• Proceedings of the Korea Information Processing Society Conference
• /
• 2012.04a
• /
• pp.950-952
• /
• 2012

음원 위치추정 시스템은 일반적으로 여러 개의 마이크에서 수집된 음원의 시간 간격을 이용해 음원의 위치를 추정하는 방식을 적용한다. 본 논문에서는 감시카메라에 적합한 4개의 마이크로폰을 이용한 음원 위치추정 시스템에서 마이크로폰에 수신된 음원의 도착순서를 이용해 음원의 위치를 추정하는 알고리즘을 제안하였다. 제안한 알고리즘을 시뮬레이션 프로그램을 통해 검증한 결과, 음원 추정각도의 오차는 $2^{\circ}{\sim}11.25^{\circ}$로 확인되었으며, 이는 실제각도의 오차범위인 $0^{\circ}{\sim}22.5^{\circ}$ 내에 해당하기 때문에 추정각도의 오차가 최대로 발생하더라도 음원이 발생한 위치를 파악 할 수 있음을 의미한다.

• Journal of Animal Environmental Science
• /
• v.17 no.2
• /
• pp.93-100
• /
• 2011

This study was conducted to verify the applicability of robot milking system through acquisition and analysis of model teat's position information using scanning range finder (SRF). Model teats, same size and shape as real teats, were designed to analyze the properties according to the material, distance error and angle error of the sensor. In addition, 2-dimensional distance information of each teats was obtained at same time with 4 teat models and the result were as follows. 1. In the case of the fingers on the experiment for selection of materials for teat model, the distance error was from 4.3 mm to 1.3 mm, average was 2.8 mm as a minimum record. In the case of rubber material, average distance error was 4.3 mm. So, this material was considered to be a most suitable model. 2. The distance error was maximum at 100 mm distance. The more distance increased, the less error increased up to 300 mm. Then the error increased after 300 mm and decreased again. 3. The maximum angle error of 10.1 mm was measured at $170^{\circ}$, in case of $70^{\circ}$ the error was 0.2 mm as a minimum value. There was no specific tendency to error of angle. 4. In the 2-dimensional location error for 4 teat models, distance error was 3.8 mm as minimum and 7.2 mm as maximum. The angle error was $1.2^{\circ}$ as maximum. All of errors were included within the accuracy of sensor, the robot milking system was considered to be applicable to measure the distance of teats due to the measuring velocity of SRF and the hole size of teat-cup.

• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 1995.10b
• /
• pp.174-179
• /
• 1995

본 논문데서는 부하외란이나 시스템 내부 파라미터의 변동시에 적응력이 저하되는 종래의 PI제어기와, 정상상태 잔류편차가 존재하는 퍼지 제어기의 단점을 극복하기 위한 적 응 퍼지 제어 기법을 제안하였고, 이를 도립 진자 시스템에 적용하였다. 운송차의 위치 및 진자 각도의 오차, 오차의 변화량에 따라 퍼지 추론을 행하여 PI 제어기의 가중치를 결정하 는 구조로, P제어기는 운송차 및 진자의 오차가 과도 상태에서의 영역에서 사용되어 속응성 과 고정도의 특성을 얻는다. 1제어기는 정상상태에서의 정도 향상에 이용되었다. 특히, 제안 하는 적응 퍼지 제어기는 운송차의 위치 오차에 대한 PI 동작과, 진자의 각도 오차에 대한 PI 동작을 각각 퍼지 추론에 의해 부드럽게 전환함으로서 고유 불안정의 시스템인 도립 진 자 시스템의 안정화 제어에 적용하였다.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.17 no.6
• /
• pp.738-743
• /
• 2007

In this paper, a muscle motion sensing system and an artificial arm control system are studied. The artificial arm is for the people who lost one's forearm. The muscle motion sensing system detect the intention of motion from the upper arm's muscle. In sensing system we use flex sensors which is electrical resistance type sensor. The sensor is attached on the biceps brachii muscle and coracobrachialis muscle of the upper arm. We propose an algorithm to classify the one's intention of motions from the sensor signal. Using this algorithm, we extract the 4 motions which are flexion and extension of the forearm, pronation and supination of the arm. To verify the validity of the proposed algorithms we made experiments with two d.o.f. artificial arm. To reduce the control errors of the artificial arm we also proposed a fuzzy PID control algorithm which based on the errors and error rate.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.23 no.2
• /
• pp.96-102
• /
• 2009

In this paper, the effects of the position and the angle of the potential probes on the measurements of the ground resistance with the fall-of-potential method are described and the testing techniques to minimize the measuring errors are proposed. The fall-of-potential method is theoretically based on the potential and current measuring principle and the measuring error is primarily caused by the position and angle of auxiliary probes. In order to analyze the relative error for measuring value of ground resistance due to the position of the potential probe, ground resistance were measured in case that the distance of current probe was fixed at 50[m] and the distance of potential probe was located from l0[m] to 50[m]. Also, the potential probe was located at 30[$^{\circ}$], 45[$^{\circ}$], 60[$^{\circ}$], 90[$^{\circ}$] and 180[$^{\circ}$]. As a consequence, relative error decreased with increasing the distance of potential probe and decreasing the angle between current probe and potential probe. The results could be help to determine the position of potential probe when the ground resistance was measured at grounding system.

• Journal of Digital Convergence
• /
• v.19 no.12
• /
• pp.339-345
• /
• 2021

In this paper, estimation angle performance analysis of amplitude-comparison monopulse radar under additive noise effect is dealt with. When uncorrelated white noises are added to the squinted beams, the angle estimation performance is analyzed through the mean square error(MSE). The numerical integration-based mean square error result completely overlaps the Monte Carlo-based mean square error result, which corresponds to 99.8% of the Monte Carlo-based mean square error result. In addition, the mean square error analysis method based on numerical integration has a much faster operation time than the mean square error method based on Monte Carlo. the angle estimation performance of the amplitude comparison monopulse radar can be efficiently analyzed in various noise environments through the proposed numerical integration-based mean square error method.

• The Journal of Korean Society for Radiation Therapy
• /
• v.29 no.2
• /
• pp.83-91
• /
• 2017

Objectives: The purpose of this study was to evaluate the error of the leaf position accuracy of the MLC due to the gravity effect according to the gantry angle by using picket fence test using EPID and GafChromic EBT3 film. Materials and Methods: A 5 cm solid phantom was placed on the table and the SAD was set to 100 cm. The EBT3 film was placed exactly over the solid phantom and covered a 1.5 cm solid phantom and the picket fence test was performed. The EPID was measured under the same conditions as the EBT3 film at SID 100 cm. The gantry angles were measured at $0^{\circ}$, $90^{\circ}$, $180^{\circ}$ and $270^{\circ}$ in order to evaluate the position of the MLC according to the gantry angle. For the geometric evaluation of the MLC, the leaf position accuracy of the MLC was analyzed using the analysis program. Results: In case of EPID, when the gantry angle was changed to $0^{\circ}$, $90^{\circ}$, $180^{\circ}$, $270^{\circ}$, the difference of the position errors of the leaves was 0.18 mm, 0.31 mm, 0.20 mm, 0.26 mm on the average and the maximum values of the errors were respectively 0.44 mm, 0.54 mm, 0.34 mm, 0.44 mm. In case of EBT3 film, when the gantry angle was changed to $0^{\circ}$, $90^{\circ}$, $180^{\circ}$, $270^{\circ}$, the difference of the position errors of the leaves was 0.19 mm, 0.21 mm, 0.19 mm, 0.31 mm on the average and the maximum values of the errors were respectively 0.35 mm, 0.45 mm, 0.36 mm, 0.48 mm. Conclusion: In this study, we analyzed the position error of the leaf of the MLC according to the gantry angle, and confirmed the position error of the leaf by gravity effect. As a result of comparing the leaf position accuracy using EPID and EBT3 film according to the variation of gantry angle, a larger error occurred in the error analysis method using EPID than that of EBT3 film. Therefore, in the case of IMRT based on MLC, as well as verification of accurate dosimetry should be conducted, it is considered that the quality control and verification for the precise operation of the MLC will be needed. and it is necessary to compare and verify the method of analysis.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.6A
• /
• pp.900-909
• /
• 2000

Adaptive array antennas are one of the most promising techniques for improving the capacity of CDMA mobile communication system. In this paper, the uplink and downlink capacity for asynchronous W-CDMA system with adaptive array antenna is analyzed when an angle estimation error is present. From the results, it is found that the capacities are decreased by the angle estimation error. Specifically, when 5 degrees of error is present at 9 element adaptive array, the capacities are found to decrease by 5.2% in the uplink and 11.6% in the downlink. Also, in this paper, an attempt for comparing the capacities on different channel environments has been made. However, it is found that the increase of the Rice factor hardly effects the capacity due to the power control.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.15 no.5
• /
• pp.361-368
• /
• 2010

This paper presents high speed position controller using stepping motor. The proposed position controller has close loop and open loop mode. In the high speed region, torque angle which is controlled by PI controller and memory based look-up table, is used to keep the reference position. The memory based look-up table produces a torque angle according to motor speed, and the PI controller can compensate the torque angle error. So, the fast dynamic response can be expected in the same position error. The open loop control mode which is divided by 3-modes control the actual position in the low speed and small position error. Each open loop modes are designed to reduce position error and dynamic brake in the stop command. The proposed position control scheme is verified by the practical stepping motor.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.940-944
• /
• 2004

This is a thesis about the Solid Coupling Design and Torsional Angular Error Character. The solid coupling which is designed and made is a strong rigidity material. This is a experiment of Solid Coupling Torsional Error. The Angular Error, FEM and Circularity Measurement. Devices are Twist Friction Driver, Polygon, Autocollimator and Standard Encoder for Measurement. Coupling caused by elastic deformation causes angular error.