• Geophysics and Geophysical Exploration
• /
• v.11 no.3
• /
• pp.242-249
• /
• 2008

Recently, AVO analysis has been widely used in oil exploration with seismic subsurface section as a direct indicator of the existence of the gas. In the case of the deep reservoirs like the gas reservoirs in the East-sea, it is often difficult to observe AVO responses in CMP gathers even though the bright spots are shown in the stacked section. Because the reservoir becomes more consolidated as its depth deepens, P-wave velocity does not decrease significantly when the pore fluid is replaced by the gas. Thus the difference in Poisson's ratio, which is a key factor for AVO response, between the reservoir and the layer above it does not increase significantly. In this study, we analyzed the effects of Poisson's ratio difference on AVO response with a variety of Poisson's ratios for the upper and lower layers. The results show that, as the difference in Poisson's ratio between the upper and lower layers decreases, the change in the reflection amplitude with incidence angle decreases and AVO responses become insignificant. To consider the limitation of AVO responses shown in the gas reservoir in East-sea, the velocity model was made by simulation Gorae V structure with seismic data and well logs. The results of comparing AVO responses observed from the synthetic data with theoretical AVO responses calculated by using material properties show that the amount of the change in reflection amplitude with increasing incident angle is very small when the difference in Poisson's ratio between the upper and lower layers is small. In addition, the characteristics of AVO responses were concealed by noise or amplitude distortion arisen during preprocessing. To overcome such limitations of AVO analysis of the data from deep reservoirs, we need to acquire precisely reflection amplltudes In data acquisition stage and use processing tools which preserve reflection amplitude in data processing stage.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.17 no.2
• /
• pp.153-165
• /
• 2014

Carbon dioxide capture and storage (CCS) technology is recognizing one of method responding the climate change with reduction of carbon dioxide in atmosphere. In Korea, due to its geological characteristics, sub-seabed geological $CO_2$ storage is regarded as more practical approach than on-land storage under the goal of its deployment. However, concerns on potential $CO_2$ leakage and relevant acidification issue in the marine environment can be an important subject in recently increasing sub-seabed geological $CO_2$ storage sites. In the present study effect data from literatures were collected in order to conduct an effect assessment of elevated $CO_2$ levels in marine environments using a species sensitivity distribution (SSD) various marine organisms such as microbe, crustacean, echinoderm, mollusc and fish. Results from literatures using domestic species were compared to those from foreign literatures to evaluate the reliability of the effect levels of each biological group and end-point. Ecological effect guidelines through estimating level of pH variation (${\delta}pH$) to adversely affect 5 and 50% of tested organisms, HC5 and HC50, were determined using SSD of marine organisms exposed to the $CO_2$-induced acidification. Estimated HC5 as ${\delta}pH$ of 0.137 can be used as only interim quality guideline possibly with adequate assessment factor. In the future, the current interim guideline as HC5 of ${\delta}pH$ in this study will look forward to compensate with supplement of ecotoxicological data reflecting various trophic levels and indigenous species.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.26 no.4
• /
• pp.211-219
• /
• 2006

The UET(ultrasound excited thermography) for the ,eat-time diagnostics of the object employs an infrared camera to image defects of the surface and subsurface which are locally heated using high-frequency putted ultrasonic excitation. The dissipation of high-power ultrasonic energy around the feces of the defects causes an increase In temperature. The defect's image appears as a hot spot (bright IR source) within a dark background field. The UET for nondestructive diagnostic and evaluation is based on the image analysis of the hot spot as a local response to ultrasonic excited heat deposition. In this paper the applicability of VET for fast imaging of defect is described. The ultrasonic energy is injected into the sample through a transducer in the vertical and horizontal directions respectively. The voltage applied to the transducer is measured by digital oscilloscope, and the waveform are compared. Measurements were performed on four kinds of materials: SUS fatigue crack specimen(thickness 14mm), PCB plate(1.8 mm), CFRP plate(3 mm) and Inconel 600 plate (1 mm). A high power ultrasonic energy with pulse durations of 250ms Is injected into the samples in the horizontal and vertical directions respectively The obtained experimental result reveals that the dissipation loss of the ultrasonic energy In the vertical injection is less than that in the horizontal direction. In the cafe or PCB, CFRP, the size of hot spot in the vortical injection if larger than that in horizontal direction. Duration time of the hot spot in the vertical direction is three times as long as that in the horizontal direction. In the case of Inconel 600 plate and SUS sample, the hot spot in the horizontal injection was detected faster than that in the vertical direction

• Korean Journal of Construction Engineering and Management
• /
• v.25 no.5
• /
• pp.32-40
• /
• 2024

In the construction industry, lack of reliability in the quality of recycled aggregates, harmful substance problems, and negative consumer perceptions limit the expansion of the use of recycled aggregates. In this respect, existing studies mainly focus on the use of recycled coarse aggregates in concrete in consideration of durability. On the other hand, in the case of recycled fine aggregates, not only are there insufficient cases applied to major structures, but the scope of application is very limited due to lack of awareness. Therefore, the main purpose of this study is to present the possibility of their application in bearing and non-bearing wall structures through physical characteristics experiments of concrete bricks for masonry according to various mixing ratios of recycled fine aggregates and cement amounts. To this end, the compressive strength and absorption rate of concrete bricks were measured focusing on the mixing ratio of the recycled fine aggregate and the crushed fine aggregate and the amount of cement. As a result, it is found that it is possible to use 100% of recycled fine aggregate for 200kg/m³ of cement or 25% of crushed fine aggregate mixed with 75% of recycled fine aggregate for the same amount of cement to achieve the compressive strength of 13MPa, witch is one of the quality requirements for concrete bricks for bearing walls. In addition, it is found that to meet the strength of 8MPa, one of the quality requirements for non-bearing walls, it is sufficient to use 100% of the recycled fine aggregate for 100kg/m³ of cement. Through the absorption rate tests, it is also confirmed that the absorption rate of the concrete brick is 13% or less by meeting the required performance criteria. This means that even if recycled fine aggregate is used in the manufacture of concrete bricks, the quality standards required by KS F 4004 (concrete bricks) can be sufficiently met.

• Korean Journal of Soil Science and Fertilizer
• /
• v.31 no.2
• /
• pp.95-106
• /
• 1998

To reduce the environmental contamination and to utilize fly ash massively produced from the coal power plant every year, we synthesized the artificial zeolite using fly ash treated with alkaline, and then analyzed the mineralogical and morphological properties by X-ray, IR, and SEM. The amount of $NH_4{^+}$, $K^+$, and $H_2PO_4{^-}$ adsorbed by the fly ash and the artificial zeolite were determined with reaction time, amount of adsorbate used, ion concentrations. The results obtained from the pot experiments packed with the top soil, amended with granulated artificial zeolite which was made by treatment of 4% polyvinylalcohol, showed that CEC of the artificial zeolite was $257.7cmol^+kg^{-1}$, that was almost 36 times greater than that of fly ash. The ratio of $SiO_2/Al_2O_3$ decreased but the amount of Na increased. The physico-chemical properties analyzed by X-ray, IT, and SEM represented that the artificial zeolite synthesized had a similar morphological structure to that of the natural zeolite. The structures of the artificial zeolite had a significantly enlarged surface having a lot of pores, while the fly ash looked like spherical smooth shape with having not pores on the surface. Thus, the artificial zeolite was successfully synthesized. The results of adsorption isotherms of fly ash and artificial zeolite showed that the amount of $NH_4{^+}$, $K^+$, and $H_2PO_4{^-}$ adsorbed increased as the equilibrium concentration increased, while $NH_4{^+}$ was strongly adsorbed on the surface of fly ash and artificial zeolite than that of $K^+$. The most distinctive growth of Chinese cabbage was found from the top soil(NPK + soils + 20% of granulated artificial zeolite + 5% of compost). Therefore, we concluded that one of the most effective methods to effectively recycle a fly ash was to make the artificial zeolite as we did in this experiment.

• Journal of Sericultural and Entomological Science
• /
• v.16 no.1
• /
• pp.1-20
• /
• 1974

These studies are conducted to find out inducing factors for the non-sprouting bud which appears in the utility reclaimed hill mulberry held and to establish control method for it since 1971. The results are as follows： 1. In spring, winter bud does not germinate at all on the top of branches or does wither suddenly after or during its germination. Necrosis and browning are appeared in cortex and phloem of non-sprouting bud branch. In autumn, the deterioration of leaves, the abnormal leaves on the top of branch, and browning of veins or petioles are also observed. 2. The soil of non-sprouting bud mulberry Held were found to be sand loom derived from granite rocks. The sub soil of it was very poor in development of root system because it had hard soil and lower pore space ratio. Especially, the sub soil to bring about severe non-sprouting bud had been easily appeared with deficiency of moisture content because of high density solid. 3. Content of soil moisture was significantly lower in the severe non-sprouting bud soil than in the healthy field. The sub soil o( the healthy field contained proper moisture content. On the other hand, the sub soil of the severe non-sprouting bud held contained almost critical moisture content for wilting. 4. The depth of available soil was shallow in the non-sprouting bud than in the healthy fold. The more rate of the non-sprouting bud was severe, the more available soil depth was sallow. 5. Available boron content in soil was affected by moisture content in soil. There was. lower moisture content in the non-sprouting bud field than that in healthy fold during 5, June to 5, September. 6. There was no significant correlation between soil pH and available boron content. On the other hand, the correlation of the content of organic matter and available boron content appeared to be highly positive significance. 7. The quantity of boron was significantly contained more in healthy mulberry field (0.34∼0.43ppm) than in non-sprouting bud field (0.10∼0.28ppm). 8. Boron content in leaves and barks was significantly lower in the non-sprouting bud trees than in healthy trees. 9. The symptom of non-sprouting bud induced from boron free sand culture was similar with that arised in the non-sprouting bud field. 10. The rate of non-sprouting bud was high by the increased application of lime. Considering the facts mentioned the above, author may conclude that the non-sprouting bud of mulberry tree is caused by boron deficiency, but also it is affected by the parent rocks, organic matter, soil moisture content and lime application. 11. The non$.$sprouting bud may be completely controlled by the application of 6∼9kg borax per 10a mulberry field twice a year in spring and summer.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.10 no.1
• /
• pp.1-7
• /
• 2005

Tidal flats have been regarded to carry out transformation and removal of land-derived organic matter, and this purifying capability of organic matter by tidal flats is one of very important reasons for their conservation. However, integral biogeochemical studies on production and decomposition of organic matter by benthic microbes in tidal flats have been absent in Korea, although the information is indispensable to quantification of the purifying capability. Our major goals in this multidisciplinary research were to understand major biogeochemical processes and rates mediated by diverse groups of microbes dominating material cycles in the tidal flats, and to assess the contribution of benthic microbes to removal of organic matter and nutrients in the tidal flats. Our study sites were Ganghwa and Incheon north-port tidal flats that had been regarded as naturally well reserved and organically polluted, respectively. Our research group measured over 3 years primary production, biomass and community structure of primary producers, abundance and production of bacteria, enzyme activities, distribution of protozoa and protozoan grazing rates, rates of denitrification and sulfate reduction, early sediment diagenesis, primary production and respiration based on oxygen microelectrode. We analyzed major features of each biogeochemical process and their interactions. The results are compiled in the following articles in this special issue: An (2005), Hwang and Cho (2005), Mok et at. (2005), Na and Lee (2005), Yang et at. (2005), and Yoo and Choi (2005).

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.47 no.3
• /
• pp.167-173
• /
• 2002

This experiment was conducted to figure out the change of soil physical properties, rice growth and yield with the years of continuous cultivation in direct dry-seeding and no-tillage machine transplanting. Experiments were conducted at NHAES(National Honam Agricultural Experiment Station, RDA, Iksan, Cheon Buk Province, South Korea) with a rice variety "Dongjinbyeo" from 1995 to 2000. In no-tillage machine transplanting cultivation, organic matter in soil was higher than that on direct dry-seeding and was significantly high in topsoil. Problematic weed species were E. crus-galli B., A. keisak H., and L. japonica M. Plant height and tiller number m-2 were higher in common-tillage during the total growth duration. The highest weedy rice occurrence of 27.5% was observed in live years' continuous direct dry-seeding and followed by 6.2%, in four years', and 3.7%, in three years'. The highest yield reduction of 38% was observed in five years' continuous direct dry-seeding. The reduction may resulted from the competition between weedy rice and cultivated rice.

• Journal of Animal Environmental Science
• /
• v.17 no.2
• /
• pp.71-80
• /
• 2011

Trickling filter has been extensively studied for the domestic wastewater treatment especially for the small scale plants in rural area. The purpose of this research is to survey the physical and microbial characteristics of wood chip media and the removal efficiency of animal wastewater using wood chip trickling filter system. The trickling filtration system comprises a filtration bed packed with wood chip media having a particle dia. of 5~7cm. The method comprises natural air from the bottom of the bed. The system also comprises a control mechanism including a time a constant discharge pump for controlling supply of the wastewater into the bed. The following conclusions were obtained from the results of this research. 1. The specific surface area of wood chip was 0.4123 $m^2$/g, pore volume was 0.0947 $cm^3$/g, density was 0.49 g/$cm^3$. It has forms of parallelogram and oblong which have numerous small pore space. This wood chip has been good condition for microorganism's habitat, having very larger specific surface area by complex the three dimension structure of cellulose at wood's major ingredients. 2. The total counts of in attached aerobic microbes were ranged from $10^6$ to $10^8$ CFU/g, and anaerobes microbial numbers were from $10^4$ to $10^7$. The aerobic microbial numbers appeared to be much more than those of anaerobic microbial numbers. 3. The average efficiency of $BOD_5$ and CODcr were 74.5% and 51.5%, respectively. The removal efficiency of T-N and T-P were 61.4%, 56.2%, respectively. But SS removal levels remain 19.3%.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.36 no.1
• /
• pp.41-51
• /
• 1991

This study was conducted to determine the effect of 20 years long term fertilizations on the physical and chemical properties of paddy soil and the growth, yield, yield components and grain development of rice. Non-fertilized, PK, NK, NP, NPK, NPK + compost, NPK+straw and NPK+lime have been applied since 1968 after surface paddy soil was removed. NPK+compost and NPK+straw applications increased the content of organic matter, available P and CEC, and lime increased soil acidity and SiO$_2$ content. While chemical contents in non-fertilized treatment were low as compared with other treatments. Soil porosity was higher in NPK+straw (51.4%) and NPK+lime(53.1%) than in NPK application (49.8%). Soil hardness was highest in the NPK application and was lowest in the NPK + lime. Continuous application of straw with NPK markedly increased the content of aggregate with over 1mm(19.6%) as compared with NPK application (7.1%). Plant height, tiller number, root number, leaf area index and total dry weight were higher in the applications of compost, straw and lime with NPK than in any other treatments. Brown rice yield in non-fertilized, PK and NP applications was decreased 45, 55, 15 and 5% of that in NPK application, respectively, while application of compost, straw and lime with NPK increased the yield by 11, 14 and 4%, respectively, during 20 years. The number of differentiated rachis branchs in the application of compost, straw and lime was 17 to 21 and that in the other application was 13 to 15, whereas the degenerated rachis branchs was low in the application of compost, straw and lime with NPK. The applications having higher level of perfect rice grain such as non-fertilized, NPK+compost, NPK+straw and NPK+lime had high grain weight and had low level of white core rice, white belly rice. The white core and belly rice was highest in the NP application and notched belly rice kernel was markedly increased in NK and NP applications. The period of grain filling was 30 DAH at NP and NPK applications, 35 DAH at NK and NPK+lime, 40DAH at NPK+compost and NPK+ straw, and 45DAH at non-fertilized, respectively.