• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.16 no.4 s.109
• /
• pp.346-354
• /
• 2006

This study shows that the system performance of a positioning system composed of a piezoelectric actuator-driven flexure guide depends largely on the preload applied on the flexure guide and the driving input amplitude. We used a flexure guided system that had an original resonant frequency of 54 Hz. Our experiment showed that we could increase the driving bandwidth above the original resonant frequency, for a case involving a large preload and a small input amplitude. Results show that there is a specific 'separation frequency' where the response of the moving mass of the flexure system decouples from the response of the piezoelectric actuator, and this specific separation frequency can be selected by a proper choice of the preload and the input amplitude. To find the separation frequency, sine sweep tests were performed. To confirm the increased system bandwidth frequency, open-loop sine tracking experiments were performed. Test results show that the system responds very well up to 130 Hz frequency higher than the original natural frequency (54 Hz).

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.6
• /
• pp.620-627
• /
• 2009

Shaking table test was carried out to obtain dynamic characteristics of TLCDs with uniform and non-uniform sections for both horizontal and vertical tubes. The input to the table is harmonic acceleration with constant magnitude. The output is horizontal dynamic force which is measured by load cell installed below the TLCD. Transfer functions are experimentally obtained using the ratio of input and output. Natural frequency, the most important design factor, is compared to that by theoretical equation for TLCDs with five different water levels. System identification process is performed for experimentally obtained transfer functions to find the dynamic characteristics of head loss coefficient and effective mass of TLCDs. It is found that their magnitudes are larger for a TLCD with non-uniform section than with uniform section and natural frequencies are close to theoretical ones.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.5
• /
• pp.1983-1989
• /
• 2012

This paper presents the stability analysis of UH-60 helicopter with external store such like chaff/flare dispenser. An external store can affect the natural frequency of the aircraft and induce the resonance, which cause the failure of structures. In this paper, therefore, Rayleigh method is used to investigate the resonance with aircraft and external store, and transmission formula is used to determine the vibration load. Structural analysis with local modeling method are performed to present the robust design of aircraft with external store. The ground and flight test are also done to verify the stability of the aircraft.

• Journal of Sensor Science and Technology
• /
• v.24 no.3
• /
• pp.169-174
• /
• 2015

In this study, we developed a system to detect the various defects in the metallic objects using the phenomenon that the defects cause the changes of the natural resonant frequencies. Our system consists of a FFT Amp, an Auto Impact Hammer, a Hammer controller and a PC. Auto Impact Hammer creates vibrations in the metallic objects when tapped on the surface. These vibrational signals are converted to the voltage signals by an acceleration sensor attached to the metallic part surface. These analog voltage signals were fed into an ADC (analog-digital converter) and an FFT (fast fourier transform) conversion in the FFT Amp to obtain the digital data in the frequency domain. Labview graphical program was used to process the digital data from th FFT amp to display the spectrum. We compared those spectra with the standard spectrum to find the shifts in the resonant frequencies of the metal parts, and thus detecting the defects. We used PCB's acceleration sensor and TI's TMS320F28335 DSP (digital signal processor) to obtain the resolution of 2.93 Hz and to analyze the frequencies up to 44 kHz.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.4 no.1
• /
• pp.63-76
• /
• 2000

구조물-지반 상호작용에서 알려진 것처럼 구조물 지진응답은 구조물하부 지반조거에 따라 영향을 받는데 UBC-97을 포함한 여러내진설계규준에서 지반사태 영향을 반영하고 있다 이 연구에서는 기초크기 기초밑 지반깊이, 입력지진 작용점 및 기초 근입깊이 등의 영향을 살펴보고 깊은 지반 위에 세워진 구조물의 평균응답스펙트럼을 UBC-97 탄성응답스펙트럼과 비교하기 위해 구조물-지반 상호작용을 고려한 지진해석을 가상 3차원 유한요소법과 부구조물법을 이용하여 1952년 Taft와 1940년 El Centro 지진기록을 주파수영역에서 수행하였다 연구결과에 의하면 기초크기는 구조물 응답에 별 영향이 없고 기초저면 지반깊이는 구조물체계의 고유주기와 최대가속도를 변경시켰다 또 입력지진의 합리적 작용점은 기초저면이라는 것이 확인되었으며 깊은 지반위에 놓인 기초의 근입은 저주기영역에서 구조물 응답을 상당히 줄어들게 하였다 한편 30m 깊은 지반위에 세워진 구조물의 평균가속도와 UBC-97 가속도를 비교한 결과 UBC-97 탄성응답스펙트럼에 의한 구조물 내진설계가 안전하지 못할 수도 있으므로 UBC-97 지진계수의 할증이 필요하다.

• Journal of the Society of Naval Architects of Korea
• /
• v.33 no.4
• /
• pp.162-174
• /
• 1996

Longline type aquaculture facilities in the open sea are based on the cable-buoy-weight mooring system. For their optimal design it is necessary to estimate tensions along the mooring lines including the attachment points of buoys and weights. However, the dynamic analysis is very complicated due to the nonlinear behaviors of the mooring lines and the effects of wave and current. In this paper, parametric studies for various buoy-weight cases are shown. Finite difference scheme is employed in obtaining eigenfrequencies in the frequency domain. Nonlinear hydrodynamic drag forces are equivalently linearized.

• Journal of Drive and Control
• /
• v.14 no.1
• /
• pp.1-7
• /
• 2017

The power train of a concrete truck mixer reducer includes differential planetary gears to get a large reduction ratio for operating the mixer drum in a compact structure. These differential planetary gears are a very important part of the mixer reducer where strength problems are the main concern. Gear bending stress, gear compressive stress and scoring failure are the main concerns. Many failures in differential planetary gears are due to the insufficient gear strength and resonance problems caused by major excitation forces such as gear mating failure in the transmission. In the present study, where the excitation frequencies are the gear tooth passing frequencies of the mating gears, a Campbell diagram is used to calculate differential planetary gear critical speeds. Mode shapes and natural frequencies of the differential planetary gears are calculated by CATIA V5. These are used to predict gear resonance failures by comparing the working speed range with the critical speeds due to the gear transmission errors of the differential planetary gears.

• Journal of Aerospace System Engineering
• /
• v.11 no.1
• /
• pp.22-27
• /
• 2017

In this paper, a walking vibration sensing system (WVS system) using a Fiber Bragg Grating sensor (FBG sensor) is proposed. The seismic part of the FBG sensor was redesigned for sensitivity enhancement. The external excitation was assumed to be the walking cycle of an adult male. The FBG seismic sensor was redesigned using CATIA and ABAQUS such that the sensor's first mode natural frequency is 3.5 Hz (which is a value near the external excitation frequency). Compared with existing walking vibration sensing systems, this newly created system improves sensitivity 15 times. It is also suitable for intrusion detection applications.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.16 no.5
• /
• pp.1-11
• /
• 1979

Since the second half of 1960's one of the information industry's most vital, yet least-well-understood areas has evolved-Data communications/Computer communications. To successfully realize this field we have to identity and reveal a variety of fundermental characteristics of communications channels and see their high reliability as prerequisites. This paper has accumulated related data from 1973 on, systematically analyzed them and provided some basic back ground and suggestions. Error rate which is the final and external characteristics of communication lines according to channal types, communication types and speed, block length and geographical difference between test points was extensively examined as well as their frequency response and d-c characteristics. The perspective of 9600BPS high speed data communications was also discussed.

• Computational Structural Engineering
• /
• v.7 no.4
• /
• pp.145-150
• /
• 1994

Seismic isolation in ordinary buildings has been successively adapted to provide flexibility for the reduction of base shear forces and its concept is accepting wide agreement in lengthening the natural, period to lessen the spectral acceleration transmitted into the structure. However, one of difficulties in implementing the innovative concept to nuclear structures is due to more severe requirements in both understanding and predicting the characteristics of isolators and the behavior of cushioned structures, Stochastic analysis has been carried out to investigate the response of base isolated nuclear containers to the random earthquake ground motion.