• Korean journal of applied entomology
• /
• v.43 no.3 s.136
• /
• pp.225-231
• /
• 2004

An endoparasitoid wasp, Cotesia plutellae, has been used for a biological control agent against the diamondback moth, Plutellae xylostella. It has a symbiotic polydnavirus in their reproductive tract, which is required for its successful parasitization. Here, we measured a specific replication time of the polydnavirus during female development of C. plutellae. We, also, analyzed the reproductive potentials of female C. plutellae under mating or different host conditions. At $25^{\circ}C$, pupal C. plutellae began to develop adult tissues such as compound eyes and wings since day 2. At day 5, all adult tissues including antennae were developed and were ready to emerge. With polyclonal antibody raised against C. plutellae polydnavirus, an immunobloting could confirm virus replication at day 4 during pupal stage. Virus particles could be visualized by transmission electron microscope in the oviduct lumen of day 5 pupae. After adult eclosion, venom gland and ovarian calyx increased in size, though ovarioles did not. Mated females layed large number of eggs (over $60\%$) at first 4 days during their mean longevity of ca. 8 days at $25^{\circ}C$. Unmated females showed less active ovipositional behavior, where all the eggs developed into males. C. Plutellae parasitized both P. xylostella and fall webworm, Hyphantria cunea. However, C. Plutellae developed faster and showed higher successful paarasitization in P. xylostella than in H. cunea.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.7
• /
• pp.689-695
• /
• 2012

The friction factor in a rod bundle and the loss coefficient at a spacer grid were examined. As a test section, 25 smooth rods, 9.5 mm in diameter and 2000 mm in length, were prepared and installed in a $5{\times}5$ square array in a square channel. In this case, the P/D (Pitch-to-Diameter ratio) was 1.35. In this work, plain (i.e., no mixing vanes), split-vane, and hybrid-vane spacer grids were tested. In a bare rod bundle (i.e., no spacer grid), the measured friction factors were in good agreement with the previous correlations. Among the spacer grids tested, the hybrid-vane spacer grid presented the largest friction factor in the rod bundle and loss coefficient. This may be because of the flow pattern change induced by large relative plugging of the flow cross section and mixing vane geometry. At Re=$5{\times}10^5$, the predicted loss coefficients of plain, splitvane, and hybrid-vane spacer grids were approximately 0.79, 0.80, and 0.88, respectively.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.14 no.2
• /
• pp.114-120
• /
• 2011

The characteristics of a helical turbine to be used for tidal stream energy conversion have been numerically studied with varying a few design parameters. The helical turbines were proposed aiming at mitgating the well known poor cut-in characteristics and the structural vibration caused by the fluctuating torque, and the basic concept is introducing some twisting angle of the vertical blade along the rotation axis of the turbine. Among many potential controling parameters, we focused, in this paper, on the twisting angle and the height to diameter ratio of the turbine, and, based on the numerical experiment, We tried to propose a configuration of such turbine for which better performance can be expected. The three-dimensional unsteady RANS equations were solved by using the commercial CFD software, FLUENT with k-${\omega}$ SST turbulence model, and the grid was generated by GAMBIT. It is shown that there are a range of the twisting angle producing better efficiency with less vibration and the minimum height to diameter ratio above which the efficiency does not improve considerably.

• Korean Journal of Plant Resources
• /
• v.30 no.1
• /
• pp.50-57
• /
• 2017

This study aimed to investigate the morphological characteristics and optimal germination conditions in seeds of Arabis pendula L., a traditionally edible and medicinal plant. The external seed shape was circular-obovate with narrow wings and dark brown. The seed length and width were 1.25 mm and 1.47 mm, respectively. The seeds were exalbuminous and the embryo was a bent type. Seed germination was the highest (49.7%) at $20^{\circ}C$ under dark conditions among the various temperature and light conditions applied. However, under the dark condition, the seedling was weak, overgrown, and the cotyledons were small and folded. To improve the germination and growth of seedlings, the seeds were pre-treated with $GA_3$ solutions of varying concentrations (0, 200, 500, and 1,000 mg/L). The seed germination and seedling growth were effectively improved by $GA_3$ pre-treatment. The germination rate was the highest (97.3%), mean germination time was the shortest (8.1 days), and a vigorous growth of seedlings was observed upon pre-soaking the seeds in 500 mg/L $GA_3$ solution. In conclusion, the best method for germination was pre-soaking in 500 mg/L $GA_3$ ($4^{\circ}C$, dark, 24 h) and incubating the seeds at $20^{\circ}C$ for 15 days.

• Korean journal of applied entomology
• /
• v.33 no.3
• /
• pp.148-152
• /
• 1994

This study was carried out to investigate insect specles of Kiwi fruit, and ecological characteristicsof Stathmopoda m Chonnam province from 1991 to 1993 Twelve families and thirteen specieswere identified during the study. Sfothmopoda aurijerello and mulberp scale were key insect pestsamong them. The body sizes of each stage of S. a~irijereilo was measured and found to be 0.12 mmfor egg, 9.8 mm for mature lawa. 5.9 mm for pupae and 123mm for adult with opened wings.S, ouriferelia appers to have two generations a yea Adults occut~ed from late May to midJulyand mid-August to early September Mth two peaks m early to midJune and late August. Changein age structure (% lawe: % pupae) over time was 100: 0 in earlyJul, 96. 1 . 3 9 in midduly. 64.9:35 1 in late July. 19.8 . 80 2 in early August, and 0 : 100 in mld-August Damaged fruit was 4 6%in early July, increase above 40% 1" midJuly, and then the damage surpassed the damage threshold.The rate of fruit damaged was 45.9%, and there wbi no significant dtfferences among countiesDamaged parts of fruits were manly fruit apex Mth 70% and followed by fruit stalk w~th 11.1%.The rate of fruit damaged by varieties were Hayward with 25.7%. Monty with 17 5%. Hyangrokwith 13.9%, Abott with 9.3% and Bruno with 6.0%. with 9.3% and Bruno with 6.0%.

• Journal of Bio-Environment Control
• /
• v.25 no.4
• /
• pp.277-282
• /
• 2016

This study was aimed to investigate the effect of air-circulation fans on air temperature and relative humidity in a single-span tomato greenhouse (W: 7m, L: 25m, H: 3.2m). According to standard of fan layout by ASAE (1997), a total of 10 fans were bilaterally arranged in 2 rows in the experimental greenhouse. The distributions of air temperature and relative humidity were measured from 6 pm to 8 am under different conditions, with and without fans. The measurement heights were 0.7m, 1.7m and 2.7m. Under the condition of "fans off", the spatial differences of air temperature and relative humidity between upper and lower sides were $1.7^{\circ}C$ and 10.8%, respectively. The operation of 10 fans showed their differences to $0.1^{\circ}C$ and 3.2%. The number of fans and installation direction were evaluated their performance on reducing the spatial variation of air temperature and relative humidity. The experimental layouts were 5 and fans in 2 rows (bilaterally) and 10 fans in the one (same) direction. Under the condition of "6 fans on" and "5 fans on", the spatial differences of air temperature and relative humidity between upper and lower side were $0.3^{\circ}C$, 3.4% and $0.3^{\circ}C$ and 4.0%. The operation of 10 fans in the one direction reduced their differences to $0.5^{\circ}C$ and 4.9%. The overall findings of this study showed that there was no significant differences under each condition. Therefore, this study suggested that it is more economic and effective to install five fans in 2 rows (bilaterally) in the greenhouse (W: 7m, L: 25m, H: 3.2m).

• Journal of Korean Society of Forest Science
• /
• v.2 no.1
• /
• pp.59-65
• /
• 1962

The objects of this experiment are to find out the local variation of the Dendrolimus Spectabilis Butler, of which sample was first collecteted 15 bodies of male and 35 bodies of female adult at Suwon area. the wing veins and the scale shape have been observed through the microscope (100) and the scale size (from the bottom of the scale to the top of the lobe) has also been measured by the micrometer. The results of this experiment are as follows: 1. There is nodifference between the venation of the male body and that of the female body. Also we can not find any differences between the right and the left wing, and between each body. The fore wings consit of 13 longitudinal veins and the only one "V" shape cross vein which is between the 5th and 6th vein. The hind wings consist of 9 longitudinal veins and the only one "V" shape cross vein which is mentioned above. 2. The scale types are divided into 4 Groups in its shape. (A) The scales of I Group are short and the lower parts of them almost look like a circle, having a small projection at their bottom. The upper parts of them have 2 or 10 lobes. We can find the lobes with fine hairs or the lobes without them at the top of the scales. (B) The scales of II Group are longer than that of I Group. The shape of the lower parts of the scales is similar to that of I Group. The upper parts of the scales have 2 or 10 lobes. (C) The scales of III Group are long and almost alike in a long wedgeshape. The upper parts of the scales have 2 Or IO lobes and we can find long fine hairs at the top of each lobe. (D) The scales of IV Group are long and the shape of the lower parts of the scales is similar to that of III Group. The lobes are short and not sharp. We can find 2 or 9 lobes. 3. The scales of I Group and II Group are distributed on the whole surface except on the outer margin. The most scales of III Group are distributed on the wing base. The scales of IV Group are distributed on the outer margin only. The scales with 4 or 5 lobes are most widely distributed not considering their Group or distributing parts. 4. In I Group the variation of the scale length become gradually greater as the number of the lobes are increasing. In II, III, IV Group, however, the variation of the scale length is in direct opposition to the above mentioned. The variation of the scale width becomes pretty small in any Groups and the scale width become wider as the number of the lobes are increasing. 5. The source of the wing colouration is pigmnetal colour, and the wing colouration is expressed by the amount of brown and white scales.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.46 no.8
• /
• pp.611-620
• /
• 2018

For the past decades, the analytic model for distributed surface roughness has been developed to improve the accuracy of the icing simulation code. However, it remains limitations to validate the developed model and determine the empirical parameters due to the absence of the quantitative experimental data which were focused on the surface state. To this end, the experimental study conducted to analyze the ice covered surface state from a micro-perspective. Above all, the tendency of the smooth zone width which occurs near the stagnation point has been quantitatively analyzed. It is observed that the smooth zone width is increased as growing the ambient temperature and freestream velocity. Next, the characteristics of the ice covered surface under rime and glaze ice have been analyzed. For rime ice conditions, ice elements are developed as the opaque circular corn in the opposite direction of freestream. The height and interval of each circular corn are increased as rising the ambient temperature. For glaze ice conditions, numerous lumps of translucent ice can be observed. This is because the beads formed by gravity concentrate and froze on the lower surface.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.38 no.3
• /
• pp.209-216
• /
• 2002

How to estimate the shape of trawl net and ropes of a midwater trawl on full scale was described by implementing a three-dimensional semi-analytic treatment of a towing cable system with the field experiments obtained with the Scanmar system. The shape of trawl net from wingend to the beginning of codend was assumed to be of form $\chi$$^2$/ae$^2$+ y$^2$/be$^2$=(z - c)$^2$/c$^2$, and that of the ropes attached behind otter boards be of form yr = $A\chi$rB. In case of warp length 300m long, the volume of trawl net, the ratio of net height to net width at the mouth of the trawl net, and the inclination angle of float rope were estimated according to the change of towing speed. The volume and the distance between wingtips were increased with increasing towing speed. And the inclination angle of float (or ground) rope was slightly decreased with increasing towing speed.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.34 no.3
• /
• pp.238-244
• /
• 2001

A method of estimating the fluid drag of a fishing gear and otter board spread in a midwater trawl on full scale was described by implementing a three-dimensional semi-analytic treatment of the towing cable (warp) of a trawl system with the field experiments obtained with the SCANMAR system. The shape of hand rope, bridle and float(or ground) rope attached behind otter boards in a horizontal plane was assumed to be of form $y_r=Ax_r^B$. The distance between otter boards (otter board spread) obtained by the three dimensional analysis of a towing cable must be equal to that obtained by the functional equation of the shape of ropes behind otter boards, The angle of attack of ropes which can be obtained from the functional equation enables one to estimate the fluid drag of trawl net (net drag) by subtracting the fluid drag of the hand rope and bridles from the drag component of the tension of hand rope attached just behind the otter boards.