• Journal of the Korean Society of Hazard Mitigation
• /
• v.11 no.2
• /
• pp.39-44
• /
• 2011

Plastic gradient from geometrically necessary dislocation(GND) can strongly affect micro-scale plastic behavior of polycrystalline solids. In this research, mechanical behavior of polycrystalline solid is investigated using the finite element method incorporating plastic gradient from GND effect. Gradient hardness coefficient and material length parameter are used to evaluate the effect of the plastic gradient on the behavior of materials. Sensitivity of the modeling parameters on the plastic gradient from GND is presented and effects of plastic gradient and material parameters on the behavior of single crystal inside a polycrystalline aggregate are investigated. It is confirmed that the plastic gradient from GND amplifies hardening response of polycrystals and affects single crystal behavior embedded in polycrystalline solids.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.6
• /
• pp.9-13
• /
• 2019

In this study, a miniature thin film-patterned heater was fabricated on a silicon substrate using semiconductor process technology and the thermal characteristics of the applied voltage, power, and temperature of the thin film heater were measured and analyzed. The temperature of the thin film pattern heater increased with increasing power, but the temperature increase rate was gradual at high power intervals. The characteristics of the high temperature section of the platinum thin film-patterned heater were analyzed using the heat resistance model under atmospheric and vacuum conditions. The thermal resistance measured in a vacuum atmosphere was 0.79 [K/mW] higher than the heat resistance value 0.69 [K/mW] in air. The temperature of the thin film pattern heater can be maintained at a low power in a vacuum rather than in air, and these results are expected to be utilized in the structural design of a thin film-patterned heater element.

• Tribology and Lubricants
• /
• v.35 no.3
• /
• pp.158-168
• /
• 2019

This paper presents the investigation of two types of rotordynamic modeling issues for 2.2 kW-class, rated speed of 1,800 rpm, squirrel-cage type induction motors. These issues include the lamination structure of rotor cores, and the radial clearance of ball bearings that support the shaft of the motor. Firstly, we focus on identifying the effects of rotor core lamination on the rotordynamic analysis via a 2D prediction model. The influence of lamination is considered as the change in the elastic modulus of the rotor core, which is determined by a modification factor ranging from 0 to 1.0. The analysis results show that the unbalanced response of the rotor-bearing system significantly varies depending on the value of the modification factor. Through modal testing of the system, the modification factor of 0.079 is proven to be appropriate to consider the effects of lamination. Next, we investigate the influence of ball bearing clearance on the rotordynamic analysis by establishing a bearing analysis model based on Hertz's contact theory. The analysis results indicate that negative clearance greatly changes the bearing static behavior. Rotordynamic analysis using predicted bearing stiffness with various clearances from -0.005 mm to 0.010 mm reveals that variations in clearance result in a slight difference in the displacement of the system up to 18.18. Thus, considering lamination in rotordynamic analysis is necessary as it can cause serious analysis errors in unbalanced response. However, considering the effect of the bearing clearance is optional because of its relatively weak impact.

• Journal of Digital Convergence
• /
• v.17 no.9
• /
• pp.39-46
• /
• 2019

This study started with the question of whether the percentage of non-aeronautical revenues at Incheon airport was extremely high when compared with other international airports. Although aeronautical revenues for the airport based on the traditional business model have the limits to grow due to various regulations, stakeholders concerned about improving the competitiveness recently have been interested in increasing non-aeronautical revenues. This study deals with the effect of non-aeronautical revenues at international airports on airport charges as the extent of airport privatization get stronger. To examine hypotheses, we collected international data from trustful sources. Finally, we conducted an empirical analysis of 178 airports worldwide. As a result, the higher the percentage of non-aeronautical revenues at international airports, the lower the airport charges were. Besides, the private equity ratio positively moderated the relationship between the percentage of non-aeronautical revenues and airport charges. Privatization of airports may offset the effects of reduced airport charges through increased commercial activity. Graphical display for moderation effect is offered to facilitate comprehension.

• Ecology and Resilient Infrastructure
• /
• v.7 no.4
• /
• pp.353-365
• /
• 2020

In this study, the characteristics of bed elevation changes of the Nakdong River when weir gates are opened were analyzed using the Hydrologic Engineering Center-River Analysis System (HEC-RAS). The study area was 292.37 km downstream of the Gudam Bridge to the Nakdong estuary of the Nakdong River. The HEC-RAS program, which is a 1D numerical analysis model, was used to simulate bed elevation changes. Simulations were conducted under two scenarios from 2017 to 2019. Scenarios 1 and 2 were devised under the conditions of a fully opened gate and during gate installation, respectively. Results confirmed that, under the conditions of Scenario 1, deposition occurred in most sections from the Hapcheon-Changnyeong weir to the Changnyeong-Haman weir (a distance of approximately 40 km). In addition, it was predicted that the flow that included sediments in the main stream of the Nakdong River was not interrupted by the weir structure and regularly produced changes in the river bed.

• Journal of the Korean Geotechnical Society
• /
• v.37 no.1
• /
• pp.5-15
• /
• 2021

The areas consisting of frost susceptible soils in cold regions, such as the Arctic area, have problems of frost heave and thaw settlement due to the seasonal air temperature changes and internal temperature of installed structures. Ground stabilization methods for preventing frost heave and thaw settlement of frost susceptible soils include trenching, backfilling and thermo-syphon. The thermo-syphon is the method in which refrigerant can control the ground temperature by transferring the ground temperature to atmosphere in the from of two-phase flow through the heat circulation of the internal refrigerant. This numerical study applied the function of these thermo-syphon as the boundary condition through user-subroutine coding inside ABAQUS and compared and analyzed the temperature results of laboratory experiments.

• The Korean Journal of Applied Statistics
• /
• v.35 no.4
• /
• pp.517-525
• /
• 2022

In the era of big data, various data mining techniques have been proposed as major analysis methodologies. As complex and diverse data is mass-produced, data mining techniques have attracted attention as a method that forms the foundation of data science. In this paper, we focused on the decision tree, which is frequently used in practice and easy to understand as one of representative data mining methods. Specifically, we analyzed the effect of the splitting method of decision trees on the model performance. We compared the prediction power and structures of decision tree models with different split methods based on various simulated data. The results show that the linear combination split method can improve the prediction accuracy of decision trees in the case of data simulated from nonlinear models with complex structure.

• Journal of the Korean Geotechnical Society
• /
• v.38 no.12
• /
• pp.29-43
• /
• 2022

Various underground facilities are being constructed to improve the urban environment. Therefore, it is more necessary than ever to reasonably evaluate the seismic response of underground utility tunnels, playing a significant part in urban infrastructure. In this study, the major features and differences of two types of existing pseudo-static analysis methods are reviewed. Each method uses a simplified 2D frame model to represent the seismic behavior of underground structures. Applying each method to a one-barrel rectangular utility tunnel in Korea, the suitability in predicting seismic responses, especially the racking deformation of the tunnel, is examined. In addition, several precautions and suggestions are provided in this study against the inattentive application of the methods to seismic evaluation of underground structures.

• Journal of the Korean Geotechnical Society
• /
• v.26 no.10
• /
• pp.49-60
• /
• 2010

Unsaturated permeability function is an important factor in the design and analysis of various unsaturated soil structures. Generally the permeability characteristics decrease as the mat ric suction increases and the trend is similar to water retention characteristics of a soil. The permeability of unsaturated soils can be obtained directly by laboratory tests or indirectly by estimation methods from other soil properties. For unsaturated soils sampled from 7 areas in KOREA, SWCCs and unsaturated permeability functions were obtained by experimental tests. The unsaturated permeability results were also compared with the unsaturated permeability functions derived from the SWCCs theoretically. However, the current estimation models of unsaturated permeability function did not express the unsaturated permeability characteristics. Therefore, the FXK-M permeability function was modified to predict more accurate permeability functions for Korean weathered soils using a correction factor that can be calculated from the air-entry value of SWCC. The new estimation model resulted in good agreements for all tested soils.

• Asia-pacific Journal of Multimedia Services Convergent with Art, Humanities, and Sociology
• /
• v.8 no.3
• /
• pp.589-596
• /
• 2018

Transportation or structure has the important role at clothing, food, and housing at modern society. If even the small crack happens and propagates at transportation or structure, the parts are fractured and they can cause a disaster. CT specimen was used in order to investigate the damage trend due to the crack propagation at this study to prevent this situation. As the material of CT specimen, the unidirectional carbon fiber reinforced plastic of the composite material in the limelight nowadays. The laminate angle designated in order of [60/-60/60/-60] was applied to the specimen model with the unidirectional fiber. As the analysis condition, the forced displacement was applied to the hole of upper part after fixing the hole of lower part. At the result of this study, the equivalent stress and shear stress was shown to be higher in order of the structural steel, copper, titanium and aluminum. This study result is thought to be utilized usefully at verifying the damage of CT specimen made of inhomogeneous material.