• Journal of Wetlands Research
• /
• v.23 no.4
• /
• pp.287-295
• /
• 2021

As facilities such as dam reservoir wetlands and agricultural irrigation reservoir wetlands are built, sedimentation occurs over time through erosion, sedimentation transport, and sediment deposition. Sedimentation issues are very important for the maintenance of reservoir wetlands because long-term sedimentation of sediments affects flood and drought control functions. However, research on resignation has been estimated mainly by empirical formulas due to the lack of available data. The purpose of this study was to calculate and compare the sediment deposition rate by developing a multiple regression model along with actual data and empirical formulas. In addition, it was attempted to identify potential causes of collapse by applying it to 64 reservoir wetlands that suffered flood damage due to the long rainy season in 2020 due to reservoir wetland sedimentation and aging. For the target reservoir, 10 locations including the GaGog reservoir located in Miryang city, Gyeongsangnam province in South Korea, where there is actual survey information, were selected. A multiple regression model was developed in consideration of physical and climatic characteristics, and a total of four empirical formulas and sediment deposition rate were calculated. Using this, the error of the sediment deposition rate was compared. As a result of calculating the sediment deposition rate using the multiple regression model, the error was the lowest from 0.21(m³km²/yr) to 2.13(m³km²/yr). Therefore, based on the sediment deposition rate estimated by the multi-regression model, the change in the available capacity of reservoir wetlands was analyzed, and the effective storage capacity was found to have decreased from 0.21(%) to 16.56(%). In addition, the sediment deposition rate of the reservoir where the overflow damage occurred was relatively higher than that of the reservoir where the piping damage occurred. In other words, accumulating sediment deposition rate at the bottom of the reservoir would result in a lack of acceptable effective water capacity and reduced reservoir flood and drought control capabilities, resulting in reservoir collapse damage.

• Korean Journal of Food Science and Technology
• /
• v.53 no.4
• /
• pp.470-478
• /
• 2021

This study was conducted to monitor residual pesticides in a total of 527 school foodservice agricultural products from 2019 to 2020 in Incheon. Pesticide residues in the samples were analyzed by the multi-residue method in the Korean food code for 373 pesticides using GC-MS/MS, LC-MS/MS, GC-ECD, GC-NPD, and HPLC-UVD. By monitoring the pesticides, 12 (2.3%) of the 527 pesticides were detected, and 2 (0.4%) samples exceeded the maximum residue limit. Twelve types of pesticides were detected in the agricultural products of carrot, chard, chili pepper, chwinamul, crown daisy, parsley, perilla leaves, and spinach. As a means of risk assessment through the consumption of agricultural products detected with pesticide residues, the proportion of estimated daily intake to acceptable daily intake was estimated in the range of 0.0000-39.7425%. Results showed no particular health risk through the consumption of school foodservice agricultural products with pesticide residues.

• Journal of Bio-Environment Control
• /
• v.28 no.3
• /
• pp.197-203
• /
• 2019

This study was carried out to investigate the effect of chlorine water and plasma gas treatment on the quality and microbial control of Latuca indica L. baby Leaf during storage. Latuca indica L. baby leaves were harvested from a plant height of 10cm. They were sterilized with $100{\mu}L{\cdot}L^{-1}$ chlorine water and plasma-gas (1, 3, and 6hours), and packaged with $1,300cc{\cdot}m^{-2}{\cdot}day^{-1}{\cdot}atm^{-1}$ films and then stored at $8{\pm}1^{\circ}C$ and RH $85{\pm}5%$ for 25days. During storage, the fresh weight loss of all treatments were less than 1.0%, and the carbon dioxide and oxygen concentrations in packages were 6-8% and 16-17%, respectively for all treatments in the final storage day. The concentration of ethylene in the packages fluctuated between $1-3{\mu}L{\cdot}L^{-1}$ during the storage and the highest concentration of ethylene was observed at 6 hours plasma treatment in the final storage day. The off-odor of all treatments were almost odorless, the treatments of chlorine water and 1 hour plasma maintained the marketable visual quality until the end of storage. Chlorophyll content and Hue angle value measured at the final storage day were similar to those measured before storage in chlorine water and 1 hour of plasma treatments. E. coli was not detected immediately after sterilization in all sterilization treatments. After 6 hours of plasma treatment, the total bacteria fungus counts were lower than the domestic microbial standard for agricultural product in all sterilization treatments. The total aerobic counts in the end storage day increased compared to before storage, whereas E. coli was not detected in all sterilization treatments. The sterilization effect against bacteria and fungi was the best in chlorine water treatment. Plasma treatment showed sterilization effects, but within a prolonged period of time. In addition, the sterilization effect decreased gradually. These results suggest that chlorine water and plasma treatment were effective in maintaining Latuca indica L. baby Leaf commerciality and controlling microorganisms during postharvest storage.

• Journal of the Korean GEO-environmental Society
• /
• v.20 no.2
• /
• pp.41-48
• /
• 2019

Soil compaction is one of the most important activities in the area of civil works, including road construction, airport construction, port construction and backfilling construction of structures. Soil compaction, particularly in road construction, can be categorized into subgrade compaction and roadbed compaction, and is significant work that when done poorly can serve as a factor causing poor construction due to a lack of compaction. Currently, there are many different types of compaction tests, and the plate bearing test and the unit weight of soil test based on the sand cone method are commonly used to measure the degree of compaction, but many other methods are under development as it is difficult to secure economic efficiency. For the purpose of this research, a portable penetration meter called the Free-Fall Penetration Test (FFPT) was developed and manufactured. In this study, a homogeneous sample was obtained from the construction site and soil was classified through a sieve analysis test in order to perform grain size analysis and a specific gravity test for an indoor test. The principle of FFPT is that the penetration needle installed at the tip of an object put into free fall using gravity is used to measure the depth of penetration into the road surface after subgrade or roadbed compaction has been completed; the degree of compaction is obtained through the unit weight of soil test according to the sand cone method and the relationship between the degree of compaction and the depth of the penetration needle is verified. The maximum allowable grain size of soil is 2.36 mm. For $A_1$ compaction, a trend line was developed using the result of the test performed from a drop height of 10 cm, and coefficient of determination of the trend line was $R^2=0.8677$, while for $D_2$ compaction, coefficient of determination of the trend line was $R^2=0.9815$ when testing at a drop height of 20 cm. Free fall test was carried out with the drop height adjusted from 10 cm to 50 cm at increments of 10 cm. This study intends to compare and analyze the correlation between the degree of compaction obtained from the unit weight of soil test based on the sand cone method and the depth of penetration of the penetration needle obtained from the FFPT meter. As such, it is expected that a portable penetration tester will make it easy to test the degree of compaction at many construction sites, and will lead to a reduction in time, equipment, and manpower which are the disadvantages of the current degree of compaction test, ultimately contributing to accurate and simple measurements of the degree of compaction as well as greater economic feasibility.

• Journal of Korean Philosophical Society
• /
• v.145
• /
• pp.351-380
• /
• 2018

In every society, citizens must decide how to punish criminals, uphold the virtue of justice, and preserve the security of the community. In doing so, the members of society must ask themselves how they will punish those who carry out the most abhorrent of crimes. Many common responses to such a question is that death is an acceptable punishment for the most severe crimes. But to draw some theoretical distinction between a crime that deserves incarceration and a crime that is so heinous that it deserves capital punishment is subject to three errors. First, what possible line could be drawn? To decide on a particular number of deaths or to employ any standard would be arbitrary. Second, the use of a line would trivialize and undermine the deaths of those whose murderers fell below the standard. Third, any and all executions still are unjust, as the State should not degrade the institution of justice and dehumanize an individual who, although he or she has no respect for other human life, is still a living person. Simply put, all murders are heinous, all are completely unacceptable, and deserve the greatest punishment of the land; however, death as punishment is inappropriate. Also, while this article arrives at the conclusion that the death penalty is an inappropriate form of punishment, I have not offered an acceptable alternative that would appease those who believe capital offenders deserve a punishment that differs in its quality and severity. This is a burden that, admittedly, I am unable to meet. I finally conclude that the death penalty is unjustified retribution. This is the only claim that can effectively shift the intellectual paradigms of the participants in the debate. The continued use of the death penalty in society can only be determined and influenced by the collective conscience of the members of that society. As stated at the outset of this article, it is this essentially moral conflict regarding what is just and degrading that forms the backdrop for the past changes in and the present operation of our system of imposing death as a punishment for crime.

• Journal of Food Hygiene and Safety
• /
• v.34 no.1
• /
• pp.30-39
• /
• 2019

An analytical method was developed for the determination of sedaxane in agricultural products using liquid chromatograph-tandem mass spectrometry (LC-MS/MS). The samples were extracted with acetonitrile and partitioned with dichloromethane to remove the interference, and then purified by using silica SPE cartridges to clean up. The analytes were quantified and confirmed by using LC-MS/MS in positive ion mode using multiple reaction monitoring (MRM). The matrix-matched calibration curves were linear over the calibration ranges ($0.001-0.25{\mu}g/mL$) into a blank extract with $r^2$>0.99. For validation, recovery tests were carried out at three different concentration levels (LOQ, 10LOQ, and 50LOQ, n=5) with five replicates performed at each level. The recoveries were ranged between 74.5 to 100.8% with relative standard deviations (RSDs) of less than 12.1% for all analytes. All values were consistent with the criteria ranges requested in the Codex guidelines (CAC/GL 40, 2003) and Food Safety Evaluation Department guidelines (2016). The proposed analytical method was accurate, effective and sensitive for sedaxane determination in agricultural commodities.

• The Journal of Korean Academy of Prosthodontics
• /
• v.57 no.3
• /
• pp.211-218
• /
• 2019

Purpose: The purpose of the present study was to compare the accuracy of four different metal copings fabricated by CAD/CAM technology and to evaluate clinical effectiveness. Materials and methods: Composite resin tooth of the maxillary central incisor was prepared for a metal ceramic crown and duplicated metal die was fabricated. Then scan the metal die for 12 times to obtain STL files using a confocal microscopy type oral scanner. Metal copings with a thickness of 0.5 mm and a cement space of $50{\mu}m$ were designed on a CAD program. The Co-Cr metal copings were fabricated by the following four methods: Wax pattern milling & Casting (WM), Resin pattern 3D Printing & casting (RP), Milling & Sintering (MS), Selective laser melting (SLM). Silicone replica technique was used to measure marginal and internal discrepancies. The data was statistically analyzed with One-way analysis of variance and appropriate post hoc test (Scheffe test) (${\alpha}=.05$). Results: Mean marginal discrepancy was significantly smaller in the Group WM ($27.66{\pm}9.85{\mu}m$) and Group MS ($28.88{\pm}10.13{\mu}m$) than in the Group RP ($38.09{\pm}11.14{\mu}m$). Mean cervical discrepancy was significantly smaller in the Group MS than in the Group RP. Mean axial discrepancy was significantly smaller in the Group WM and Group MS then in the Group RP and Group SLM. Mean incisal discrepancies was significantly smaller in the Group RP than in all other groups. Conclusion: The marginal and axial discrepancies of the Co-Cr coping fabricated by the Wax pattern milling and Milling/Sintering method were better than those of the other groups. The marginal, cervical and axial fit of Co-Cr copings in all groups are within a clinically acceptable range.

• The Journal of Korean Academy of Prosthodontics
• /
• v.57 no.3
• /
• pp.203-210
• /
• 2019

Purpose: The purpose of this study was to verify the effect of the abutment superimposition process on the final virtual model in the scanning process of single and 3-units bridge model using a dental model scanner. Materials and methods: A gypsum model for single and 3-unit bridges was manufactured for evaluating. And working casts with removable dies were made using Pindex system. A dental model scanner (3Shape E1 scanner) was used to obtain CAD reference model (CRM) and CAD test model (CTM). The CRM was scanned without removing after dividing the abutments in the working cast. Then, CTM was scanned with separated from the divided abutments and superimposed on the CRM (n=20). Finally, three-dimensional analysis software (Geomagic control X) was used to analyze the root mean square (RMS) and Mann-Whitney U test was used for statistical analysis (${\alpha}=.05$). Results: The RMS mean abutment for single full crown preparation was $10.93{\mu}m$ and the RMS average abutment for 3 unit bridge preparation was $6.9{\mu}m$. The RMS mean of the two groups showed statistically significant differences (P<.001). In addition, errors of positive and negative of two groups averaged $9.83{\mu}m$, $-6.79{\mu}m$ and 3-units bridge abutment $6.22{\mu}m$, $-3.3{\mu}m$, respectively. The mean values of the errors of positive and negative of two groups were all statistically significantly lower in 3-unit bridge abutments (P<.001). Conclusion: Although the number of abutments increased during the scan process of the working cast with removable dies, the error due to the superimposition of abutments did not increase. There was also a significantly higher error in single abutments, but within the range of clinically acceptable scan accuracy.

• Journal of Food Hygiene and Safety
• /
• v.34 no.3
• /
• pp.283-289
• /
• 2019

This study was performed to monitor the residual pesticides in agricultural products used in school foodservice in the Gwangju metropolitan area. Risk assessment was also carried out based on the amount of agricultural products consumed. A total of 320 agricultural products supplied to schools in Gwangju were analyzed from 2015 to 2017. The pre-treatment and residual pesticide analysis of these products was conducted in accordance with the second method for multi-residue analysis of pesticides in the Korean food code. The hazard index was calculated by dividing the estimated daily intake (EDI) of pesticides by the acceptable daily intake (ADI). The linearity correlation coefficient for the calibration curve was 0.9923 to 1.0000, LOD 0.004 to 0.019 mg/kg, LOQ 0.012 to 0.057 mg/kg, and recovery was 79.1 to 100.2%. Residual pesticides were detected in 18 (5.6%) of 320 agricultural products used for school foodservice, and one sample of sweet potato stem (0.3%) exceeded the maximum residual limit (MRL). The detection frequency for chili peppers and bell peppers was higher than that for other agricultural products. The frequently-detected pesticides were boscalid and acetamiprid. These results showed that residual pesticide management is needed for chili pepper, bell pepper and sweet potato stem among agricultural products supplied to schools. The hazard index of bifenthrin in sweet potato stem showed the highest (64.18%), and the other pesticides were 0.03-8.23%. These results indicated that agricultural products supplied to schools in Gwangju were safe for consumption. To minimize the intake of residual pesticides, it is necessary to not only thoroughly wash agricultural products but to also ensure the expanded supply of products that are pesticide-free.

• Journal of Food Hygiene and Safety
• /
• v.34 no.3
• /
• pp.219-226
• /
• 2019

This study was conducted to understand the overall status of the monitoring program for pesticide residues in foods of South Korea. Further propositions for its improvement were made, and from this study, the status on this program can be summarized as follows. In South Korea, the Ministry of Food and Drug Safety (MFDS) is responsible for overall control of pesticide residue monitoring. Depending on the time of monitoring (sampling at distribution or production step), the government agency responsible for monitoring is different: MFDS, Regional Offices of Food and Drug Safety and local governments are responsible for monitoring of foods at the distribution step, while the National Agricultural Products Quality Management Service (NAQS) and local governments are responsible for monitoring of foods in the production step (partially at sale and distribution steps). According to purpose of monitoring, domestic monitoring programs could be divided into two types: MFDS's "Residue Survey" and NAQS's "National Residue Survey" are conducted mainly for risk assessment purposes and various monitoring programs by the Regional Offices of Food and Drug Safety and local governments are conducted mainly for regulation purposes. For imported foods, monitoring should be conducted at both steps of customs clearance and distribution: the MFDS and the Regional Offices of Food and Drug Safety are responsible for the former, and for the latter, local governments are also responsible. However, it appeared that systematic and consistent monitoring programs are not being conducted for imported foods at the distribution step. Based on the information described above and more detailed information included in this paper, the following proposals for improving the monitoring program were forwarded: i) further clarification of monitoring program purpose, ii) strengthening of the monitoring program for imported foods, iii) providing the public with monitoring results by publication of an annual report and database. It is thought that exhaustive review on the pesticide residue monitoring program and efforts for its improvement are needed in order to assure both food safety and the success of the recently begun positive list system (PLS).