• Journal of Drive and Control
• /
• v.10 no.4
• /
• pp.7-13
• /
• 2013

A tractor is a farm vehicle that is designed to provide a high tractive effort at low speed. It is used for versatile agricultural tasks such as hauling a trailer, tillage, mowing and construction work. As the intensity of work increases, tractors equipped with automatic transmission become popular due to the work convenience. Though manual and power shuttle transmissions are produced by domestic corporations, development for full-automatic power shift transmissions has never been challenged, and so related technology level is quite low. This paper gives a survey of the automatic transmissions from advanced foreign company, which includes layout of gear train, the way hydraulics controls clutches and brakes, electronic control system. The results are expected to be utilized as a basis in the development of original power train design for tractor.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.9
• /
• pp.77-83
• /
• 1996

This paper describes forging of trochoidal gears, which are being widely used in timing belt pulley, pump pulley etc., as a series of development of the simulator for non-axisymmetric elements. Kinematically admissible velocity fields for forging of trochoidal gear were proposed and the loads were calculated by numerical method. When the simulation was carried out, half pith of gear was divided into 6 deformation regions which have different velicity fields by assumptions and boundary conditions. The neutral surface was introduced into forging of trochoidal gears with flat punch and, for each step, it is assumed as a circle with its radius r$_{n}$. The experimental set-up was installed in 200 ton hydraulic press for forging. The billets, of A1 2218 aluminum alloy, were slightly phosphate-coated. It was shown that thd theoretical solutions, as upper bound, are useful to predict the forging load for forging of trochoidal gears, because thdt give estimates that are substantially higher than experimental loads.s.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.9
• /
• pp.61-67
• /
• 1997

Hardened layer and compressive residual stress created by carburized treatment effect on bending strength of gear massively. Also, shot peening treatment improves the strength of carburized gear as it does the hardness and residual stress of surface layer. In these days shot peening techniques are welcomed as one of physical improvement ways around the surface of materials. It is used widely because qualitative analysis of shot peening has become possible and surface treatment can be done with very little costs comparaed to other surface improvement methods. Therefore this study investigates the effect of shot peening in surface shape and bending fatigue strength after doing many kinds of shot peening treatments, then doing fatigue test and also explained characteristics of shot peening gear.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2001.10a
• /
• pp.257-262
• /
• 2001

As computer-related technologies have been developed, legacy design systems have not been appropriate for new computing environment. Therefore, it is necessary that most of them are either modified or newly developed. However, this requires quite much amount of cost and time. This paper presents a method of extending legacy design system without modification using XML and XSLT. In order to apply the developed method, a good example of legacy design systems, AGMA gear rating system has been extended so as to be suitable for the distributed computing environment. An XML document for AGMA gear rating process is defined. It is transformed to the form of the input document of AGMA gear rating system by XSLT processor according to the transformation rules defined in the AGMA gear rating XSLT document. After that, AGMA gear rating system reads this input document and generates an output document in the server. These operations are automatically executed by the external legacy system controller without user interactions. Using these operations, AGMA gear rating web service has been developed based on SOAP and WSDL to provide the functions of legacy AGMA gear rating system through the distributed network. Any system or user can implement AGMA gear rating process independently to the platform type, without making it for oneself, by simply referring the AGMA gear rating web service via Internet.

• Journal of the Korean Institute of Gas
• /
• v.18 no.6
• /
• pp.45-50
• /
• 2014

In this paper, designed the driving part of a straight line precision transfer system which can be applied to industrial machines and industrial robots. The direction of power transfer and the output characteristic are similar to those of the conventional rack-pinion type, but it applied new pin-pinion type to the driving part. As a result, it achieved indefinite expandability in length and secured the convenience of installation. To determine the optimal contact of pin-pinion gear, it conducted a Cycloid tooth profile analysis.

• Tribology and Lubricants
• /
• v.36 no.2
• /
• pp.96-104
• /
• 2020

The electric vehicle industry is rapidly developing because of enforced environmental regulations, and several studies have been conducted on the multispeed transmission to improve the fuel efficiency of electric vehicles. Among these studies, research on the power density improvement of electric vehicle transmission is critical. Thus, the optimal design of the gear train is necessary to enhance transmission efficiency. In this study, an optimal design methodology for the lightweight two-speed transmission of electric vehicles is proposed. Because a multispeed transmission has many operating conditions and equality and inequality constraints, a new gear design method that combines analytical and iterative methods is applied without using complex optimization algorithms. Sets of possible design variables are generated considering the operating conditions and various design variables. The modules and face width ratios of each stage gear that satisfy the corresponding operating conditions are analytically calculated. The volume of the gear train is calculated, evaluated, and arranged using these values to determine the optimal solution for minimizing the volume, and the proposed methodology is applied to the actual model to verify its effectiveness. The design of a two-speed transmission with multiple operating conditions and constraints without complicated optimization algorithms can be optimized.

• Journal of Korea Society of Industrial Information Systems
• /
• v.5 no.1
• /
• pp.31-36
• /
• 2000

This paper presents a design method of deadbeat controller for DC motor driving a rotational system with gear. The deadbeat-response design developed for control system of a sampled continuous-data process does not guarantee zero intersampling ripples, but the proposed deadbeat control system that consists of the integral controller and the full-order state observer, and zero-order hold using in continuous systems, has many advantages such as an output response without the ripples and reaching the steady state without error after a given sampling period and faster settling time than the optimal control system in the same sampling period. The results of a case study through matlab simulation are shown that the efficiency of the proposed controller for DC motor driving a rotational system with gear is verified by comparing with optimal controller etc.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1995.06a
• /
• pp.54-64
• /
• 1995

대표적인 대형 베어링인 일체형 볼 베어링과 와기어 레이스형 볼 또는 로울러 베어링의 마찰 특성을 비성형 유한요소 프로그램인 MARC를 사용하여 상호간의 마찰형상에 대한 접촉응력과 마찰력 특성을 비교 해석하였다. 특히 와이어 레이스식 슬루잉 링 베어링은 우수한 마찰특성 때문에 건설기계, 하역기계, 광산기계나 탱크와 같은 국방무기 등에서 널리 사용되고 있다. 접촉면의 변형에 따른 일체형의 볼 베어링은 마찰력과 기울기면에서 와이어 레이스식 베어링에 비하여 크고, 같은 와이어 레이스식 베어링에서는 마찰력의 경우 볼 타입이 로울러 탕입에 비하여 약간 크게 나타났다. 이들의 계산결과를 종합하면 와이어 레이스식 베어링이 일체형 베어링에 비하여 마찰특성이 우수하고, 특히 와이어 레이스 베어링중에서 로울러 타입은 마찰 토오크면에서 균일하기 때문에 베어링을 사용한 제어기능 설계에서 특히 우수한 결과를 제공할 수 있다. 유한요소 해석결과는 기존의 실험결과와 잘 일치하고 있어서 슬루잉 링 베어링의 최적설계에 유한요소 해석의 유용함을 확인하였다. 또한 상부 구조물과 하부 구조물을 연결하기 위한 체결볼트의 구멍은 하중조건에 따라서 구조적 불안정성을 야기할 수 있음도 확인하였다.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.2
• /
• pp.437-444
• /
• 2010

The audio data have been communicated using analog methods or simple protocols. However, with the advent and improvement of various multimedia functions, many audio devices have been integrated into a mobile handset in which interconnection lines are very complicated. Conventional point-to-point connections such as $I^2S$ and PCM demand more power consumption whenever more devices are attached. In this paper, we design a common bus digital audio interface that communicates with only two wires and employs the clock gear method to reduce bus power consumption. The comparison results show that the proposed common bus connection can reduce more than 30% of power consumption as compared with point-to-point connection if more than three devices are connected.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.8
• /
• pp.63-72
• /
• 1995

Closed-die forging of spur gears with hollow cylindrical billet has been analysed by using the upper-bound method. A kinematically admissible velocity field has been developed, wherein, an involute curve has been introduced to represent the forging die profile. In the analysis, the deformation region has been divided into nine zones. A constant frictional stress has been assumed on the contacting surfaces. Utilizing the formulated velocity field, numerical calculations have been carried out to investigate the effects of various parameters, such as module, number of teeth and friction factor, on the forging of spur gears. Hardness and accuracy of forged gears are measured. The following results have been obtained: (1) It is verified that an axisymmetric deformation zone exists between root circle and center of gear through forged gears. (2) The average relative forging pressure is predominantly dependent on the number of teeth and increases near the final filling stage as the addendum modification coefficient increases. (3) Close agreement was found between the predicted values of forging load and those obtained from experimental results.