• Tribology and Lubricants
• /
• v.14 no.1
• /
• pp.94-98
• /
• 1998

혈관내피세포는 혈관의 내벽에 단일 층을 구성하고 있는 상피세포로 동맥경화나 혈관협착의 원인에 매우 중요한 역할을 하는 것으로 알려져 있다. 그리고, 모든 혈관 질환의 발생장소가 혈관이 나뉘는 분지부에 집중되고 있어, 혈류역학과 혈관질환 간에 상호연관성이 있음을 짐작할 수 있다. 특히, 최근에 와서 혈관내피세포가 혈액유동에 의해 발생하는 전단응력을 인지하여 혈관의 제반 생리적 반응을 조절한다는 연구결과가 속속 발표되고 있어, 혈관질환의 극복을 위한 연구 개발에 혈관내피세포에 대한 이해의 중요성이 증대되고 있다. 이에 본 연구에서는 혈관내피세포에 혈류와 같은 크기의 전단응력을 부가하여 세포의 생리적 반응을 고찰할 수 있는 평판형 층류발생장치를 설계, 제작하였다. 설계된 평판형 층류발생장치는 유동환경 하에서의 혈관내피세포의 동적반응을 고찰 할 수 있도록 유동액의 온도, 산도, 전단응력의 크기를 조절할 수 있도록 설계하였으며, 제작된 실험장치를 이용하여 전단응력에 의한 혈관내피세포의 형태변화를 고찰하였다. 개발된 층류발생장치는 혈관내피세포의 연구 뿐 아니라, 백혈구의 점착, 암세포의 전이등에도 다양하게 활용이 가능하다.

• Polymer(Korea)
• /
• v.30 no.6
• /
• pp.471-477
• /
• 2006

Ion exchange metal composite(IPMC) has toughness equivalent to the range of human's muscle, transformation-actuation force by relatively low voltage and the fast response time. Thus, as a new method for preparing thicker IPMC, the solution casting method to make the films of various thicknesses out of liquid nation was attempted in this study. To reduce the surface resistance of electrode, the first plated electrode prepared by Oguro method was replated with Au and Ir using ion beam assisted deposition(IBAD). The microstructures of electrode surfaces before and after IBAD plating were investigated using SEM. The change of water and ion-conductivity in IPMC were measured under applied voltage. The displacement and driving force of IPMCs with various thicknesses were measured to evaluate the driving properties.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2000.04a
• /
• pp.36-36
• /
• 2000

액체로켓엔진에 사용되는 2000psi이상의 고압 연소실(Combustion Chamber)의 냉각은 내피(Inner Shell)에 기계 가공된 냉각통로(Cooling Channel)로 냉각제를 흘려보내는 재생냉각방식이 널리 사용되며 기계 가공된 냉각 통로는 외피(Outer Shell)에 의해서 지지 밀봉된다. 일반적으로 내피 재료는 순수한 구리보다 강도가 우수하고 열전도도는 유사한 구리합금을 사용하고, 외피는 강도가 우수한 스테인레스 강을 사용하여 브레이징 접합된 구조를 형성한다. 브레이징 공정은 조립품을 약 $450^{\cire}C$ 이상의 액상선을 갖는 삽입금속(Filler Metal)을 사용하여 적당한 온도($450^{\cire}C$ ~ 모재의 고상선)에서 가열하여 접합시키는 방법으로, 용융 금속의 젖음 현상(Wetting Phenomena), 접합 틈새(Joint Clearance)로의 용융 삽입금속의 유입(Capillary Phenomena)과 접합 계면의 반응을 통해서 접합이 이루어진다. 이는 일반적인 접합 공정과 비교하여 모재의 변형이 적고, 이종 금속 간의 접합이 용이하며, 복잡한 부품을 정밀하게 접합할 수 있는 장점이 있으나, 접합될 제품의 표면 상태 및 분위기(Atmosphere), 접합될 부품간의 조립 틈새, 가열 싸이클(Heating Cycle) 등에 대한 공정 확립 및 관리가 매우 중요하다. 재생냉각 구조를 갖는 연소실은 우선 접합면의 형상이 매우 복잡하여 균일한 접합 틈새를 유지하면서 접합시키기가 매우 어려우며, 고온, 고압의 환경에서 작동하므로 일부 접합면이 접합되지 않을 경우 내피의 변형 및 파괴가 발생하고, 브레이징 시 용융된 삽입금속이 냉각통로 내로 유입될 경우 연소 시 이부근에서 재료의 용융이 발생될 수 있다. 따라서, 이러한 현상을 방지하기 위해서는 진공 분위기 하에서 적절한 접합 틈새를 유지할 수 있는 공정 및 장비의 개발이 필요하다.

• Korean Journal of Food Science and Technology
• /
• v.35 no.1
• /
• pp.84-91
• /
• 2003

The effects of different dehydration conditions for the removal of ginkgo nut inner coat on peeled ginkgo nuts were examined using physical and sensory methods. Dehydration of ginkgo nuts at $90^{\circ}C$ for 120 min resulted in greater hardness, lightness (L), redness (a), yellowness (b), and firmness. Higher roasted flavor and larger holes were observed with dehydration at $150^{\circ}C$ for 30 min and greater cooked ginkgo flavor and green color with dehydration at $120^{\circ}C$ for 50 min. Based on these findings, dehydration at $120^{\circ}C$ for 50 min was determined as the adequate hot air dehydration condition for the removal of ginkgo nut inner coat. Ginkgo nuts stored at $25^{\circ}C$ maintained overall desirability up to 4 weeks. In ginkgo nuts stored at $4^{\circ}C$, all sensory desirabilities evaluated were reasonably high until 60 days of storage; desirability of appearance decreased moderately at 80 days of storage, and appearance became very undesirable at 180 days. Ginkgo nuts stored at $-18^{\circ}C$ showed little changes until 10 months of storage, but slight decreases in overall desirability, flavor, and texture were noted at 12 months.

• Analytical Science and Technology
• /
• v.20 no.3
• /
• pp.213-218
• /
• 2007

Copper(II) ion was measured with the use of a perfluorinated sulfonated polymer-ethylenediamine (nafion-en) modified glassy carbon electrode. The electrode mechanism was based on the chemical reactivity of an immobilized layer (nafion-en) to yield complex $[Cu(en)_2]^{+2}$. The reduction potential peak by differential pulse voltammetry(DPV) was observed at -0.4402V(${\pm}0.0050V$) (vs. Ag/AgCl). The linear calibration curve was obtained from $1.0{\times}10^{-6}$ to $1.0{\times}10^{-4}M$ copper(II) ion concentration, and the detection limit(3s) was $1.96{\times}10^{-6}M$.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.10a
• /
• pp.449-452
• /
• 2009

This paper was designed to fabricate the miniature spur gear with pitch circle of 1.8 by hot extrusion process of mechanically alloyed Zn-22wt%Al powder at various temperature. The mechanical alloying was preformed for ball milled times of 8h, 16h and 32h by the planetary ball milling. Mechanically alloyed powders were compacted cylindrical performs. Extrusions of the miniature spur gear using the alloyed powder were carried out at different extrusion temperatures. The extruded spur gear was sintered for 2h at $350^{\circ}C$ in argon atmosphere. The friction between the die and the powdered billet and the internally different density due to complex product shape cause the internal crack. To overcome the mentioned problems, high dimensional accuracy at cross section of the spur gear and uniform Vickers hardness could be obtained by graphite lubricant and controlling holding time.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.11a
• /
• pp.723-726
• /
• 2005

The two major obstacles in the application of IPMC to flapping actuators operated in the air are solvent loss and actuation force. In this paper, solvent loss of various IPMCs made of Nafion$^{TM}$117(183$\mu$m thickness) has been experimentally investigated to find out the best combination of cation and solvent for minimal solvent loss in IPMCs and higher actuation force. For this purpose. experiments for the internal solvent loss measurement of IMPCs have been conducted for various combinations of cation and solvent. From the experiments, it was found that heavy water showed improvement in the operating time up to more than two minutes. in the tip force measurement of IPMCs, it was found that smaller and thicker IPMCs produced larger tip forces. However, the shorter IPMCs generated reduced actuation displacements and created flapping motion with decreased natural frequency. For the design of flapping device actuated by 5mm wide, 10mm long, 0.2mm thick IPMCs were used in the stacked form. Since the actuation force is a few gram-force, we stacked five IPMCs to improve actuation force. To amply the actuation force, rack-and-pin ion type hinge was used for the flapping device and insect (Cicadidae) wing was attached to the stacked IPMC actuator. In the flapping test, the device could generate flapping angle of 15$^{\circ}$ at 6Hz excitation by 2.5 voltage square wave input.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.105-105
• /
• 2018

스테인리스강은 내식성과 내구성이 우수하여 파이프 및 일반 구조용 고온재료에 널리 사용된다. 그러나 선박 및 해양플랜트 등의 고부가가치 산업에 사용될 경우 내피로성, 내구성 및 내식성이 더욱 요구되고 있다. 특히 해수 환경 하에서 스테인리스강은 재료 표면의 부동태 피막 파괴로 공식 또는 틈부식에 의한 국부부식을 초래하여 해양환경용 재료로 사용하는데 제한적이다. 플라즈마 이온질화는 저온에서 열처리가 가능하며 재료의 변형이 없어 스테인리스강에 널리 적용되는 열화학적 표면처리 기술이다. 플라즈마 이온질화는 일반적으로 고온에서 실시하여 스테인리스강의 기계적 특성을 향상시키는 목적으로 주로 적용하였으나, 저온-플라즈마 이온질화 처리 시 질소의 확산계수 증가로 표면에 S-phase 생성에 기인하여 부식 저항성이 향상된다고 알려져 있다[1-2]. 그러나 해수 펌프, 밸브, 스트레이너(Strainer) 등의 해양 환경용 기자재로 널리 사용되고 있는 주조 스테인리스강에 대한 플라즈마 이온질화 적용과 그 연구는 미비하다. 따라서 본 연구에서는 주조용 스테인리스강에 대하여 플라즈마 이온질화 기술을 적용하여 공정온도에 따른 해수 내 전기화학적 부식 특성을 규명하였다. 플라즈마 이온질화 공정은 $25%N_2$와 $75%H_2$ 비율로 $350^{\circ}C{\sim}500^{\circ}C$의 공정온도에서 10시간 동안 실시하였다. X-선 회절분석을 통해 공정온도 변수에 따른 표면에 형성된 질화층의 상변화를 분석하였다. 또한 비커스 경도계를 이용하여 표면경도를 측정하여 기계적 특성 향상을 확인하였다. 전기화학적 부식 실험 후 표면 손상 형상 관찰, 무게 감소량 및 손상 깊이 계측을 통해 공정 온도와 부식 저항 특성을 규명하였다. 또한 타펠 분석을 통해 모재와 플라즈마 이온질화 온도 변수에 따른 부식 속도를 비교 분석하였다.

• Food Science and Preservation
• /
• v.5 no.4
• /
• pp.326-330
• /
• 1998

Freeze storage technique is widely used for food processing to keep freshness and quality of the product. This technique was applied to fresh, unshelled groundnut to develop a new type of product which could maintain fresh taste and nutritive values even after several months of storage. The groundnut varieties, Daepungtangkong, Daekwangtangkong and Sindaekwangtangkong were grown at the experimental field of NCES in 1996. Immatured pods or groundnut were harvested around 20 to 3o days before full maturity, washed, and steamed at 100$^{\circ}C$ for 5 min. to stop enzyme activity. After vacuum packing (at -760mmHg for 10 min.) with 0.08mm polyvinyldichloride film, the pods were immediately frozen at -70$^{\circ}C$ for 24h and transfered at -20$^{\circ}C$ for long-term storage. Physico-chemical properties of frozen vegetable groundnut were investigated at 2 months after storage and compared to those of conventionally dried groundnut. After 2 months storage, the thawed kernels were very palatable with softness and fresh taste. Acid value and hardness (measured as the compression force on the probe of a texture analyzer) were much lower in frozen vegetable groundnut than those in the air-dried ones. Presence of free sugars is one of the important factors affecting groundnut taste, and the free sugar contents were considerably decreased in the frozen vegetable groundnut compared to freshly harvested groundnut. But in dried groundnut no free sugar was detected.

• Journal of Chest Surgery
• /
• v.41 no.6
• /
• pp.679-686
• /
• 2008

Background: Cellular remnants in the bioprosthetic heart valve are known to be related to a host's immunologic response and they can form the nidus for calcification. The extracellular matrix of the decellularized valve tissue can also be used as a biological scaffold for cell attachment, endothelialization and tissue reconstitution. Thus, decellularization is the most important part in making a bioprosthetic valve and biological caffold. Many protocols and agents have been suggested for decellularization, yet there ave been few reports about the effect of a treatment with hypotonic solution prior to chemical or enzymatic treatment. This study investigated the effect of a treatment with hypotonic solution and the appropriate environments such as temperature, the treatment duration and the concentration of sodium dodecylsulfate (SDS) for achieving proper decellularization. Material and Method: Porcine aortic valves were decellularized with odium dodecylsulfate at various concentrations (0.25%, 0.5%), time durations (6, 12, 24 hours) and temperatures ($4^{\circ}C$, $20^{\circ}C$)(Group B). Same the number of porcine aortic valves (group A) was treated with hypotonic solution prior to SDS treatment at the same conditions. The duration of exposure to the hypotonic solution was 4, 7 and 14 hours and he temperature was $4^{\circ}C$ and $20^{\circ}C$, respectively. The degree of decellularization was analyzed by performing hematoxylin and eosin staining. Result: There were no differences in the degree of decellularization between the two concentrations (0.25% 0.5%) of SDS. Twenty four hours treatment with SDS revealed the best decellularization effect for both roups A and B at the temperature of $4^{\circ}C$, but there was no differences between the roups at $20^{\circ}C$. Treatment with hypotonic solution (group A) showed a better ecellularization effect at all the matched conditions. Fourteen hours treatment at $4^{\circ}C$ ith ypotonic solution prior to 80S treatment revealed the best decellularization effect. The treatment with hypotonic solution at $20^{\circ}C$ revealed a good decellularization effect, but his showed significant extracellular matrix destruction. Conclusion: The exposure of porcine heart valves to hypotonic solution prior to SDS treatment is highly effective for achieving decellularization. Osmotic treatment with hypotonic solution should be considered or achieving decellularization of porcine aortic valves. Further study should be carried out to see whether the treatment with hypotonic solution could reduce the exposure duration and concentration of chemical detergents, and also to evaluate how the structure of the extracellular matrix of the porcine valve is affected by the exposure to hypotonic solution.