• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.41-41
• /
• 2017

본 연구는 초분광 영상을 이용하여 수박 모종의 수분함량을 비파괴적으로 추정하기 위해 수행되었다. 단계적으로 수분 스트레스를 받은 수박(n=45) 모종을 초분광 영상시스템으로 촬영하여 모종 영역의 반사율을 추출하였고, 매 촬영 후 모종의 생체중과 건물중을 측정하여 수분함량을 계산하였다. 모종의 반사율과 계측된 수분함량을 변수로 하여 Partial Least Square Regression(PLSR) 분석을 이용하여 수분 추정 모델을 구축하였다. 수분 추정모델을 작성한 결과 Calibration(Cal.)의 정확도($R^2$)는 0.66, 정밀도(RMSE 및 RE)는 각각 1.06%, 1.14%로 나타났다. 수박 모종의 수분함량 추정모델의 정밀도는 상당히 높게 나타났으나 정확도는 낮게 나타났다. 정확도를 개선하기 위해 Confidence ellipses의 신뢰구간을 95%로 설정하였을 때 3개의 모종이 타원 밖에 위치하는 것을 발견하였으며 이를 제거 후 재분석을 하였다. 3개의 모종을 제외한 수박 모종의 수분함량 추정모델의 정확도는 0.82, 정밀도는 0.73%, 0.78%로 나타났다. 3개의 모종을 제외함으로서 모델의 정확도 및 정밀도가 상승하여 3개의 모종이 정확도 및 정밀도를 낮추는 원인이라 판단된다. 작물은 가뭄스트레스를 받을수록 반사율이 낮아지지만(Yang et al., 2010) 3개의 모종은 다른 모종의 수분함량에 비해 반사율이 큰 차이를 나타내어 정확도 및 정밀도를 낮춘 것으로 판단된다. 본 연구를 통해 초분광 영상을 이용하여 수박 모종의 수분함량 추정가능성을 시사하였고, 모델의 정확도를 개선하기 위해 샘플 수 및 수분함량의 변이를 증가시키는 것이 필요하다고 판단된다.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2004.06a
• /
• pp.97-104
• /
• 2004

Double-layered polysulfone composite films, containing cerium activated yttrium silicate (CAYS) as a flour, were prepared from double casting of two polymeric solutions, and their morphology and physical strength were superior to those of single-layered composites. The prepared polymeric films consist of a dense bottom layer and a CAYS-holding top layer. The former is made of coagulating the polysulfone and methylene chloride binary solution and works as a supporter to improve the composite's physical strength, while the latter holding the inorganic fluor plays a role as an active site to detect the radioactive contamination. The prepared films revealed two distinguished, but tightly attached, double layers, their attachment being identified by morphology of the interface between two layers. As prepared by water immersion coagulation, the films have highly developed macropores, compared with a dense structure in the film prepared by evaporation. In the radionuclide detection test of the CAYS-impregnated composites, the films have reliable detection capacity at a radionuclide spotting test. The double-layered composites with the dense support layer show a better stability in holding the radionuclides spotted on the surface as well as an improvement in physical strength, compared with the single-layer composites having shortcomings such as being too porous or being brittle.

• Economic and Environmental Geology
• /
• v.40 no.4
• /
• pp.445-459
• /
• 2007

Superconducting Gravimeter(SG) was installed and has been successfully operated at MunGyung, Kyungsang province in Korea in March 2005. It was registered as the 21st observatory of the Global Geodynamics Project. Since SG can precisely measure the gravity variations below the 1mHz frequency band, it has the outstanding capability to sense and resolve many different periodic gravity components from each other. From the raw data collected between 18 March 2005 and 21 February 2006 diurnal and semi-diurnal tidal band's residual gravity components were analyzed. During this process, the instrumental noises, air pressure, and ground water corrections were carried out. Values of $-3.18nm/s^2/hPa\;and\;17nm/s^2/m$ were used respectively in the air pressure and groundwater corrections. Hartmann-Wenzel and Whar-Dehant Earth tide models were adopted to compute the residual gravity for Q1, O1, P1, K1, M2, N2, S2, K2 tidal bands. For the ocean loading correction, SCW80, FES952, and FES02 models were used and compared. As a result, FES02 ocean loading model has shown the best match for the data processing at MunGyung SG MunGyung SG gravity was compared with GRACE satellite gravity. The correlation coefficient between the two gravity after groundwater correction was 0.628, which is higher than before ground water correction. To evaluate sensitivity at MunGyung SG gravity statition, the gravity data measured during 2005 Indodesian earthquake was compared with STS-2 broad band seismometer data. The result clearly revealed that the SG could recorded the same period of earthquake with seismometer event and a few after-shock events those were detected by seismometer.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.7
• /
• pp.805-811
• /
• 2012

The reliability based design optimization (RBDO) approach requires high computing cost to consider uncertainties. In order to reduce the design cost, the single loop single vector (SLSV) approach has been developed for RBDO. This method can reduce the cost in calculating deign sensitivity by elimination of the nested optimization process. However, this process causes the increment of the instability or inaccuracy of the method according to the problem characteristics. Therefore, the method may not give accurate solution or the robustness of the solution is not guaranteed. Especially, when the function is concave, the process frequently diverges. In this research, the concept of the conjugate gradient method for unconstrained optimization is utilized to develop a new single loop single vector method. The conjugate gradient is calculated with gradient directions at the most probable points (MPP) of previous cycles. Mathematical examples are solved for the verification of the proposed method. The numeri cal performances of the obtained results are compared to those of other RBDO methods. The SLSV approach using conjugate gradient is not greatly influenced by the problem characteristics and improves its convergence capability.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.9
• /
• pp.807-814
• /
• 2013

A fundamental study on laser-tissue interaction was conducted with the aim of developing a therapeutic medical device that can remove lesions on the intestinal wall by irradiating a high-power 808-nm infrared laser light incorporated in an endoscopic system. The perforation depth was linearly increased in the range of 1~4 mm in proportional to laser output (3~12 W) and irradiation time (5~20 s). We demonstrated that the perforation depth during laser irradiation was varied according to the tissue property of each extracted porcine organ. The measurement of the temperature distribution suggests that the energy is localized in the irradiation spot and transferred to deep tissue, which protects the surrounding tissue from thermal injury. These results can be used to set the driving parameters for a laser incision technique as an alternative to conventional surgical interventions.

• Journal of Sensor Science and Technology
• /
• v.1 no.2
• /
• pp.183-194
• /
• 1992

Some silicon micromechanical structures useful in sensors and actuators have been fabricated by electropolishing or porous silicon formation technique by anodic reaction in HF solution. The microstructures were lightly doped single crystal silicon and the formation was isotropic independent of crystal directions. Porous silicon layer(PSL) was formed selectively in $n^{+}$ region of $n^{+}/n$ silicon structure by anodic reaction in concentrated HF(20-48%) solution. Characteristics of the formed PSL were investigated along with change of the reaction voltage, HF concentration and the reaction time. PSL was formed only in $n^{+}$ region. The porosity of the PSL was decreased with the increase of HF concentration and independent of reaction voltage. For the case of $n/n^{+}/n$ structures, the etched surface of silicon was fairly smooth and a cusp was not found. The thickness of the microstructures was the same as that of the epitaxial n-Si layer and good uniformity. We have fabricated acceleration sensors by anodic reaction in HF solution(5 wt%) and planar technology. The process was compatible with conventional It fabrication technique. Various micromechanical structures, such as rotors of motor, gears and linear actuator, were also fabricated by the technique and examined by SEM photographs.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.11
• /
• pp.1123-1129
• /
• 2015

A pair of two-way valves typically is used in automotive washing machines, where the water flow direction is frequently reversed and highly pressurized clean water is sprayed to remove the oil and dirt remaining on machined engine and transmission blocks. Although this valve system has been widely used because of its competitive price, its application is sometimes restricted by surging effects, such as pressure ripples occurring in rapid changes in water flow caused by inaccurate valve control. As an alternative, one three-way reversing valve can replace the valve system because it provides rapid and accurate changes to the water flow direction without any precise control device. However, a cavitation effect occurs because of the complicated bottom plug shape of the valve. In this study, the cavitation index and percent of cavitation (POC) were introduced to numerically evaluate fluid flows via computational fluid dynamics (CFD) analysis. To reduce the cavitation effect generated by the bottom plug, the optimal shape design was carried out through a parametric study, in which a simple computer-aided engineering (CAE) model was applied to avoid time-consuming CFD analysis and difficulties in achieving convergence. The optimal shape design process using full factorial design of experiments (DOEs) and an artificial neural network meta-model yielded the optimal waist and tail length of the bottom plug with a POC value of less than 30%, which meets the requirement of no cavitation occurrence. The optimal waist length, tail length and POC value were found to 6.42 mm, 6.96 mm and 27%, respectively.

• Journal of Adhesion and Interface
• /
• v.13 no.2
• /
• pp.58-63
• /
• 2012

CFRP chip is the byproduct from carbon fiber reinforced plastic (CFRP) processing. CFRP chip is not simply a waste mainly composed of fine carbon fiber and epoxy resin. CFRP chip keeps matrix to maximize their reinforcing effect. To obtain a uniform length of carbon fiber in CFRP chip, chip was chopped ina mortar. CFRP chip should be purified to get better interface adhesion. Epoxy resin on the carbon fiber was removed by $H_2O_2$ surface etching treatment. Optimal dispersion and fabrication conditions of CFRP chip embedded in phenolic resin were determined by thermal stability for fire retardant applications. CFRP chip-phenolic composite exhibits better mechanical and thermal properties than neat phenolic resin. Surface condition of CFRP chip-phenolic composite was evaluated by static contact angle measurement. Contact angle of CFRP chip-phenolic composite was greater than neat phenolic due to heterogeneous condition of fine carbon fibers. From the evaluation for fire retardant (ASTM D635-06) test, thermal stability of CFRP chip-phenolic composite was found to be improved with higher concentration of CFRP chip.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2002.02a
• /
• pp.282-288
• /
• 2002

본 연구는 상업용 규모의 쇄미선별공정에 사용할 수 있는 파이로트 규모 원통형 홈 선별기 시작기의 설계 및 제작에 필요한 기초 연구로서, 실험실용 원통형 홈 선별기를 이용하여 쇄미선별 실험을 실시하였다. 원통 회전속도, trough각도, indent 크기와 형상, 공급량을 요인으로 하여 완전립의 수거율과 순도, 쇄립의 수거율과 순도 및 선별효율을 조사하였다. 수행한 연구결과를 요약하면 다음과 같다. 1. 선별효율에 대한 원통 회전속도와 trough각도의 단독효과 및 교호작용은 1% 수준에서 유의성이 인정되었다. 원통 회전속도가 커지면trough각도 역시 그에 따라 적절히 증가시켜야만 선별효율의 저하가 방지되는 것으로 나타났다. 2. 최고 선별효율 값은 홈의 모양과 크기, 그리고 공급량에 관계없이 낮은 회전속도 (17rpm)와 중간 trough각도 (37.5$^{\circ}$또는 60$^{\circ}$)가 조합된 처리에서 나타났으며, 60~70% 범위의 높은 값을 보였다. 선별효율에 관한 원통 회전속도와 trough각도의 최적 조합은 17rpm, 37.5$^{\circ}$라고 판단된다. 3. 말발굽형 홈과 반구형 홈 간 선별효율의 차이는 없었다. 따라서, 실제 상업용 규모의 원통형 홈 쇄미선별기 개발에 있어서는 제작이 쉽고 유지.보수가 간편한 반구형 홈을 채택하는 것이 바람직할 것으로 생각된다. 길이 2.5mm이하의 미립인 쇄미의 선별에 사용할 홈의 크기는 2.5mm 보다는 약간 큰 3.0mm 정도가 되어야만 할 것으로 판단된다. 4. 공급량에 따른 선별효율의 차이는 1% 수준에서 유의성이 인정되었으며, 공급량이 작았을 때 전반적으로 선별효율이 높았다.타리 시프터를 채택, 사용하고 있었으며, 로타리시프터 사용상의 문제는 회전몸체를 지지하는 rod spring의 파손 등 구조와 관련된 것이었다. 로타리 시프터에 의한 쇄립의 선별과 제거정도는 만족할 만한 수준은 아니었다. 4. 국내 유통백미 완전립의 길이, 폭, 두께는 각각 5.02mm, 2.93mm, 2.03mm이었으며, 산물밀도와 천립중은 각각 745.3kg/m3 및 20.46g이었다. 5. RPC 백미제품의 품질경쟁력 향상을 유도하고자 현행 쇄미의 정의와 기준을 보다 강화하여 다음과 같은 쇄미 기준과 계급을 설정, 제시하였다. "완전립" - 길이가 3.75mm이상인 미립 "준완전립" - 길이가 2.5∼3.75mm인 미립 "쇄미" - 길이가 1.75∼2.5 mm인 미립 "이물" - 길이가 1.75mm이하인 미립.볼 때 상토 종자혼합비 6 : 1, 성형롤 회전속도 약 7 rpm으로 판단되며, 이 때 제조능력은 시간당 약 65 Kg(펠렛종자 약 39,000 개), 성형률 약 87 %, 종자손실률은 약 30 %, 펠렛종자 내 평균 종자수는 약 5.5 개, 완전 벼 종자 3개 이상 포함 펠렛종자 비율은 약 100 %가 될 것으로 보인다. 세포의 Androgen 생성을 촉진시키는 역할이 있는 것으로 보여진다 따라서 옻나무 유래 F는 포유동물의 생식기능에 중요하게 작용하는 것으로 사료된다.된다.정량 분석한 결과이다. 시편의 조성은 33.6 at% U, 66.4 at% O의 결과를 얻었다. 산화물 핵연료의 표면 관찰 및 정량 분석 시험시 시편 표면을 전도성 물질로 증착시키지 않고, Silver Paint 에 시편을 접착하는 방법으로도 만족한 시험 결과를 얻을 수 있었다.째, 회복기 중에 일어나는 입자들의 유입은 자기폭풍의 지속시간

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.27 no.5
• /
• pp.683-690
• /
• 2021

The ventilation system of the engine room of a ship is generally installed to supply the combustion air necessary for the internal combustion engine and to remove the heat source generated in the engine room, and it must satisfy the international standard (ISO 8861) for the design conditions and calculation standards for the ventilation of the ship engine room. The response delay of the ventilation system including the fire detector is affected by the airflow formed inside the area and the location of the fire detector. In this study, to improve the initial fire detection response speed of a fire detector installed on a fishing vessel and to maintain the sensitivity of the installed detector, the smoke behavior was simulated using the air flow field inside the engine room, the amount of combustion air in the internal combustion engine, and the internal pressure of the engine room as variables. Analysis of the simulation results showed that reducing the flow rate in the air flow field and increasing the vortex by reducing the internal pressure of the engine room and installing a smoke curtain would accelerate the rise of the ceiling of the smoke component and improve the smoke detector response speed and ventilation system.