• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.5
• /
• pp.1407-1416
• /
• 1991

본 연구에서는 Liu의 수식화를 바탕으로 가공 경화성을 고려하여 수식화를 재 구성하고, 유한요소 프로그램을 개발하여 평면 변형 인발문제를 극한 해석함으로써, 성형에 필요한 한계 하중 및 최적 속도장을 직접적으로 구하였다.수렴되어진 최적 속도장으로 각 요송에서의 변형률 속도, 변형률 및 격자 변형등을 수치적으로 계산함 으로써 가공에 따른 변형 특성도 파악하였다. 한계 하중은 항공기 구조용 소재인 알 루미늄 6061 재료를 이용하여 판재 인발 실험을 행함으로써 얻은 결과치와 비교 검토 하였으며, 유동 특성을 관찰하기 위하여 격자 왜곡(grid distortion) 실험을 하여 얻 은 변형 패턴과 수치 계산에서 구한 격자변형 패턴을 상호 비교하였다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.3
• /
• pp.2212-2218
• /
• 2015

In order to find out the load bearing behavior of sand and clay which sustain three types of shallow footing, finite element analyses were performed. Failure zone of sand which sustain strip footing was affected by relative density of sand whereas, failure zone of clay was not affected by soil strength and it was similar to the failure zone which is considered in theory. Considering the shape of load-settlement curves obtained by numerical analyses, punching shear failure can be seen in loose sand and ultimate bearing load can not be seen in dense sand whereas, yielding point can be seen in clay. Ultimate bearing loads for sand predicted by theory were greater than those obtained by numerical analyses and ultimate bearing loads for clay predicted by theory were similar to those of numerical analyses. Ultimate bearing loads determined by 1 inch settlement criteria were slightly less than those of numerical analyses.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.1
• /
• pp.121-129
• /
• 2003

Numerical studies on bearing capacity problems of layered clay are performed for smooth and rough strip footings. The finite element method and finite difference method (FLAC) are used for computations of the bearing capacity, entire load-displacement curve and the failure mechanism. The presented results show that it is possible to analyze the bearing capacity of layered clay and to give a progressive failure mechanism clearly. To obtain high quality solutions, it is necessary to review the results on control parameters(e.g., yield function, number of calculation) and compare the results by two numerical methods.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2009.04a
• /
• pp.287-290
• /
• 2009

이 논문에서는 가압중수형(Pressurized Heavy Water Reactor) 프리스트레스 콘크리트 격납건물의 1/4 축소모델에 대한 극한내압능력과 전반적인 비선형거동에 관한 유한요소 해석을 수행하였다. 가압중수형 격납건물은 원통형 벽체와 돔으로 구성되었고, 4개의 부벽을 갖는다. 유한요소해석을 위해서 상용코드 ABAQUS를 이용하였고, 콘크리트, 철근 및 텐던에 대한 수치모델링을 작성하여 자중과 내압하중을 적용하였고, 텐던의 2% 변형률을 기준으로 극한내압능력을 평가하였다. 이때 사용된 재료모델로 콘크리트는 Concrete Damaged Plasticity 모델을 사용하였고, 철근과 텐던은 Elasto-Plastic 모델을 적용하였다. 유한요소 해석결과 콘크리트의 초기균열 0.41MPa에서 발생하였고, 극한내압은 0.56MPa 정도로 평가되었다.

• Magazine of the Korea Concrete Institute
• /
• v.10 no.2
• /
• pp.137-146
• /
• 1998

본 연구에서는 콘크리트 속에서 인장과 전단을 받는 FRP 다우얼의 거동과 파괴를 예측할 수 잇는 수리적인 파괴 해석 모델을 개발하였다. 다우얼 파괴해석 모델은 다우얼 작용과 파괴기준에 대한 두 개의 하위 모델로 구성되어 있는데 이들을 수정, 결합하여 만들어졌다. 다우얼 작용에 대한 모델로는 BEF 모델을 기초로 하여 두가지의 지수를 새로이 정의, 사용하였는데 하나는 콘크리트지지 강성을 변화시키기 위한 변위 정도 지수이고 다른 하나는 긴장된 케이블의 반력을 고려하기 위한 인장 지수이다. 인장과 전단이 작용하는 FRP다우얼의파괴 모델로는 Tsai-Hill 파괴기준이 사용되었고 이 기준을 적용하기 위하여 파괴 계수를 정의하였다. 개발된 파괴 해석 모델은 긴장된 FRP다우얼의 극한 전단력과 극한 변위를 예측하는데 사용하였고, 해석결과는 여러 인장응력을 가진 FRP 다우얼의 시험결과와 비교하였다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.1
• /
• pp.47-59
• /
• 2013

Ultimate load factors of PPWS(Prefabricated Parallel Wire Strand) sockets in main cables of suspension bridges are studied with respect to the tapered angles of the inner surface of sockets. After briefly reviewing the current design method, 15 numbers of finite element models of sockets are prepared by varying the number of wires in a strand and the tapered angles. The finite element models are updated by comparing experimental and numerical results, so that the models can reflect the real behavior of sockets. The stress distributions at the first yielding and ultimate states are analyzed by performing the incremental load analysis using ABAQUS. It is concluded that the optimized tapered angle of sockets should be determined at the specific angle between the results of verification equations of the required bonding length and stress resistance length.

• Journal of the Korean Geotechnical Society
• /
• v.22 no.9
• /
• pp.23-36
• /
• 2006

This study presents the development of a new closed-form analytical solution for the ultimate bearing capacity of an embedded wall in a granular mass. The closed-form analytical solution consists of upper and lower bound solutions (UB and LB). The calculated values from these bound solutions were compared with the author's two-dimensional laboratory wall model loading test and finite element analysis in the plastic region. The comparison showed that ultimate bearing loads from both the model test and finite element analysis are located between UB and LB. In particular, the ultimate bearing load from LB showed good agreement with the ultimate bearing load values from both the model test and finite element analysis. However, the calculated value from the conventional empirical form subjected to plane-strain conditions was shown to be much smaller than the LB.

• Journal of Korean Society of Steel Construction
• /
• v.22 no.5
• /
• pp.465-475
• /
• 2010

In the horizontally curved bridges, girders are subjected to the combined action of vertical bending and torsion due to their curvatures without any eccentric loads. As subjected to bending and torsion, the ultimate strength of steel/concrete composite box girders are limited by the diagonal tensile stress in the deck concrete induced by the St. Venant torsion. To determine the ultimate strength of composite box girders in bending and torsion and their interactions, this study conducted a 3-dimensional FEA and classical strength of materials investigation. Using ABAQUS, the FEA fully utilized advanced nonlinear analysis techniques simulating material/geometrical nonlinearity and post-cracking behaviors. The ultimate strength from numerical data were compared with theoretically derived values. Concurrent compressive stresses in the concrete deck improve the shear-resisting capacity of concrete, thereby resulting in an increased torsional resistance of the composite box girder in positive bending. The proposed interaction equation is very simple yet it provides a rational lower bound in determining the ultimate strength of concrete/steel composite box girders.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.37 no.1
• /
• pp.25-31
• /
• 2024

This paper introduces a numerical analysis model capable of evaluating CFT (Concrete-Filled Tube) columns across all time stages, incorporating creep behavior analysis and inelastic analysis to account for time-dependent behavior. The proposed model is compared with experimental results, revealing that the numerical model presented in this paper demonstrates more accurate trends than existing design criteria. Following verification, a numerical analysis is conducted for each slenderness ratio, determining the ultimate load capacity and examining the short-term and long-term sustained load behavior of the overall CFT column members.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.18 no.3
• /
• pp.277-289
• /
• 2005

The study examines the limit strength for steel cable-stayed bridges. A case studies have been performed in order to evaluate the limit strength lot steel cable-stayed bridges using nonlinear inelastic analysis approach and bifurcation point instability analysis approach, effective tangent modulus $(E_f)$ method. To realize it, a practical nonlinear inelastic analysis condoling the initial shape is developed. In the initial shape analysis, updated structural configuration is introduced instead of initial member forces for beam-column members at every iterative step. Geometric and material nonlinearities of beam-column members are accounted by using stability function, and by using CRC tangent modulus and parabolic function, respectively Besides, geometric nonlinearity of cable members is accounted by using secant value of equivalent modulus of elasticity. The load-displacement relationships obtained by the proposed method are compared well with those given by other approaches. The limit strengths evaluated by the proposed nonlinear inelastic analysis for the proposed cable-stayed bridges with tee dimensional configuration compared with those by the inelastic bifurcation point instability analyses.