• International Journal of Highway Engineering
• /
• v.3 no.2 s.8
• /
• pp.91-102
• /
• 2001

On the basis of several experiments peformed, Bahia et al. (1998) concluded that the current Superpave PG-grading system failed to characterize grading specification of fill modified binders. This conclusion motivates us to investigate the correct grating system suited for modified asphalt binders. The main concept of this development is originated from the relationship between rut depth and binder properties at high temperatures. A new grading system for modified asphalt binders suggested here somewhat resembles to the unmodified binder grading one developed by Huh et al. (2000). Thus, this investigation will provide a unified single theoretical equation of high temperature grading that can apply both to modified and unmodified binders, and will check its effectiveness with the laboratory and the field rut data reported by independent studies. Successful results observed may allow to construction of a correct grading system in the near future.

• International Journal of Highway Engineering
• /
• v.4 no.3 s.13
• /
• pp.43-49
• /
• 2002

Asphalt pavements have to perform under the conditions of heavily-loaded vehicles due to the industrialization and large temperature variance between the summer and the winter. Due to these factors, a characteristics change of early permanent deformation becomes a big issue, and to remedy this problem many research to use modified asphalt are being widely conducted. However, most of the modified asphalt is being paved after milling the surface course and applying tackcoating, and it is being used mostly for the repair and maintenance purpose rather than pavement of new national road. The purpose of this investigation is to obtain some fundamental data for the evaluation of the performance and long-term performance of the construction material mixtures by the laboratory test and field experiments. For the field experiment, 200m of two-lanes national road, that is being paved for the new national road under the direction of Pusan Regional Construction Management Office, was paved with SBS PMA and PSMA asphalt mixtures, which are an modified asphalt mixtures used for the surface course, on top of the base course paved with other modified asphalt mixtures. The remaining section of the new national road was paved with dense grade mixture. The laboratory tests assessed and analyzed the mixture characteristics by Marshall's stability test, strength tests and wheel-tracking test. On the basis of the evaluation result of the temperature control and roughness of the newly constructed road at the field experiment site, it is desired to evaluate and identify the most economic modified asphalt mixtures by long-term performance evaluation and LCC(Life Cycle Cost) analysis in order to apply the test result to the design of new road construction in the future.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.4 no.4
• /
• pp.489-495
• /
• 2016

In this study, the Warm-Mix Asphalt was prepared using a modified Sulfur Binder mixed with an additive of a polymer component in sulfur, which is an industrial by-product generated in the crude oil refining process. The dynamic stability and durability characteristics of the prepared Warm-Mix Asphalt was evaluated by the indirect tensile strength, the tensile strength ratio before and after water immersion and freezing-thawing, and the dynamic stability by wheel tracking test. The Warm-Mix Asphalt Mixtures using Modified Sulfur Binder has a tensile strength ratio before and after water immersion of 0.88, which is about 1.13 times that of the Warm-Mix formed modified Asphalt, and the tensile strength ration before and after freezing-thawing is also 0.82, thus, all tensile strength ratios satisfied the KS quality standard value of 0.75 or more. The indirect tensile strength was 1.6MPa which was twice the KS quality standard value of 0.8MPa, and about 1.24 times higher than that of normal heated asphalt 1.29MPa. In addition, the dynamic stability by the wheel tracking test was 14,075 times/mm, which was about 15 times higher than that of normal heated asphalt and about 3 times higher than that of the Warm-Mix formed modified Asphalt, showing excellent resistance to plastic deformation such as fatigue cracks.

• Polymer(Korea)
• /
• v.31 no.1
• /
• pp.68-73
• /
• 2007

This study is on the synthesis of reactive polymer modifiers by emulsion polymerization to improve properties of asphalt for paving. Styrene, methyl methacrylate (MMA), isoprene and glycidyl methacrylate (GMA) which has epoxy ring to react with carboxyl group of asphaltene were used to synthesize polymer modifiers. Modifiers with various composition were tested miscibility with asphalt. Modifiers which showed good miscibility with asphalt were investigated by DSC for $T_g$. Existence of epoxy rings and their reaction with asphaltene wore investigated by FTIR. Molecular structures of synthesized modifiers were confirmed by $^1H-NMR$. The synthesized modifiers which showed good miscibility had their $Tg's$ in the range of $37.5{\sim}56.5^{\circ}C$ and had isoprene contents of 30 wt%. They showed good miscibility in the 1 and 2 wt% concentrations, but not in the 3 wt% concentration.

• International Journal of Highway Engineering
• /
• v.3 no.3 s.9
• /
• pp.119-133
• /
• 2001

The stiffness of chemcrete modified asphalt mixtures increase rapidly with time in the presence f oxygen and high temperature, Sometimes the asphalt pavements that have chemcrete modified asphalt mixture applied on the surface none show premature cracking because of the excessive increase in the stiffness f the asphalt mixtures. To mitigate this premature cracking, the chemcrete modified mixtures have been used as a base course material. In this study, the performance of the chemcrete modified asphalt binder and mixtures are investigated through a course of various laboratory tests including dynamic shear rheometer and bending beam rheometer tests for binders and uniaxial tensile fatigue, wheel tracking, and moisture damage tests for the mixtures. And also the resilient modulus of the conventional and chemcrete modified mixtures are compared based on the test results conducted on the specimens obtained from various in-situ test sections. It can be concluded from the tests results that the chemcrete modified mixtures show better rutting resistance than conventional mixtures. The chemcrete modified mixtures may have low temperature cracking when it is applied in the cold region. The stiffness of chemcrete modified mixtures is approximately 50 percent higher than that of conventional mixtures more than two years after the chemcrete modified mixture was applied in the base course.

• International Journal of Highway Engineering
• /
• v.11 no.3
• /
• pp.33-40
• /
• 2009

The use of the crumb rubber as an asphalt binder modifier may contribute to road maintenance and repair. The adhesion properties of the crumb rubber modified asphalt (CRMA) sealant have attracted interest due to brittle and adhesion failure of asphalt binders at low temperatures. In this study, the influence of a flexibilizer as a modifier for CRMA at low temperatures was investigated. Their properties were measured using the penetration, the softening point, the tensile and tensile adhesion tests at low temperature. The tensile adhesion strength and the strain of CRMAs were increased with increasing ductile deformation of the CR and the asphalt binder in the flexiblizer modified CRMAs. It was found that the flexibilizer concentration was an important factor for tensile and adhesion properties of CRMAs at low temperatures.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.4 no.1
• /
• pp.68-75
• /
• 2016

The present study evaluated the mechanical properties of open graded asphalt for semi-rigid pavements in order to determine the mixing proportion experimentally. A total twelve types of basic mixing proportions were set up and mechanical tests such as marshall stability, porosity, permeability, and cantabro loss were conducted based on Korean standards. From the tests results, it was found that the marshall stability in case of straight and modified asphalt increase up to the contents with 5.0% and 5.5% respectively. The porosity and permeability of asphalt tended to decrease as the asphalt contents increase, the coefficient of correlation between both were estimated 86%. The increase contents with asphalt range from 3.5% to 6.0% tended to decrease the cantabro loss and the modified asphalt enhanced the resistance of cantabro loss with range from 18.8% to 33.1% than straight asphalt under same asphalt contents. In comparison with test results and quality standards, it was concluded that the modified asphalt content of 4.5% is effective to adopt for open graded asphalt.

• International Journal of Highway Engineering
• /
• v.8 no.4 s.30
• /
• pp.101-113
• /
• 2006

Generally, asphalt binder modifier increases the viscosity at high temperature as well as at mixing and paving temperature, so that higher temperature is required to produce the hot-mix asphalt. Otherwise, wax is able to improve workability by means of decreasing the viscosity of asphalt binder. In this study, the effect of PE wax used to modify the asphalt binder was evaluated in laboratory. The properties of PE wax modified binder were compared with those of SBS and Crumb Rubber Modified binders. The results showed that wax type I has an effect on strengthening rut resistance as well as improving workability. However, wax type I weaken crack resistance due to making binder harder at intermediate temperature. The results also showed that wax type II has an effect on improving workability and on strengthening crack resistance due to making binder softer.

• Elastomers and Composites
• /
• v.45 no.3
• /
• pp.217-222
• /
• 2010

Paved roads are suffered from the permanent plastic deformation in hot summer and cracks in cold winter, which are detrimental to safe driving. This leads to necessity of modification of asphalt to resist those deformation. In this study, two kinds of modifiers were examined; organic polymers and a photoinitiator which is activated by ultraviolet lay. The mechanical and rheololgical properties of modified asphalts were examined using UTM and rheometer. Results showed that the properties were varied depending on the types of polymer and irradiation time. UV irradiation increased the tensile strength and storage modulus of thermoplastic polymer-modified asphalt, however UV was not effective on thermoset polymer. According to long term ultraviolet curing test, properties of the polymer/photoinitiator-modified asphalt did not decrease, but rather increase for 20 years. This indicates that the useful life of the asphalt could be extended by addition of photoinitiator.

• International Journal of Highway Engineering
• /
• v.3 no.1 s.7
• /
• pp.185-197
• /
• 2001

This paper dealt with modification of effective crack length model (ECM) by adding Poisson's ratio term to evaluate fracture toughness of asphalt concrete which varies its material property by temperature. The original ECM model was developed for solid materials, such as cement concrete, and Poisson's ratio of materials was not considered. However, since asphalt concrete is sensitive to temperature variation and changes its Poisson's ratio by temperature, it should be taken into consideration to know exact fracture property under various temperatures. Four binders, including 3 polymer-modified asphalt (PMA) binders, were used to make a dense-grade asphalt mixture and 3-point bending test was peformed on notched beam at low temperatures, from -5oC to 35oC. Elastic modulus, flexural strength and fracture toughness were obtained from the test. The results showed that, since Poisson's ratio was considered, the more accurate test values could be obtained using modified ECM equation than original ECM. PMA mixture showed higher stiffness and fracture toughness than normal asphalt mixture under very low temperatures.