• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.8
• /
• pp.101-108
• /
• 2004

The thermomechanical tensile characteristics were evaluated for A12024-T3 under heating rates from $1^{\circ}C/sec\;to\;30^{\circ}C/sec$ by using an infrared heating equipment to simulate aerodynamic heating. The rapid heating test results were compared with tensile test results after 1/2 hour exposure in terms of yield stress to investigate the influence of heating condition. A heating rate-yield temperature parameter was suggested for rapid heating based on time-temperature parameters, and master yield stress curve was obtained by using these parameter. These test results can be used for margin of safety of supersonic vehicle structures subjected to aerodynamic heating.

• Journal of the KSME
• /
• v.51 no.4
• /
• pp.37-40
• /
• 2011

이 글에서는 고효율 사출금형 온도제어를 위한 급속가열 및 냉각기술(Rapid mold heating and cooling)의 개요에 대해 소개하고, 국내외에 개발되어 있는 급속 금형가열 및 냉각기술의 현황 및 특성에 대해 비교분석을 제시하고자 한다.

• Journal of the KSME
• /
• v.51 no.4
• /
• pp.50-54
• /
• 2011

이 글에서는 고주파 유도가열(High-frequency induction heating)을 사용하여 사출금형 표면을 급속으로 가열하기 위한 기술을 소개하고, 국내외 적용사례(마이크로 패턴의 성형성 향상, 외관제품의 표면특성 향상 등)에 대해 소개하고자 한다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.196-199
• /
• 2009

The most important thing is to analyze the Fast Cook Off problem of the solid motor case exposed to direct flame is a heat transfer analysis. Heat causes degradation and ignition of the propellant. To archive an acceptable reaction level in Fast Cook Off, the rocket motor case generally must fail structurally prior to propellant ignition. We investigate the responses of the solid motor case exposed to Fast Cook Off by using finite element method for the thermal analysis.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.167-170
• /
• 2009

Fast cook-off test with rocket motors was performed and characteristics of the results were analyzed. The material of the motor case was carbon epoxy composite. The motor was loaded with HTPE propellants to improve the insensitive munitions characteristics. In the tests, sound pressure and heat flux sensors were used to determine the category of response according to the standard. The reaction response of all of the HTPE motors tested by fast cook-off was judged as Type V burning.

• Journal of the KSME
• /
• v.51 no.4
• /
• pp.41-44
• /
• 2011

이 글에서는 증기(steam)와 가압 열수(Pressurized heated Water)를 사용하는 급속가열/급속 냉각 성형기술에 대한 일반적인 기술적 내용을 소개하고 적용 사례에 대해 소개하고자 한다.

• Elastomers and Composites
• /
• v.44 no.4
• /
• pp.358-365
• /
• 2009

High-frequency induction is an efficient way to rapidly heat mold surface by electromagnetic induction. In the present work, high-frequency induction heating is applied to injection molding of a mobile phone cover in order to eliminate weldlines by efficiently raising the mold temperature. Through the induction heating experiments, the maximum temperature of $143^{\circ}C$ is obtained on the mold surface in 3s of heating, which is higher than the glass transition temperature of the resin material. An injection molding experiment is then performed with the aid of induction heating, from which we can successfully remove all the weldlines of the mobile phone cover. The effect of induction heating conditions such as the heating power and the heating time on the surface appearance is experimentally investigated.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.10 no.3
• /
• pp.408-418
• /
• 1986

본 연구에서는 표면은 단단하고 내면은 강인한 조직을 얻기위하여 대형 성형 탄 로울에 대하여 노에서의 급속가열 및 대기 상태에서의 자연냉각의 열처리가 수행 되어진다. 급속가열 및 냉각시 성형탄 로울 내부의 온도 분포 예측을 위하여 대류 및 복사 열전달 경계조건을 가지는 1차원 비정상 열전도 방정식이 유한 차분법을 사 용하여 해석되어졌다. 여기서 급속가열시 연소가스로 부터 기체복사에 의하여 성 형탄 로울의 바깥표면을 통하여 흡수되는 열량은

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.8
• /
• pp.5074-5081
• /
• 2015

A method for improving the warpage of the plastic part is a method of removing residual stress of the plastic product. that a non-uniform cooling are appeared in the injection molding process make uniform cooling. this study was developed the Rapid heating and cooling device used peltier module for uniform cooling. Make the Rapid heating and cooling device(RCHD), for Traditional water cooling device(TWCD) method and the Rapid heating and cooling method warpage were compared and were analyzed and the materials used amorphous ABS polymer. various warpage were compared for the process parameters such as packing pressure, packing time, resin temperature, mold temperature, In the amorphous ABS polymer, TWCD method has higher warpage than RCHD method and show the result to be a bit more uniform cooling. The distribution state of the ABS polymer was confirmed Through the Scanning electron microscope. In the TWCD method the distribution state of the polymer be densely distributed, and RCHS method be distributed wider than TWCD method. this is that injection molded parts be seen that cooling was made uniformly, As the temperature of the mold is gradually progress, Particles of the polymer is increased this is that internal stress was reduced.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.31 no.5
• /
• pp.594-600
• /
• 2007

Rapid mold heating has been recent issue to enable the injection molding of thin-walled parts or micro/nano structures. Induction heating is an efficient way to heat a conductive workpiece by means of high-frequency electric current caused by electromagnetic induction. Because the induction heating is a convenient and efficient way of indirect heating, it has various applications such as heat treatment, brazing, welding, melting, and mold heating. The present study covers an experimental investigation on the rapid heating using the induction heating and rapid cooling using a vortex tube in order to eliminate an excessive cycle time increase. Experiments are performed in the case of a steel cup mold core with various heating and cooling conditions. Temperature is measured during heating and cooling time, from which appropriate mold heating and cooling conditions can be obtained.