorite+muscovite and andalusite+biotite+chlorite+muscovite mineral assemblages. Chloritoid and andalusite occur as porphyroblast, and the matrix composed of fine-grained micas. Metamorphic P-T conditions for these mineral assemblages are $510-520^{\circ}C$ and 3.0-3.5kbar based on P-T pseudosection in $MnO-K_2O-FeO-MgO-Al_2O_3-SiO_2-H_2O(MnKFMASH)$ system and isopleth intersections of Fe/(Fe+Mg) ratios in chloritoid and chlorite. The medium temperature and low pressure metamorphism resulted from a higher geothermal gradient ($40-45^{\circ}C/km$) condition than that of burial metamorphism. The youngest (SHRIMP U-Pb age; ca. 327-310 Ma) detrital zircon grains from the Hongjeom formation display oscillatory zoning and relatively high Th/U ratio (0.60-1.12). Based on the previous sedimentary, paleontological, and geochronological studies in the Taebaeksan basin together with results of this study, we suggest that (1) initial deposition of the Hongjeom formation was contemporaneous with a magmatic activity in the provenance, (2) the Pyeongan Supergroup was deposited in an arc-related basin at an active continental margin during the Carboniferous to Permain, and (3) magmatic activities occurred repetitively in relatively short interval in the active continental margin had continuously supplied sediments to the basin.

• (The)Study of the Eastern Classic
• /
• no.69
• /
• pp.481-507
• /
• 2017

The petition movement to Paris peace conference was the movement for 137 Neo-Confucian scholars including Kwak Jong-seok to ask for Korean independence in March, 1919. Kim Bok-han had led all the course of Ho-seo version. Although we don't know the exact contents on the both of Yeong-nam and Ho-seo versions, but Ho-seo version might be more conservative than Yeong-nam version in comparison with other versions. This was because Ho-seo version basically represented the conservative stance of the Neo-Confucian scholars in Ho-seo (Southern Chung-cheong province). However although Ho-seo version had conservative characteristic, the projecting and practicing of petition movement to Paris peace conference shows Kim Bok-han's active attitude. What I would like to explain in this paper is the background of how spontaneously Kim led the movement. Especially I tried to make Kim's historical status be revealed through talking the idealogical history of Neo-Confucianism ignored until now. Although Kim received blames he behaved with barbarians when he led the petition movement from the conservatives, Kim never submitted on those blames. Kim's tolerant attitude was prominent in relation with Hwa-seo school against which Nam-dang school(Kim's party) was a rival, especially from also after 'the problem of Choe Ik-hyeon' in 1903. This attitude was connected to the petition movement in tolerant manner. The tolerant attitude like this was revealed from Kim's historical consciousness attached importance to 'the completion of work'.

• Journal of Hospice and Palliative Care
• /
• v.6 no.2
• /
• pp.133-143
• /
• 2003

Purpose : Amont the various issues concerning bio-ethics, the concern on euthanasia has increased along with the development of medical technology. Thus, the general public tends to have more liberal opinion. They have detail research data and real practices in US, Europe and Australia, but we lack such studies in our country. This study was undertaken to address the need of studies on the recognition of euthanasia among the public because the existing studies have been focused on the medical staff. Methods : Survey 413 people the age of 17 or more, from May to July 2000. Testify the data on the variation of demography and the recognition of euthanasia by using SAS 6.12, the statistic program. Results : 304 people (73.6%) think that euthanasia should be legislated, 156 people (37.8%) permit euthanasia to the rage of voluntary one, and 234 people (56.6%) permit passive euthanasia. When the subject of voluntary euthanasia was himself, more people whose age is 35 or more (P=0.001) responded that they will undertake euthanasia. And, on issues related to the passive euthanasia, one's educational background (P=0.046) and economic power (P=0.040) arrangement showed significant differences. When the subject of voluntary euthanasia is other people, more people whose age is 35 or more than 35 (P=0.001), whose sex is male (P=0.001), and married people (P=0.002) were for allowing the matter. For the subject of passive euthanasia, survey participant's occupation (P=0.016) created meaningful difference. More people whose age is 35 or more than 35 responded that they want voluntary euthanasia for themselves (P=0.001), and in the case when euthanasia is legislated, marital status (P=0.002) also shows meaningful difference. Passive euthanasia is permitted by the more people whose age is less than 35 for respondents other people (P=0.001), marital status show meaningful difference in case for respondent himself. In the case of legal euthanasia is more people whose age is 35 or more than 35 (P=0.001), sex is male (P=0.004) and more married people (P=0.001) responded that they want voluntary euthanasia for other people. And, age (P=0.002), sex (P=0.001), education (P=0.025) and economic power (P=0.001) show meaningful difference for case the subject of passive euthanasia. Conclusion : Most of general public responded that the legislation on euthanasia is required; and, age, education and economic power seem to have an influence on their decisions on euthanasia. Not only such a study of demographic and sociological correlation; but, various basic data on the legislation of euthanasia are needed.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.16 no.3
• /
• pp.60-66
• /
• 2012

This paper aims to constitute a feedback vibration control system using wireless sensor networks and experiment it on a model structure to verify its effectiveness. For the purpose, we set up a feedback vibration control system composed of a wireless input/output(I/O) sensor node based on bluetooth, a home-made shear type MR damper, a shaker which generates a constant size of sine wave, and a simple beam model structure. The vibration control experiment was performed by shaking the 1/4 point of beam with a shaker. At the moment of shaking, we controled the vibration with MR damper which was placed vertically on the center of beam. Simultaneously, by acquiring acceleration response at the 2/4 point of beam, we evaluated the effectiveness of control capability. The control command was set to send a voltage signal to MR damper when the acceleration response, acquired from the wireless I/O sensor node placed at the center of beam, was more than a certain amount. Although the realtime feedback vibration control system constituted in this paper is effective only within a limited command system, it has been proven that the system was able to effectively decrease the vibration of structure by generating a control command aimed for realtime purpose. The system also showed a possibility to be used as a structural response control system adapting a variety of semi-active control algorithm.