• Journal of the Korea Concrete Institute
• /
• v.25 no.2
• /
• pp.175-185
• /
• 2013

Currently in precast concrete construction, precast concrete and cast-in-place concrete with different concrete strengths are used. However, current design codes do not provide shear design methods for PC-CIP hybrid members using dual concrete strengths. In the present study, the shear strengths of beams using dual concrete compressive strengths (24 MPa, 60 MPa) were tested. The test variables were the area ratio of the two concretes, longitudinal bar ratio, and shear span-to-depth ratio. The shear strengths of test specimens were evaluated by current design methods, using an effective concrete strength (considering the area ratio of the two concrete strengths). The test result showed that when 60 MPa concrete was used in the compressive zone and the longitudinal bar ratio was low, the shear strengths of the test specimens were less than the predictions. On the basis of the results, design recommendations were provided for the shear design of the PC-CIP hybrid beams.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.14 no.5
• /
• pp.110-118
• /
• 2010

This research dealt with the effect of steel-fiber reinforcement on the compressive strength of ultra high performance cementitious composites (UHPCC) and compared with that in normal steel-fiber reinforced concrete(SFRC). With wide range of compressive strength of UHPCC, experiments on the fiber reinforcement effect confirmed that the compressive strength in UHPCC is also improved by adding fibers as in normal SFRC. The experimental results were compared with previous researches about reinforcement effect by adding fibers, which are limited within 100MPa compressive strength. The comparison revealed the linear relationship between $f'_{cf}-f'_c$ and RI regardless of the magnitude of compressive strength, from which a general equation to express the effect of fiber reinforcement, applicable to various SFRC's with wide range of compressive strength including UHPCC.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.4A
• /
• pp.267-279
• /
• 2009

A numerical model that can simulate the nonlinear behavior of ultra high strength fiber reinforced concrete (UHSFRC) structures subjected to monotonic loading is introduced. The material properties of UHSFRC, such as compressive and tensile strength or elastic modulus, are different from normal strength reinforced concrete. The uniaxial compressive stress-strain relationship of UHSFRC is designed on the basis of experimental result, and the equivalent uniaxial stress-strain relationship is introduced for proper estimation of UHSFRC structures. The steel is uniformly distributed over the concrete matrix with particular orientation angle. In advance, this paper introduces a numerical model that can simulate the tension-stiffening behavior of tension part of the axial member on the basis of the bond-slip relationship. The reaction of steel fiber is considered for the numerical model after cracks of the concrete matrix with steel fibers are formed. Finally, the introduced numerical model is validated by comparison with test results for idealized UHSFRC beams.

• Journal of Korean Society of Steel Construction
• /
• v.19 no.6
• /
• pp.575-585
• /
• 2007

In this study, a new design equation was presented for square CFTs with high-strength concrete subjected to axial compression and bending. In a previous study, a design equation for square CFTs with normal strength concrete was proposed. A parametric study by fiber analysis was performed taking the width-to-thickness ratio (b/t) and the relative concrete strength to the yield strength of the steel tube (fck/Fy) as the main parameters of this study to determine the maximum moment and the axial load at the maximum moment. A new constitutive model for concrete was adopted for fiber analysis in order to take into account the effect of high-strength concrete. The results of the parametric study were embedded into the method which was presented in the previous study to formulate a new design equation that can be easily used for estimating the strength of square CFTs with high-strength concrete.

• Journal of the Korea Concrete Institute
• /
• v.20 no.6
• /
• pp.731-739
• /
• 2008

To evaluate the fiber orientation characteristics and estimate its effect on the flexural strength of steel fiber reinforced ultra high strength concrete with directions of concrete placing, we developed an image processing technique and carried out the flexural test to quantify the effect of fiber orientation characteristics on the flexural strength as well. The image processing technique developed in this study could evaluate quantitatively the fiber orientation property by the use of dispersion coefficient, the number of fibers in a unit area, and fiber orientation. It was also found that the fiber orientation characteristics were dependent on the direction of concrete placing. Fiber orientation characteristic was revealed to strongly affect the ultimate flexural strength, while hardly affecting the first cracking strength. Theoretical model for flexural strength was applied to compare with test results, which exhibited a good agreement.

• Journal of the Korea Concrete Institute
• /
• v.25 no.5
• /
• pp.547-554
• /
• 2013

This study was intended to estimate the bond strength of steel fiber in UHPFRC through pullout test. The pullout test was carried out with the double-sided pullout specimens with multiple fibers. First, the effect of fiber density on the bond strength was investigated, and the experimental result presented that the density range considered in this study was proved not to produce fiber-to-fiber interaction. The bond strength was estimated from several methods, which are based on the pullout load or energy at peak load, and the total energy absorbed until fibers are pulled out completely. the estimated bond strength obtained from the total energy was shown to be under the influence of the embedded length of fiber. the bond strengths obtained from peak load condition was 6.64 MPa in average, which had little difference compared to 6.46 MPa calculated by peak load only. Considering simplicity of test and analysis, it may be no matter to estimate the bond strength from peak load in pullout test.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.8 no.2
• /
• pp.183-189
• /
• 2020

The purpose of this study is to investigate the compressive and tensile properties of high volume slag cement-based fiber-reinforced composite incorporating phase change material. Four mixtures were determined according to calcium hydroxide and expansive admixture, and the compressive strength and tension tests were performed. Test results showed that four mixtures showed a compressive strength over 51MPa and a tensile ductility over 3.2%. It was observed that calcium hydroxide and expansive admixture influenced the compressive and tensile performance, and the strength, ductility, and cracking patterns of composite could be improved by including proper amount of calcium hydroxide and expansive admixture.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2023.05a
• /
• pp.275-275
• /
• 2023

기후변화는 우리의 현실로 다가와 있지만 기후변화로 인해 어떠한 일이 벌어질 것인지는 정확하게 알 수 없는 문제가 있다. 특히 호우의 강도와 지속시간 등은 수문설계에 영향을 미치는 주요한 인자 임에도 불구하고 과학적이고 합리적인 추론이 쉽지 않다. 본 논문에서는 일본에서 대규모 기후 앙상블 모의실험 기반으로 생성된 d4PDF(Data for Policy Decision Making for Future Change)자료 중 시간 단위의 강수앙상블 모의 자료를 이용하여 기상청 서울지점의 강우강도-지속시간-생기빈도 곡선(Intensity-Duration-Frequency Curve; IDF 곡선)의 변화를 추정해 보았다. 이를 위하여 대용량의 자료를 확보하고 서울지점에서의 과거 50년간의 실측자료와 동일기간의 모의자료에 대한 연최대치 계열에 분위사상법을 적용하여 모의자료의 계통적 오차를 소거할 수 있는 함수를 추정하고 이를 이용하여 미래 시나리오에 적용함으로써 지구평균기온 상승에 대응하는 서울관측지점의 IDF 곡선을 추정하여 제시하였다. 추정 결과의 내용은 다양한 요소에 의해 영향을 받는 미래 기후에 대한 내용이라 신뢰성의 평가가 어렵지만 기존의 강우강도에 일률적으로 위험률을 곱하는 방식보다는 좀 더 합리적인 방법이라 생각되며 향후 수문설계 등에 고려될 수도 있을 것이다.

• Journal of the Korean earth science society
• /
• v.27 no.4
• /
• pp.433-449
• /
• 2006

Temporal and spatial variations of precipitation in South Korea are investigated using 60 observation data of the recent 30-years from 1976 to 2005. The area averaged annual precipitation amount is about 1310 mm and shows a strong spatial variation, maximum at the southern and Kyoungki province (>1300 mm) and minimum at the Kyungpook province(<1100 mm). The precipitation days show a strong spatial variation with maximum at the Sobaik mountain region(>100 days) and minimum at the Kyungpook province (<90 days). The interannual variations (IAV) of precipitation amount and days are more significant at the southern and eastern part of Sobaik and Taebaik mountain, and along the Sobaik mountain, respectively. So, the difference of annual precipitation amount reaches to about 800mm between wet and dry years at the southern part of Korean peninsula. Whereas, the IAV of precipitation intensity is strong at the southern and middle part of South Korea with a minimum between two maxima. Also, seasonal variations are closely linked with the geographic environments (elevation, distance from ocean, location relative to the Taebaik mountain). Therefore, maximum and minimum of seasonal variations of precipitation are occurred at the northern inland region (ratio of summer to the annual precipitation (RSAP) is greater than 60%), eastern and southern coastal regions (RSAP is less than 53%),respectively. And the RSAP is slightly increased from 50% to 55% comparing the Ho and Kang (1988). The consistent and strong positive relation between the heavy rainfalls, the ratio of heavy rainfalls to annual precipitation and the annual precipitation indicates that heavy rainfall is more frequent and strong at the maximum annual precipitation region.

• Journal of the Korean earth science society
• /
• v.40 no.6
• /
• pp.572-583
• /
• 2019

In this study, the atmospheric vertical structure (AVS) associated with summertime (June, July, and August) heavy rainfall in Seoul was classified into three patterns (Loaded Gun: L, Inverted V: IV, and Thin Tube: TT) using rawinsonde soundings launched at Osan from 2009 to 2018. The characteristics of classified AVS and precipitation property were analyzed. Occurrence frequencies in each type were 34.7% (TT-type), 20.4% (IV-type), 20.4% (LG-type), and 24.5% (Other-type), respectively. The mean value of Convective Available Potential Energy (1131.1 J kg^-1) for LG-types and Storm Relative Helicity (357.6 ㎡s^-2) for TT-types was about 2 times higher than that of other types, which seems to be the difference in the mechanism of convection at the low level atmosphere. The composited synoptic fields in all cases showed a pattern that warm and humid southwesterly wind flows into the Korean Peninsula. In the cases of TT-type, the low pressure center (at 850 hPa) was followed by the trough in upper-level (at 500 hPa) as the typical pattern of a low pressure deepening. The TT-type was strongly influenced by the low level jet (at 850 hPa), showing a pattern of connecting the upper- and low-level jets. The result of analysis indicated that precipitation was intensified in the first half of all types. IV-type precipitation induced by thermal instability tended to last for a short term period with strong precipitation intensity, while TT-type by mechanical instability showed weak precipitation over a long term period.