• Journal of Korean Society of Environmental Engineers
• /
• v.37 no.4
• /
• pp.218-227
• /
• 2015

A prerequisite for precise quantification of nanomaterials contained in environmental samples is to prepare suitable preservation conditions of samples. This study was initiated to suggest preservation conditions of aqueous samples for analyses of metal nanomaterials. Variation in the size of silver nanomaterial (cit-AgNP) was observed according to change in various conditions, such as pH, electrolyte concentration, temperature, nanomaterial concentration, and time. Aggregation of AgNP was characterized for each environmental condition, and finally proper preservation conditions of samples were proposed based on experimental results on AgNP aggregation. In addition, the preservation period of sample was computed by the doublet time of AgNP. The results indicate that the aggregation rate of cit-AgNP was close to 0 at the conditions of pH of ${\geq}7$, electrolyte ($Ca(NO_3)_2$) concentration of ${\leq}3mM$, temperature of $4^{\circ}C$, and cit-AgNP concentration of ${\leq}2mg/L$. Furthermore, the experimental results on doublet time of cit-AgNP suggest that maximum preservation period was evaluated to be 15.79~17.53 days when the concentration of 100 nm cit-AgNP is assumed to be $1{\mu}g/L$ which is considered as an environmentally-relevant concentration of engineered nanomaterials. Our results suggest that samples should be preserved at $4^{\circ}C$ and analyzed within 2 weeks.

• Journal of Korean Society of Environmental Engineers
• /
• v.36 no.11
• /
• pp.758-763
• /
• 2014

Soil microbial fuel cells (SMFC) have gained a great attention as an eco-friendly technology that can simultaneously generate electricity and treat organic pollutants from the contaminated soil. We evaluated the effect of electrode spacing and size on the performance of SMFC treating soil contaminated with organic pollutants. Maximum power density decreased with increase in electrode distance or decrease in electrode size, likely due to higher internal resistance. The maximum voltage and power density decreased from 326 mV and $19.5mW/m^2$ with 4 cm of electrode distance to 222 mV and $5.9mW/m^2$ with 9 cm of electrode distance. In case of electrode size test, the maximum voltage and power density generated was 291 mV, $0.34mW/m^3$ when both of anode and cathode area were $64cm^2$ with 4 cm of electrode distance. The maximum voltage decreased by 19~29% when the anode area decreased to $16cm^2$ while only 3~12% of voltage decreased with cathode area decrease. The maximum power density decreased by 49~68% with decreasing anode size, and by 29~47% with decreasing cathode size. These results showed that the anode area had more significant effects than the cathode area on the power generation of SMFC which has a high internal resistance due to a coexistence of soil and wastewater in the reactor.

• Journal of Korean Society of Environmental Engineers
• /
• v.29 no.6
• /
• pp.647-653
• /
• 2007

The ultimate objective of this study is to develop a reliable oxygen-enriched combustion techniques especially for the case of the flue gas recycling in order to reduce the $CO_2$ emissions from practical industrial boilers. To this end a systematic numerical investigation has been performed, as a first step, for the resolution of the combusting flame characteristics of lab-scale LNG combustor. One of the important parameters considered in this study is the level of flue gas recycling calculated in oxygen enriched environment. As a summary of flame characteristics, for the condition of 100% pure $O_2$ as oxidizer without any flue gas recycling, the flame appears as long and thin laminar-like shape with relatively high flame temperature. The feature of high peak of flame temperature is explained by the absence of dilution and heat loss effects due to the presence of $N_2$ inert gas. The same reasoning is also applicable to the laminarized thin flame one, which is attributed to the decrease of the turbulent mixing. These results are physically acceptable and consistent and further generally in good agreement with experimental results appeared in open literature. As the level of $CO_2$ recycling increases in the mixture of $O_2/CO_2$, the peak flame temperature moves near the burner region due to the enhanced turbulent mixing by the increased amount of flow rate of oxidizer stream. However, as might be expected, the flue gas temperature decreases due to presence of $CO_2$ gas together with the inherent feature of large specific heat of this gas. If the recycling ratio more than 80%, gas temperatures drop so significantly that a steady combustion flame can no longer sustain within the furnace. However, combustion in the condition of 30% $O_2/70% $ $CO_2$ can produce similar gas temperature profiles to those of conventional combustion in air oxidizer. An indepth analyses have been made for the change of flame characteristics in the aspect of turbulent intensity and heat balance.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.18 no.2
• /
• pp.94-101
• /
• 2015

To mitigate the greenhouse gas emission, many carbon capture and storage projects are underway all over the world. In Korea, many studies focus on the storage of $CO_2$ in the offshore sediment. Assurance of safety is one of the most important issues in the geological storage of $CO_2$. Especially, the assessment of possibility of leakage and amount of leaked $CO_2$ is very crucial to analyze the safety of marine geological storage of $CO_2$. In this study, the leakage of injected $CO_2$ through fault was numerically studied. TOUGH2-MP ECO2N was used to simulate the subsurface behavior of injected $CO_2$. The storage site was 150 m thick saline aquifer located 825 m under the continental shelf. It was assumed that $CO_2$ leak was happened through the fault located 1,000 m away from the injection well. The injected $CO_2$ could migrate through the aquifer by both pressure difference driven by injection and buoyancy force. The enough pressure differences made it possible the $CO_2$ to migrate to the bottom of the fault. The $CO_2$ could be leaked to seabed through the fault due to the buoyancy force. Prior to leakage of the injected $CO_2$, the formation water leaked to seabed. When $CO_2$ reached the seabed, leakage of formation water stopped but the same amount of sea water starts to flow into the underground as the amount of leaked $CO_2$. To analyze the effect of injection rate on the leakage behavior, the injection rate of $CO_2$ was varied as 0.5, 0.75, and $1MtCO_2/year$. The starting times of leakage at 1, 0.75 and $0.5MtCO_2/year$ injection rates are 11.3, 15.6 and 23.2 years after the injection, respectively. The leakage of $CO_2$ to the seabed continued for a period time after the end of $CO_2$ injection. The ratios of total leaked $CO_2$ to total injected $CO_2$ at 1, 0.75 and $0.5MtCO_2/year$ injection rates are 19.5%, 11.5% and 2.8%, respectively.

• Journal of Biomedical Engineering Research
• /
• v.25 no.2
• /
• pp.157-163
• /
• 2004

Nitrogen ion implantation and ion plating techniques were applied for improvement of the wear resistance of metallic implant materials. In this work, the wear dissolution behaviour of a nitrogen ion implanted super stainless steel (S.S.S, 22Cr-20Ni-6Mo-0.25N) was compared with those of S.S.S, 316L SS and TiN coated 316L SS. The amounts of Cr and Ni ions worn-out from the specimens were Investigated using an electrothermal atomic absorption spectrometry. Furthermore, the Ti(Grade 2) disks were coated with TiN, ZrN and TiCN by use of low temperature arc vapor deposition and the wear resistance of the coating layers was compared with that of titanium. The chemical compositions of the nitrogen ion implanted and nitride coated layers were examined with a scanting auger electron spectroscopy. It wat observed that the metal ions released from the nitrogen ion implanted S.S.S surface were significantly reduced. From the results obtained, it was shown that the nitrogen ion implanted zone obtained with 100 KeV ion energy was easily removed within 200,000 revolutions from a wear dissolution testing under a similar load condition when applied to artificial hip joint. The remarkable improvement in wear resistance weir confirmed by the nitrides coated Ti materials and the wear properties differ greatly according to the chemical composition of the coating layers. for specimens with the same coating thickness of about 3$\mu\textrm{m}$, TiCN coated Ti showed the highest wear resistance. However, after removing the coating layers, the wear rates of all nitrides coated Ti reverted to their normal rates of below 10,000 revolutions from Ti-disk-on-disk wear testing under the same load condition. From the results obtained, it is suggested that the insufficient depth of the 100 Kel N$\^$＋/ ion implanted zone and of the nitrides coated layers of 3$\mu\textrm{m}$ are subject to restriction when used as frictional parts of load bearing implants.

• Radiation Oncology Journal
• /
• v.11 no.1
• /
• pp.35-42
• /
• 1993

The dose response of the number of micronuclei in cytokinesis-blocked (CB) lymphocytes after in vitro irradiation with $\gamma$-rays and neutrons in the 5 dose ranges was studied for a heterogeneous population of 4 donors. One thousand binucleated cells were systematically scored for micronuclei. Measurements performed after irradiation showed a dose-dependent increase in micronuclei (MN) frequency in each of the donors studied. The dose-response curves were analyzed by a linear-quadratic model, frequencies per 1000 CB cells were ($0.31{\pm}0.049$)D+($0.0022{\pm}0.0002)D^2+(13.19{\pm}1.854) (r^2=1.000,\;X^2=0.7074,\;p=0.95$) following $\gamma$ irradiation, and ($0.99{\pm}0.528$)\;D+(0.0093{\pm}0.0047)\;D^2+(13.31{\pm}7.309)\;(r^2=0.996,\;X^2=7.6834,\;p=0.11) following neutrons irradiation (D is irradiation dose in cGy). The relative biological effectiveness (RBE) of neutrons compared with $\gamma$-rays was estimated by best fitting linear-quadratic model. In the micronuclei frequency between 0.05 and 0.8 per cell, the RBE of neutrons was $2.37{\pm}0.17$. Since the MN assay is simple and rapid, it may be a good tool for evaluating the $\gamma$-ray and neutron response.

• Radiation Oncology Journal
• /
• v.27 no.4
• /
• pp.189-193
• /
• 2009

Purpose: To report on the changes in the patterns of care and survival over time for esthesioneuroblastoma. Materials and Methods: We retrospectively analyzed 42 previously untreated and histologically confirmed esthesioneuroblastoma patients seen between March 1989 and June 2007. According to Kadish's classification, 3 patients (7%) were stage A, 6 (14%) at stage B, and 33 (79%) at stage C. Of the 33 Kadish C patients, 19 and 14 patients were treated from 1989 through 2000 and from 2001 through 2007, respectively. Treatment included surgical resection, radiotherapy, chemotherapy, or a combination of these methods. Chemotherapy was administered to 8 of 19 patients (42%) seen from 1989 through 2000, whereas all of the 14 patients seen from 2001 through 2007 received chemotherapy (p<0.001). No patient was treated by three-dimensional conformal radiotherapy (3D-CRT) from 1989 through 2000, however 8 of 14 patients (67%) seen from 2001 through 2007 underwent 3D-CRT (p<0.001). The median follow-up time for surviving patients was 6.5 years (range, 2.2~15.8 years). Results: The 5-year overall survival (OS) and progression-free survival (PFS) rates for the entire cohort were 53% and 39%, respectively. The 5-year OS was 100% for Kadish stages A or B and 39% for stage C (p=0.007). For patients with stage C disease who were treated from 1989 to 2000 and from 2001 to 2007, the 5-year OS rate was 26% and 59% (p=0.029), respectively and the corresponding 5-year PFS rate was 16% and 46% (p=0.001), respectively. Intraorbital extension and treatment era (1989~2000 vs. 2001~2007) were found as independent factors for OS and PFS in a multivariate analyses. Conclusion: The results of this study suggest that treatment era, which features a distinction in treatment modality and technique with the introduction of 3D-CRT, may be the cause of improved OS and PFS in Kadish stage C patients. To achieve better outcomes for patients with Kadish stage C, combined chemoradiotherapy, especially 3D-CRT, is recommended in addition to surgery.

• Korean Journal of Weed Science
• /
• v.13 no.2
• /
• pp.104-113
• /
• 1993

The experiment was conducted in 1992 to find out the approach to the development of prediction model of weed population in paddy fields. The weed seeds of 88% over were separated from the soil by using $K_2CO_3$ 50% solution with specific gravity 1.34. The weed seeds which were floated on the solution due to the difference of specific gravity between soil particles and the seeds were effectively withdrawn by using a vaccum pump attached with an aspirator. The seeds withdrawn together with solution were taken by filtering with a nylon net of $0.31{\times}0.16mm$ mesh. The pressing method was more efficient and practical for the viability test of weed seeds separated from the soil compared with the germination test and the TTC test. For the prediction of weed population by the number of weed seedlings emerged at the sampled soil, the sampling method of 0-10cm deep at 5-6 sites per field was applicable. At the prediction method by the number of seedlings emerged, the smaller the seed sizes, the lower the prediction coefficients of weed species. It was considered that the prediction method by the number of seedlings emerged was more practical than the prediction method by the number of seeds separated from sampled soil, in relation to similarities to weed population, time and expenses required for examining, technical difficulties and applicability of weed species.

• Korean Journal of Food Science and Technology
• /
• v.39 no.4
• /
• pp.438-446
• /
• 2007

The fermented soybean product, cheonggukjang, is favored by many people, partly due to its bio-functional ingredients. Since the fermentation process of cheonggukjang is mediated by enzymes, including proteases, produced by microbes, analysis of the proteome profile changes in cheonggukjang during fermentation would provide us with valuable information for fermentation optimization, as well as a better understanding of the formation mechanisms of the bio-functional substances. The soluble proteins from cheonggukjang were prepared by a phenol/chloroform extraction method, in order to remove interfering molecules for high resolution 2-D gel analysis. Proteomic analysis of the cheonggukjang different fermentation periods suggested that most of the soluble soy proteins were degraded into smaller forms within 20hr, and many microbial proteins, such as mucilage proteins, dominated the soluble protein fraction. The proteomic profile of cheonggukjang was very different from natto, in terms of the 2-D gel protein profile. Among the separated protein spots on the 2-D gels, 50 proteins from each gel were analyzed by MALDI-TOF MS and PMF for protein identification. Due to database limitations with regard to soy proteins and microbial proteins, identification of the changed proteins during fermentation was restricted to 9 proteins for cheonggukjang and 15 for natto. From de novo sequencing of the proteins by a tandem MS/MS, as well as by database searches using BLASTP, a limited number of proteins were identified with low reliability. However, the 2-D gel analysis of proteins, including protein preparation methods, remains a valuable tool to analyze complex mixtures of proteins entirely. Also, for intensive mass spectrometric analysis, it is also advisable to focus on a few of the interestingly changed proteins in cheonggukjang.

• Korean Journal of Food Science and Technology
• /
• v.40 no.6
• /
• pp.707-711
• /
• 2008

The principal objective of the current study was to isolate a purpurogallin derivative as an oxidation product from gallic acid, in an effort to assess the anti-inflammatory effects of this compound. Purpurogallin derivative is known to be the one of the oxidation products of gallic acid. This compound has been identified as a minor chemical component in fermented tea products. It has been previously demonstrated that theaflavins, the oxidation products of catechins found in fermented tea products, exert profound antioxidant and anti-inflammatory effects. However, the biological activities of a minor chemical component in fermented teas have yet to be evaluated. Purpurogallin carboxylic acid (PCA) was identified as a major oxidation product of gallic acid from a peroxidase/hydrogen peroxide oxidation model system. The identity of the PCA was verified by $^{1}H$ NMR, $^{13}C$ NMR and MS techniques. PCA treatment significantly suppressed the generation of pro-inflammatory mediators including nitric oxide and IL-6 in lipopolysaccharide (LPS)-stimulated RAW264.7 murine macrophages. According to the nitrite assay, PCA 100, 75, and $50{\mu}g/mL$ treatment dose-dependently inhibited NO production by 57.6, 41.5, and 21.8%, respectively, in LPS-stimulated RAW264.7 murine macrophage cells. Moreover, IL-6 production was inhibited to a significant degree with PCA treatment of 100 and $75{\mu}g/mL$ at 43.1 and 23.9%, respectively. PCA treatment also significantly suppressed $PGE_2$ production at levels of 100 and $75{\mu}g/mL$. These results showed that PCA exerts inhibitory effects on the production of inflammatory mediators.