• Tunnel and Underground Space
• /
• v.29 no.4
• /
• pp.262-279
• /
• 2019

In the engineering barriers of high-level radioactive waste disposal, gases could be generated through a number of processes. If the gas production rate exceeds the gas diffusion rate, the pressure of the gas increases and gases could migrate through the bentonite buffer. Because people and the environment can be exposed to radioactivity, it is very important to clarify gas migration in terms of long-term integrity of the engineered barrier system. In particular, it is necessary to identify the hydro-mechanical mechanism for the dilation flow, which is a very important gas flow phenomenon only in medium containing large amounts of clay materials such as bentonite buffer, and to develop and validate new numerical approach for the quantitative evaluation of the gas migration phenomenon. Therefore, in this study, we developed a two-phase flow model considering the mechanical damage model in order to simulate the gas migration in the engineered barrier system, and validated with 1D gas flow modelling through saturated bentonite under constant volume boundary conditions. As a result of numerical analysis, the rapid increase in pore water pressure, stress, and gas outflow could be simulated when the dilation flow was occurred.

• Tunnel and Underground Space
• /
• v.21 no.6
• /
• pp.518-525
• /
• 2011

In this study, the natural ventilation pressure resulting from the large altitude difference which is a characteristic of high radioactive waste repository and the caloric value of the heat emitted by wastes was calculated and based on the results, natural ventilation quantities were calculated. A high radioactive waste repository can be considered as being operated through closed cycle thermodynamic processes similar to those of thermal engines. The heat produced by the heating of high radioactive wastes in the underground repository is added to the surrounding air, and the air goes up through the upcast vertical shaft due to the added heat while working on its surroundings. Part of the heat added by the work done by the air can be temporarily changed into mechanical energy to promote the air flow. Therefore, if a sustained and powerful heat source exists in the repository, the heat source will naturally enable continued cyclic flows of air. Based on this assumption, the quantity of natural ventilation made during the disposal of high radioactive wastes in a deep geological layer was mathematically calculated and based on the results, natural ventilation pressure of $74{\sim}183$Pa made by the stack effect was identified along with the resultant natural ventilation quantity of $92.5{\sim}147.7m^3/s$. The result of an analysis by CFD was $82{\sim}143m^3/s$ which was very similar to the results obtained by the mathematical method.

• Journal of the Korea Concrete Institute
• /
• v.18 no.1 s.91
• /
• pp.13-19
• /
• 2006

This paper reports the test results for shrinkage properties of low shrinkage high performance concrete developed by the authors depending on specimen size and constraint of reinforcing bar. As properties in fresh concrete low shrinkage high performance concrete(LSHPC) combined with expansive additives and shrinkage reducing admixture resulted in increase SP dosage due to loss of fluidity compared with that of control mixture concrete, while the dosage of AE agent was decreased. LSHPC exhibited higher compressive and tensile strength than control mixture concrete. For the effect of specimen size, an increase in specimen size led to a reduction of drying shrinkage. However, it was found that the autogenous shrinkage was not affected by the specimen size and measuring method. For constraint condition, an increase in the ratio of reinforcing bar caused the slight reduction in the strain of reinforcing bar, while it increased the autogenous shrinkage stress. It was seen that LSHPC was effective to reduce autogenous shrinkage by as much as 70% compared with control mixture high performance concrete.

• Tunnel and Underground Space
• /
• v.31 no.5
• /
• pp.333-359
• /
• 2021

Gases such as hydrogen and radon can be generated around the canister in high-level radioactive waste disposal systems due to several reasons including the corrosion of metal materials. When the gas generation rate exceeds the gas diffusion rate in the low-permeability bentonite buffer, the gas phase will form and accumulate in the engineered barrier system. If the gas pressure exceeds the gas entry pressure, gas can migrate into the bentonite buffer, resulting in pathway dilation flow and advective flow. Because a sudden occurrence of dilation flow can cause radionuclide leakage out of the engineered barrier of the radioactive waste disposal system, it is necessary to understand the gas migration behavior in the bentonite buffer to quantitatively evaluate the long-term safety of the engineered barrier. Experimental research investigating the characteristics of gas migration in saturated bentonite and research developing numerical models capable of simulating such behaviors are being actively conducted worldwide. In this technical note, previous gas injection experiments and the numerical models proposed to verify such behaviors are introduced, and the future challenges necessary for the investigation of gas migration are summarized.

• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.3
• /
• pp.185-190
• /
• 2016

Damages of the main engine aftmost bearing and the after stern tube bearing tend to increase due to misalignment. And as the shafting system becomes stiffer due to the large engine power, whereas the hull structure becomes more flexible due to optimization by using high tensile thin steel plates. And this is the reason that more sophisticated shaft alignments are required. In this study, the optimum shafting alignment calculation was carried out, considering the thermal expansion effect, exploiting the sensitivity index, which indicates the reasonable position of forward intermediate shaft bearing for shaft alignment. and as the main subject in this study, the elastic deformation on intermediate shaft and main engine bearings occurred by vertical load of shaft mass were examined thoroughly and analyzed allowable load of bearings, reaction influence numbers of all bearings. As the result, a reliable optimum shafting alignment was derived theoretically. To verify these results, they were referred to the engine maker's technical information of main engine installation and being used shafting alignment programs of both Korean Register of Shipping and Det Norske Veritas, their reliability were reviewed.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.12
• /
• pp.1071-1078
• /
• 2015

Numerical computations were performed to investigate the effects of pintle stroke, altitude, and bore on the performance of an external pintle thruster. Results show that under-expansion flow occurs always, independent of pintle stroke. An external pintle thruster shows good performance in that it is capable of good amount of thrust control, while aerodynamic loads are increased due to shock waves on the pintle support. When altitude is increased to 20 km, the nozzle exit velocity, Mach number, thrust as well as aerodynamic loads are increased. Bore increases aerodynamic load 5.9%, and therefore pintle shape without bore is preferred for lower aerodynamic load of a pintle in order to actuate the pintle.

• Journal of the Mineralogical Society of Korea
• /
• v.27 no.4
• /
• pp.293-299
• /
• 2014

The bentonite, a buffer material, is essential for the deep geological disposal of HLW (high-level radioactive waste), and it is important to know its characteristic long-term evolution in the underground environment. With an assumption that the concentration of aqueous copper ions will increase if copper-coated materials on a metal canister are corroded, we examined some characteristic ion-exchanges and cation release phenomena occurring in the bentonite clay (montmorillonite) interacted with aqueous Cu cations. During the interaction between dissolved copper and bentonite, Na rather than Ca cations in the expandable clay were preferentially replaced by Cu ions in the experiment. In addition, the Cu-exchanged montmorillonite was characterized by an asymmetric X-ray diffracted pattern with relatively collapsed interlayers compared to the raw sample. These results indicate that the gradual change of the original bentonite property may occur in a underground disposal condition. We are going to further study the characteristic chemical and mineralogical changes of the bentonite buffer to be used for the disposal site by conducting additional experiments.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.661-664
• /
• 2008

The structure which is located in special surroundings like ocean-environment is physically and chemically eroded by seawater or salt damage, and then concrete-structure becomes deteriorated by iron corrosion and swelling pressure which leads to remarkably decline durability due to cracks and exploitation. As a measure against salt damage, it is actively being examined to use the blended cement that controls salt damage and fix chloride in the process of hydration. In this study, therefore, to examine the property of marine concrete added admixture, marine concrete is manufactured by adding high-strength admixture(omega2000) by 0, 5, 10, and 15% to low heat-blended cement. Then it shows that the compressive strength of manufactured marine cement tends to increase and chloride penetration resistance improves.

• Journal of the Microelectronics and Packaging Society
• /
• v.24 no.1
• /
• pp.57-65
• /
• 2017

The electronic components in mobile device are composed of electronic chips and various other materials. These components become extremely thin and the constituent materials have different coefficient of thermal expansion, so that considerable warpages occurs easily due to temperature change or external load. Shadow $moir{\acute{e}}$ is non-contact, whole field technique for measuring out-of-plane displacement, but the measurement sensitivity is not less than $50{\mu}m/fringe$, which is not suitable for measuring the warpage of the electronic components. In this paper, we implemented a measurement method with enhanced sensitivity of $25{\mu}m/fringe$ by investigating and optimizing various experimental conditions of the shadow $moir{\acute{e}}$. In addition, four $moir{\acute{e}}$ fringe patterns recorded by the phase shift are processes to obtain a $moir{\acute{e}}$ fringe patterns with a sensitivity four times higher. The measurement technique is applied to small electronic components of a smart phone for measuring warpage with a high sensitivity of $5{\mu}m/fringe$ at room temperature and at the temperature of $100^{\circ}C$.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.761-764
• /
• 2008

The present study is aimed to study the effect of elevated temperatures ranging from 20 to $700^{\circ}C$ on the strain properties of high-strength concrete of 40, 60, 80MPa grade. In this study, the types of test were the stressed test and stressed residual test that the specimens are subjected to a 25% of ultimate compressive strength at room temperature and sustained during heating and when target temperature is reached, the specimens are loaded to failure. Or specimens are loaded to failure after 24hour cooling time. tests were conducted at various temperatures ($20{\sim}700^{\circ}C$) for concretes made with W/B ratios 46%, 32% and 25%. Test results showed that the relative values of elastic modulus decreased with increasing compressive strength grade of specimen and the axial strain at peak stress were influenced by the load before heating. thermal strain of concrete at high temperature was affected by the preload as well as the compressive strength.