• Journal of the Korean GEO-environmental Society
• /
• v.9 no.2
• /
• pp.61-65
• /
• 2008

In this study, a newly modified soil nailing technology named as the PGSN (Pressurized Grouting Soil Nailing) system is proposed. Effects of various factors related to the design of the pressurized grouting soil nailing system, such as the length of re-bars and type of reinforcement materials, were examined throughout a series of the displacement-controlled field pull-out tests. 9 displacement-controlled field pull-out tests were performed and the ratio of injected grout volume to grout hole volume were also evaluated based on the measurements. In addition, short-term characteristics of pull-out deformations of the newly proposed PGSN system were analyzed and compared with those of the ordinary soil nailing system by carrying out field pull-out tests. The test results were shown that the displacements of pressurized grouting soil nailing system were decreased 30~36% in comparison with using gravity grouting soil nailing system by the pressurized effect. The displacements of steel tube were diminished 31~32% comparison with using deformed bar by the reinforcement type change from the field pull-out tests.

• Journal of the Korea Concrete Institute
• /
• v.25 no.4
• /
• pp.371-379
• /
• 2013

This paper investigates the cracking and tension-stiffening behavior of 100 MPa shrinkage-compensated strain-hardening cement composite (SHCC) and conventional concrete tie elements in monotonic and cyclic tension. Strain and surface crack formation of tension ties were monitored with two strain displacement transducers and a photo microscope with a lens of magnification 50 times. Three different cement composites such as conventional concrete, shrinkage-compensated SHCC, and normal SHCC were used in the tie specimens to investigate the influence of the cement composite type on the tension stiffening and cracking behavior. Test results indicated that initial shrinkage of the ultra high-strength cement composites is greatly reduced as the 10% replacement of cement by the shrinkage-compensating admixture based on calcium sulfo-aluminate (CSA). The test results on the SHCC tension ties showed that the first cracking load decreases proportionally to the initial shrinkage strain. Reinforced ultra high-strength SHCC ties with the initial shrinkage compensation exhibited improved tension stiffening and smaller crack spacings, i.e. the reduction in crack width. Cyclic loading did not have a significant effect on tension stiffening and cracking behavior of tension ties with normal concrete and SHCC materials.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.23 no.2
• /
• pp.231-242
• /
• 2013

Recently, automated software testing methods such as fuzzing have been researched to find software vulnerabilities. The purpose of fuzzing is to disclose software vulnerabilities by providing a software with malformed data. In order to increase the probability of vulnerability discovery by fuzzing, we must solve the test suite reduction problem because the probability depends on the test case quality. In this paper, we propose a new method to solve the test suite reduction problem which is suitable for the long test case such as file. First, we suggested the length of test case as a measure in addition to old measures such as coverage and redundancy. Next we designed a test suite reduction algorithm using the new measure. In the experimental results, the proposed algorithm showed better performance in the size and length reduction ratio of the test suite than previous studies. Finally, results from an empirical study suggested the viability of our proposed measure and algorithm for file fuzzing.

• Journal of the Korea Concrete Institute
• /
• v.18 no.2 s.92
• /
• pp.177-188
• /
• 2006

Conventional nonlinear finite element analysis requires complicated modeling and analytical technique. Furthermore, it is difficult to interpret the analytical results presented as the stress-strain relationship. In the present study, a design-oriented analytical method using the truss model was developed. A reinforced concrete member to be analyzed was idealized by longitudinal, transverse, and diagonal line elements. Basically, each element was modeled as a composite element of concrete and re-bars. Simplified cyclic models for the concrete and re-bar elements were developed. RC beams and walls with various reinforcement details were analyzed by the proposed method. The inelastic strength, energy dissipation capacity, deformability, and failure mode predicted by the proposed method were compared with those of existing experiments. The results showed that the proposed model accurately predicted the strength and energy dissipation capacities, and to predict deformability of the members, the compression-softening model used for the concrete strut element must be improved.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.7
• /
• pp.723-730
• /
• 2012

During the cold wire-drawing process, the diameter of a wire is reduced and the length of the wire is increased as the wire passes through the die. The pressure and sliding motion at the interface between the wire and die cause elastic recovery of the workpiece and friction and wear on the die. In addition, wire deformation and frictional heating raise the temperature of the wire and die, resulting in difficulty in manufacturing the drawn products according to a designated inner diameter of the die, deviating from the designated dimension or the inner diameter of the die. In this study, considering the die temperature distribution, the effects of dimensional changes of the drawn products were analyzed quantitatively; these changes are caused by the elastic deformation of the die, the elastic recovery of the workpiece, and the thermal deformation of both the die and the workpiece. It was confirmed that the elastic recovery of the workpiece influenced these changes the most. The initial dies considering these factors could avoid deviation from the designated dimension, and the desired drawn products were obtained by using the designed initial drawing dies.

• Journal of the Korea Concrete Institute
• /
• v.20 no.4
• /
• pp.459-467
• /
• 2008

This paper describes a proposal for average crack width and immediate deflection calculation in structural concrete members. The model is mathematically derived from actual bond stressslip relationships and tension stiffening effect between reinforcement and the surrounding concrete, and the actual strains of steel and concrete are integrated respectively along the embedded length between the adjacent cracks so as to obtain the difference in the axial elongation. With these, a model for average crack width and immediate deflection in reinforced concrete flexural members are proposed utilizing difference in the axial elongation and average steel strain and moment-curvature relationship with taking account of bond characteristics. The model is applied to the test specimens available in literatures, and the crack width and deflections predicted by the proposal equation in this study are closed to the experimentally measured data compared the current code provisions.

• Journal of the Korean Geotechnical Society
• /
• v.34 no.11
• /
• pp.107-119
• /
• 2018

PHC piles, extension-plate attached PHC piles, and steel pipe attached PHC piles were installed in field test site. Axial compressive static load tests including load distribution test and Pile Driving Analyzer (after driving) were done on the tip-transformed PHC piles and the grouted tip-transformed PHC piles. Load-displacement curves of three different type of PHC piles, which are PHC pile (TP-1), extension plate attached PHC pile (TP-2) and steel pipe attached PHC pile (TP-3), showed almost the same behavior. Thus bearing capacity increase effect of the tip-transformed PHC piles was negligible. Share ratio of side resistance and end bearing resistance for PHC pile, extension plate attached PHC pile, and steel pipe attached PHC pile were 95.8% vs. 4.2%, 95.6% vs. 4.4%, and 97.8% vs. 2.2% respectively.

• Journal of Bio-Environment Control
• /
• v.28 no.3
• /
• pp.204-211
• /
• 2019

The purpose of this study is to provide basic data for setting environmental design standards for domestic greenhouses. We conducted experiments on thermal environment measurement at two commercial greenhouses where hot water heating system is adopted. We analyzed heat transfer characteristics of hot water heating pipes and heat emission per unit length of heating pipes was presented. The average air temperature in two greenhouses was controlled to $16.3^{\circ}C$ and $14.6^{\circ}C$ during the experiment, respectively. The average water temperature in heating pipes was $52.3^{\circ}C$ and $45.0^{\circ}C$, respectively. Experimental results showed that natural convection heat transfer coefficient of heating pipe surface was in the range of $5.71{\sim}7.49W/m^2^{\circ}C$. When the flow rate in heating pipe was 0.5m/s or more, temperature difference between hot water and pipe surface was not large. Based on this, overall heat transfer coefficient of heating pipe was derived as form of laminar natural convection heat transfer coefficient in the horizontal cylinder. By modifying the equation of overall heat transfer coefficient, a formula for calculating the heat emission per unit length of hot water heating pipe was developed, which uses pipe size and temperature difference between hot water and indoor air as input variables. The results of this study were compared with domestic and foreign data, and it was found to be closest to JGHA data. The data of NAAS, BALLS and ASHRAE were judged to be too large. Therefore, in order to set up environmental design standards for domestic greenhouses, it is necessary to fully examine those data through further experiments.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.2
• /
• pp.766-773
• /
• 2021

Chemicals, such as ammunition, are disposable items that cannot be reused because of their operational characteristics. The reliability of the test process and test results are important factors in evaluating the performance of guns and ammunition. The pressure after firing is a crucial value in an acceptance test of guns and ammunition performance; hence, accurate measurements are required. The pressure in the artillery is measured using the copper crusher gauge. The compression amount of copper is converted into a pressure by either a length-pressure conversion table or conversion formula. Therefore, the exact measurement of the squeeze of the copper crusher is related directly to the correct estimate of the pressure. Currently, the pressure is measured manually by the operator, which always includes some human error. In this study, the cause of the measurement error was analyzed, and the automatic measuring system for copper crusher deformation was developed to minimize the error elements. A copper crusher could be measured using the probe sensor and CCD camera, and the Jig for stable positioning was also designed. A designated SW was also developed for the system operating and measurement-analysis. This measuring system through this study may be used for an ammunition stockpile reliability test and gun/ammunition acceptance test.

• Journal of Biosystems Engineering
• /
• v.9 no.1
• /
• pp.34-45
• /
• 1984

우리가 소비하는 식량의 확보는 단위 수량의 증대 뿐만 아니라, 생산이후 수확, 조제가공 및 건조 저장과정에서의 곡물 손실 방지 또는 감소로 인한 간접 증산으로도 이룩될 수 있는데, 현재 우리나라에서는 수확 이후의 곡물 손실량이 전체 생산량의 약 11%에 달하는 것으로 추정되고 있다(12). 여기서 식량의 중요 손실원으로 기계적 원인과 곡물 자체의 특성에 의한 두가지 요인을 고려할 수 있다. 따라서 쌀의 물리적 특성이 규명되면 각 과정에서 발생되는 기계적 손실을 더욱 줄일 수 있을 것이다. 이러한 중요성에도 불구하고 지금까지 우리나라에서는 벼의 물리적 특성에 관한 연구가 거의 없는 실정이다. 특히 우리나라에 많이 보급되고 있는 통일계 품종은 관행 품종에 비하여 물리적 특성이 크게 다르다고 인정되고 있다. 따라서 본 연구는 벼와 현미의 특성을 기계적 및 유동학적 측면에서 함수율 및 품종별로 규명하여, 농업기계의 설계 및 작동조건, 그리고, 조제가공의 기초적 자료로 제시하고자 하였다. 실험 결과를 요약하면 다음과 같다. 1. 준 정하중의 압축시험에서 함수율은 벼와 현미의 기계적 및 유동학적 특성에 큰 영향을 미쳤으며, 특히 높은 함수율에서는 점성적인 특성이, 낮은 함수율에서는 탄성적인 특성이 나타났다. 2. 벼와 현미의 함수율이 24-12% (습량기준)의 범위에 있을 때 현미의 항복점은 2.0-7.2kg, 벼의 항복점은 2.5-7.6kg을 나타냈으며, 전반적으로 현미보다 벼의 항복점이 0.5-1kg 더 높았다. 또한 함수율이 18%(습량기준) 이하에서는 일반계 품종이 통일계 품종보다 압축 강도가 더 높았으나 18% 이상의 높은 함수율에서는 더 낮게 나타났다. 그리고 낮은 함수율에서 현미의 항복점은 현미 두께 대 길이의 비의 증가에 따라 직선적으로 감소하였다. 3. 현미의 최대압축 강도는 함수율 24-12%(습량기준)의 범위에서 2.94-10.4kg을 나타냈으며, 14% 수준의 낮은 함수율에서는 현미의 최대 압축 강도는 5.66-11.4kg으로 품종간에 높은 유의성이 있었다. 따라서 벼와 현미의 크기가 최대 압축 강도에 큰 영향을 미친 것으로 사료된다. 4. 함수율 12-24%(습량기준)의 범위에서, 현미의 항복점에서 변형은 0.20-0.40mm를 나타냈으며, 함수율이 약 17%일 때 최소치를 보였다. 벼의 항복점에서 변형은 0.20-0.41mm 였으며 통일계 품종이 일반계 품종보다 변형이 더 많이 생겼다. 5. 함수율 24-12%(습량기준)의 범위에서, 일반계 품종의 레질리언스(resilience)는 $0.142-0.603kg{\cdot}mm$, 통일계 품종의 레질리언스는 $0.229-0.601kg{\cdot}mm$로 나타났다. 함수율이 19% 이하에서는 일반계 품종이 통일계 품종보다 더 높게 나타났으며 19% 이상에서는 반대 현상이 일어났다. 또한 14%의 낮은 함수율에서, 현미의 레질리언스는 현미 두께 대 길이의 비의 증가에 따라 감소하였다. 벼의 레질리언스는 함수율의 감소에 따라 증가했으며, 그 범위는 $0.285-0.850kg{\cdot}mm$이었다. 6. 현미의 터프니스(toughness)는 함수율 24-12%(습량기준)의 범위에서 $0.841-2.795kg{\cdot}mm$이었다. 또한 일반계 품종과 통일계 품종 사이에는 유의성이 없었으나. 품종간에는 높은 유의성이 있었다. 7. 현미의 탄성계수와 스티프니스(stiffness)는 함수율의 감소에 따라 직선적으로 증가하였다. 현미의 함수율이 24-12%(습량기준)의 범위에 있을 때 탄성계수는 $7-40kg/mm^2$, 스티프니스는 8-34kg/mm를 나타냈다.