• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.3
• /
• pp.440-449
• /
• 1988

Small vibration displacements may be measured by optical interferometers, based on the Michelson method. The standard Michelson interferometer works well when the mirror displacements are relatively large compared to the optical wavelength. But it does not work for displacements less than approximately a quater of optical wavelength. Several multiple reflection laser interferometers, simply modified standard Michelson interferometer, have been developed to decrease the minimum detectable limits. Among these a relatively simple and easy multiple reflection system is used to measure the small vibration displacements. This multiple reflection system is constructed with a right angle prism and a convex lens. Therefore this system makes it possible to measure a vibration displacement of the small area on the vibrating structure. The fringe interpolation method and curve fitting method are used to determine accurately the small vibration displacements from the measured interference fringe patterns. Also computer simulation technique is used to check the accuracies of these method. According to the results of the computer simulation technique, the curve fitting method is more accurate than the fringe interpolation method. The optically measured results are in good agreement with those of the standard accelerometer with high accuracy and it is possible to measure the peak vibration displacement as small as 9.01nm using multiple reflection system and curve fitting method.

• Journal of the Microelectronics and Packaging Society
• /
• v.10 no.2
• /
• pp.19-26
• /
• 2003

Plastic and creep deformations of a solder joint on thermal cycle play an important role in the reliability of optical telecommunication components. Solder joint strain is increased with the thermal cycle time and it causes mis-alignments and power loss in the optical component. Furthermore, the component can be failed since the deformation exceed the limitation of the fatigue life. We applied the finite element analysis method to solve the problem of the solder joint reliability on thermal cycle. Plastic and creep deformations are calculated by the finite element method. And, the fatigue lire is predicted by using creep-fatigue prediction models with calculated strains. The temperature conditon of the analysis was referred from the Telcordia reliability schedule (-40 to 75). Also, the three ramp renditions, 1/min, 10/min and 50/min, and dwelling time were considered to analyze the differences of results.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.122-122
• /
• 2018

1. 배경 최근 IoT 기술이 발전함에 따라 각종 전자기기에 들어가는 센서들이 점점 늘어나고 있다. 특히 사용자 중심의 기기들은 기술이 발전함에 따라 집적화가 이루어지면서, 하나의 기기에서 온도, 습도, 조도 등의 다양한 정보를 처리하고 있다. 이에 따라 더 많은 기능을 사용하기 위해, 소모 전력 또한 점차 증가하고 있다. 그러나 부피는 한정되어 있어, 기존 배터리만으로는 증가하는 소모 전력을 모두 보완하기 어렵다. 또한 대표적인 사용자 중심 기기인 스마트폰에서는, 가장 많은 전력을 소모하는 부분이 점점 커지고 있다. 이에 대한 대책으로 버려지는 에너지를 수확하여 전기적인 에너지로 바꿔주는 에너지 하베스팅 기술이 각광을 받고 있다. 에너지 하베스팅 기술은 바람, 진동, 인체의 움직임 등의 기계적 에너지, 태양광, 실내등의 빛 에너지를 전기적인 에너지로 바꿔주는 기술을 말한다. 본 연구에서는 강유전체 고분자 내부에 양자점이 임베딩된 박막을 이용하여, 스마트폰에서 발생하는 빛 에너지와 손가락으로 디스플레이를 터치할 때 발생하는 기계적인 에너지를 모두 수확할 수 있는 새로운 소자를 제시하였다. 소자 내부에 있는 양자점은 빛 에너지를 산란 혹은 흡수하여 발광한 후, 고분자 내부의 전반사를 통해 양 옆에 있는 태양전지로 빛을 전달한다. 또한 컴포짓의 매트릭스를 이루고 있는 강유전체 폴리머인 P(VDF-TrFE)는 강유전 특성을 통해 마찰전기 에너지를 효율적으로 전기 에너지로 전환할 수 있다. 강유전체 특성에 의해 P(VDF-TrFE) 내부에 정렬된 Polarization은 퀀텀닷에 양자구속 스타크 효과(Quantum Confined Stark Effect)를 일으켜 더 긴 파장을 방출한다. 이렇게 바뀐 파장은 실리콘 태양전지에서 더 많이 흡수할 수 있는 영역으로 방출되어 태양전지 출력의 증가를 일으킨다. 마지막으로 실리콘 태양전지의 출력 증가를 보여줌으로써 이를 실험적으로 입증했다.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.12
• /
• pp.83-91
• /
• 1998

Fiber Bragg grating which has a blazed ang1e to the plane of incident wave generates a side-mode as well as main-mode. The side-mode has an identical characteristics with a long period grating that couples with a cladding mode, so rejects the special wavelength. We experimented on the side-mode characteristics with two fibers which Ge doped depressed index fiber and very high photosensitive H$_2$ loaded step index fiber according to the tilted angle. Also, using a phase mask equipped with rotation plate which has 0.02$^{\circ}$ resolution, we can control the bandwidth and the peak value of a total loss spectrum by aligned tilted grating in a fiber and using this, tried to compose the ASE band rejection filter of the Erbium doped fiber amplifier.

• Clean Technology
• /
• v.18 no.4
• /
• pp.331-340
• /
• 2012

Synthetic methods of colloids have been significantly developed in industry due to their significant demand for preparation of functional particles. Recently, dynamic/static microfluidic system has emerged as a promising route to the synthesis of the particles, providing precise control of physical and chemical properties such as size, shape, porosity, surface roughness, and surface functionality. These formed particles can be potentially used in various applications including medical diagnostics, photonic device, and biological industry. In addition, these particles provide a novel route to create new materials via their directed self-assembly, and it enable to study and predict the natural phenomenon by mimicking of the nature. Therefore, we describe recent progress for functional colloid particles and its applications.

• Journal of the Microelectronics and Packaging Society
• /
• v.28 no.1
• /
• pp.61-66
• /
• 2021

SnO2 has the wide bandgap which allows it to be used as the photocatalyst. There are many studies to enhance the photocatalytic properties of SnO2. In this study, 3-dimensional SnO2 aerogel was synthesized using epoxide-initiated sol-gel method for the optimal specific surface area. Also, graphene oxide (GO) was added before the gelation process of the aerogel to maximize the specific surface area. Addition of 0.5 wt% of GO would possibly enhance the specific surface area by 1.7 times compared with the bare tin oxide aerogel. Furthermore, enhanced specific surface area could degrade 67.3% of initial Rhodamine B in 120 minutes. To compare with the bare SnO2 aerogel, 0.5 wt% GO addition to SnO2 could double the reaction rate of the photocatalytic degradation.

• Korean Journal of Optics and Photonics
• /
• v.26 no.3
• /
• pp.155-161
• /
• 2015

We report the design and performance analysis of an off-axis three-mirror telescope as the fore optics for a new hyperspectral sensor aboard a small unmanned aerial vehicle (UAV), for low-altitude coastal remote sensing. The sensor needs to have at least 4 cm of spatial resolution at an operating altitude of 500 m, $4^{\circ}$ field of view (FOV), and a signal to noise ratio (SNR) of 100 at 660 nm. For these performance requirements, the sensor's optical design has an entrance pupil diameter of 70 mm and an F-ratio of 5.0. The fore optics is a three-mirror system, including aspheric primary and secondary mirrors. The optical performance is expected to reach $1/15{\lambda}$ in RMS wavefront error and 0.75 in MTF value at 660 nm. Considering the manufacturing and assembling phase, we determined the alignment compensation due to the tertiary mirror from the sensitivity, and derived the tilt-tolerance range to be 0.17 mrad. The off-axis three-mirror telescope, which has better performance than the fore optics of other hyperspectral sensors and is fitted for a small UAV, will contribute to ocean remote-sensing research.

• Journal of Astronomy and Space Sciences
• /
• v.13 no.2
• /
• pp.173-180
• /
• 1996

This paper briefly describes the KITSAT-1 and KITSAT-2 spacecrafts and presents the functions, calibration procedures and in-orbit results of the KITSAT-2 analog sun sensors have been flown as an experimental payload for the future mission. We have two constraints in their design: small size and very low power consumption due to the tight mass and power budget of the spacecraft. Two one-dimensional analog sun sensors are mounted on the top facet of the KITSAT-2 spaceraft. Each has $\pm$60 degrees of view angle and they cover 210 degree field of view in total as the 30 degree view angles are overlapped. Only the relative sun angle around the Z-axis (yaw-axis) and the spin rate of the spacecraft can be achieved as the one dimensional sun sensors are used and they are aligned with the Z-axis. The calibration formulae are obtained using the fifth order line fitting algorithm for each sun sensor on the ground and they are applied to the obtained in-orbit data. ASS-1 with silicon solar cells has maximum error of 1.5 degree and ASS-2 with silicon photocells manufactured at KAIST has maximum error of 0.5 degree except near 0 degree of sun ray incident anagle where random reflection of incident sun ray is maximum in orbit. The results are presented in chapter 4. The performance of each sun sensor and the possible mounting errors are stated in chapter 5.

• Korean Journal of Optics and Photonics
• /
• v.17 no.3
• /
• pp.248-255
• /
• 2006

Most optical security systems use a 4-f correlator, Mach-Zehnder interferometer, or a joint transform correlator(JTC). Of them, the JTC does not require an accurate optical alignment and has a good potential for real-time processing. In this paper, we propose an image encryption system using a position shift property of the JTC in the Fourier domain and a random phase image. Our encryption system uses two keys: one key is a random phase mask and the other key is a position shift factor. By using two keys, the proposed method can increase the security level of the encryption system. An encrypted image is produced by the Fourier transform for the multiplication image, which resulted from adding position shift functions to an original image, with a random phase mask. The random phase mask and position shift value are used as keys in decryption, simultaneously. For the decryption, both the encrypted image and the key image should be correctly located on the JTC. If the incorrect position shift value or the incorrect key image is used in decryption, the original information can not be obtained. To demonstrate the efficiency of the proposed system, computer simulation is performed. By analyzing the simulation results in the case of blocking of the encrypted image and affecting of the phase noise, we confirmed that the proposed method has a good tolerance to data loss. These results show that our system is very useful for the optical certification system.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.1
• /
• pp.461-467
• /
• 2021

Among the defect factors that can occur when a wafer-level lens is molded using a thermosetting material, the mold sticking problem of a molded lens during the release process can damage the molded substrate and deform the substrate at the wafer level. An experiment was conducted to examine the factors affecting the demolding force in the lens forming process. The demolding force was examined according to the coating material of the molds. The mold was surface-treated with ITO and Ti, followed by plasma treatment in an O2 atmosphere. A DLC coating was then performed, and the curing and releasability were examined. A coating method for the pull-off experiment was selected based on the results. To measure the demolding force according to the curing process conditions, a method of curing at a constant pressure and a method of curing at a constant position were applied. As a result, the TiO2 surface treatment reduced the release force. When cured by controlling the location, curing shrinkage can reduce the adhesion energy of the interface during curing, resulting in better demolding.