• Korean Journal of Food Science and Technology
• /
• v.37 no.1
• /
• pp.11-14
• /
• 2005

White radish was minimally processed, packed with air, $CO_{2}$ (100%), and $CO_{2}/N_{2}$ (25/75%), and irradiated at 0, 1, and 2 kGy, and its microbiological quality and pH were investigated during storage for 2 weeks at $4^{\circ}C$. Irradiation significantly reduced total aerobic, coli-form, and lactic acid bacteria counts. Modified atmosphere packaging (MAP) enhanced microorganism control during storage. Acidity decreased by MAP but was restored during storage, Irradiation did not affect sample pH. Results show irradiation at 2 kGy combined with MAP can enhance microbiological safety and quality of minimally processed radish.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.7 no.2
• /
• pp.116-122
• /
• 2019

This study evaluated the properties of Coal gasification slag(CGS) according to the CGS contents of cement mortar condition as a basic step to examine the applicability of CGS as concrete fine aggregate. Flow increased with increasing CGS contents for both Crushed sand a(CSa) and Crushed sand b+Sea sand(CSb+SS), but the amount of air contents decreased to the opposite tendency. Based on 28 days is maximum compressive strength was obtained at CGS 50% when CSa was used and CGS 75% when CSb+SS. The flexural strength were the maximum at 25% and 50% of CGS, but the tendency was similar to the compressive strength. Compared with CSa, the compressive strength and flexural strength 5% higher than those of CSb+SS, in CGS using of were about 5% higher than those of unused CGS. As a result of comprehensive study on the quality of mortar according to the CGS contents, it can be concluded that when CGS is mixed with fine aggregate at about 50%, it can contribute to securing workability and strength development positively so that resource recycling and quality improvement can be achieved at the same time.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.7 no.3
• /
• pp.194-201
• /
• 2019

This study analyzed the properties of concrete depending on the coal gasification slag(CGS) contents in order to examine the applicability of CGS as the fine aggregate for concrete. Experimental results, trended that the slump and slump flow increased with increasing CGS contents, and air contents has decreased. Evaluation index for segregation of normal strength concrete(EISN) is showed was good from CGS 25% when using crushed sand A(CSa) and CGS 50% when using mixed sand(MS). The compressive strength decreased with increasing CGS contents when CSa was used. However, when MS was used, the maximum value was CGS 50% due to parabolic tendency. Depending on fine aggregates type, compared with compressive strength of CSa was about 8% higher than that of MS, and depending on the use or unuse of CGS, more advantageous at higher strength than low strength. As a result of relative performance study on the quality of concrete according to the CGS contents, it is considered that CGS can be positively contributed to enhancement of workability and strength development when mixed with fine aggregate around 25~50%.

• Nuclear Medicine and Molecular Imaging
• /
• v.40 no.4
• /
• pp.228-232
• /
• 2006

Purpose: electrophilic $^{18}F(T_{1/2}=110\;min)$ radionuclide in the form of $[^{18}F]F_2$ gas is of great significance for labeling radiopharmaceuticals for positron omission tomography (PET). However, its production In high yield and with high specific radioactivity is still a challenge to overcome several problems on targetry. The aim of the present study was to develop a method suitable for the routine production of $[^{18}F]F_2$ for the electrophilic substitution reaction. Materials and Methods: The target was designed water-cooled aluminum target chamber system with a conical bore shape. Production of the elemental fluorine was carried out via the $^{18}O(p,n)^{18}F$ reaction using a two-step irradiation protocol. In the first irradiation, the target filled with highly enriched $^{18}O_2$ was irradiated with protons for $^{18}F$ production, which were adsorbed on the inner surface of target body. In the second irradiation, the mixed gas ($1%[^{19}F]F_2/Ar$) was leaded into the target chamber, fellowing a short irradiation of proton for isotopic exchange between the carrier-fluorine and the radiofluorine absorbed in the target chamber. Optimization of production was performed as the function of irradiation time, the beam current and $^{18}O_2$ loading pressure. Results: Production runs was performed under the following optimum conditions: The 1st irradiation for the nuclear reaction (15.0 bar of 97% enriched $^{18}O_2$, 13.2 MeV protons, 30 ${\mu}A$, 60-90 min irradiation), the recovery of enriched oxygen via cryogenic pumping; The 2nd irradiation for the recovery of absorbed radiofluorine (12.0 bar of 1% $[^{19}F]fluorine/argon$ gas, 13.2 MeV protons, 30 ${\mu}A$, 20-30 min irradiation) the recovery of $[^{18}F]fluorine$ for synthesis. The yield of $[^{18}F]fluorine$ at EOB (end of bombardment) was achieved around $34{\pm}6.0$ GBq (n>10). Conclusion: The production of $^{18}F$ electrophilic agent via $^{18}O(p,n)^{18}F$ reaction was much under investigation. Especially, an aluminum gas target was very advantageous for routine production of $[^{18}F]fluorine$. These results suggest the possibility to use $[^{18}F]F_2$ gas as a electrophilic substitution agent.

• Journal of the Korean Geotechnical Society
• /
• v.32 no.6
• /
• pp.17-26
• /
• 2016

Characteristic behaviors of geo-structure during freezing and thawing process have to be understood based on fundamental knowledge on phase change in porous soil and interaction between soil and structure. Inversion analysis using published one-dimensional soil freezing tests was conducted to suggest a mechanical model to consider an effect of the ice saturation on Young's modulus. Silty soil was more sensitive to temperature than weathered granite soil and sand, and weathered granite soil was more affected by initial water saturation in stiffness decrease than silty soil. Numerical simulations on chilled gas pipeline showed that shielding effect from surrounding frozen zone around the pipe decreases impact from external load onto the pipe. And a pipe installed in sand backfill showed more heaving due to relatively low stiffness of sand during freezing than that of surrounding in-situ weather granite soil. However, it had more stable stress condition due to effective stress redistribution from external load.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.6
• /
• pp.599-605
• /
• 2005

The characteristics of PCDD/Fs were studied when accumulating on 1 to 4 year old pine needles that were used as passive samplers of atmospheric POPs. The rate of concentration increase was linear in lower(tetra- through hexa-) chlorinated PCDD/Fs, but higher (hepta- and octa-) chlorinated homologue concentrations did not increase with needle age. The lower were in gas phase and the higher in particles. Photodegradation rates of PCDDs on pine needles were similar to PCDFs, higher chlorinated PCDD/Fs tend to photolyze quickly. Therefore it is recommended that the younger needles should be collected to avoid errors from the depositional accumulation rates and photodegradation, and that, when comparing local concentrations of PCDD/Fs, needles of same age should be collected to reduce the errors.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.407-407
• /
• 2012

본 연구에서는 p형 전도 특성을 갖는 ZnO 박막 연구를 위해 RF 마그네트론 스퍼터 법으로 Li이 1 at.% 첨가된 ZnO target을 이용하여 ZnLiO 박막을 제작하였다. ZnLiO 박막은 $500{\sim}650^{\circ}C$의 온도 구간에서 $50^{\circ}C$ 단계로 아르곤 가스와 산소의 가스 분압비를 조절하여 성장하였으며, 급속 열처리 법으로 산소분위기에서 3분간 열처리 하였다. 성장된 박막은 전자주사현미경과 x-ray 회절 분광법을 이용하여 구조적 특성을 분석하였고, Hall 효과 측정을 통하여 전기적 특성을 분석하였다. Photoluminescence (PL)법을 통하여 박막의 광학적 특성을 분석하였다. 초기 제작된 ZnLiO 박막은 산소 분위기에서의 급속 열처리과정을 통하여 결정성과 p형 전도 특성이 향상됨을 확인하였다. 이는 열처리 과정을 통해 격자 내 치환되지 못한 Li 원자가 Zn 자리로 치환됨에 따라 격자가 안정화 되며, 억셉터 농도의 증가를 통하여 p-type 전도 특성이 개선된 것으로 보여진다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.11a
• /
• pp.51-59
• /
• 2005

수소 분리막의 적용 분야는 석탄가스, 천연가스, 메탄가스 혼합기체이며, 고온/고압 및 수소농도가 낮은 혼합기체에서 고순도의 수소를 제조하는 곳이다. 특히 치밀질 세라믹 멤브레인은 고온에서 가스화한 석탄가스나 차세대의 쓰레기 처리 기술인 가스화 용융처리에서 생긴 고온가스로부터 고순도의 수소를 분리할 수 있다. 분리한 수소는 고온을 유지하기 때문에 연료전지 발전에 최적이다. 종래의 연료전지는 발전을 위해서 수소의 가열이 필요했으나 이것이 불필요하게 되어 발전 전체의 효율이 향상된다. 석유화학 산업에서 발생하는 혼합기체에서 수소를 분리하여 사용하고 남은 기체는 연료로 재사용할 수 있다. 분리막의 재질로는 고분자계가 개발되고 있으며 고분자 지지체에 백금이나 로듐과 같은 촉매를 코팅하는 방법이다. 이는 기공의 제어가 용이하고 대량생산이 가능한 장점이 있지만 고온에서 사용이 불가능하고 입자상 물질에 의해 분리막의 손상이 문제가 되고 있다. 이에 비해 치밀질 세라믹 멤브레인은 세라믹의 특성에 의해 고온 및 고압에서도 적용이 가능하며, 실온이나 저압의 조건에서도 적용이 가능한 특징을 가진다. $900^{\circ}C$의 고온에서 적용시 세라믹 멤브레인에는 특성열화가 없어 수명이 긴 장점을 가지게 된다. 수소가 포함되어 있는 기체에서 수소 만을 분리하는 방법은 흡착이나 분리막을 이용하는 방법이 일반적이며 흡착에 의한 방법은 일부 실용화가 진행되고 있다. 고효율의 수소를 분리하는 방법으로 분리막을 이용하는 방법이 있다. 현재 치밀질 수소 분리막의 연구는 외국(미국, 일본 등)에서도 초기 연구 단계이다. 국내에서도 이런 연구가 선행되어 외국과의 기술 격차를 줄이고 에너지 자원에 대한 확보가 필요하기 때문에 이 연구가 수행되었다. 치밀질 멤브레인의 소재로는 proton 및 전자전도가 가능한 소재로서 Ba-Ce-Y계를 기본조성으로 하여 내구성과 전기전도도를 향상시키기 위해 Ca, La, In, Yb를 치환하였다. 제조한 재료의 물리화학적 특성을 평가하였고, 수소여과 장치를 이용하여 여과 효율을 평가하였다.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.32 no.5
• /
• pp.695-699
• /
• 2003

Traditional soybean sprouting bucket has some problems which are putrefaction and growing inhibition by the high temperature and carbon dioxide in the bucket during culturing. To solve this problems we developed the new soybean sprouting bucket. The new bucket consisted a square shaped bottom which has 5 draining holes (each 10 mm in dia, 2 mm in height) and four side wall which has two rectangular shaped holes (10 cm long, 0.5 cm wide), and the support vessel which 592 tiny draining holes whose center attached a pipe with 36 small holes (each 2 mm in dia). The new one showed lower temperature and carbon dioxide content during culturing, and the putrefaction was lower, whereas growing degree was higher during culturing at 25$\pm$1$^{\circ}C$ than the traditional bucket.

• Journal of Chest Surgery
• /
• v.40 no.6 s.275
• /
• pp.414-419
• /
• 2007

Background: Replacing the ascending aorta is a standard surgical option for treating acute type A aortic dissection. But replacing the aortic arch has recently been reported as an acceptable procedure for this disease. We compared the effects of aortic arch replacement for treating acute type A aortic dissection with the effects of ascending aortic replacement. Material and Method: From 2002 to 2006, 25 patients undewent surgical treatment for acute type A aortic dissection, 12 patients undewent ascending aortic replacement and 13 patients underwent aortic arch replacement. Among the aortic arch group, an additional distal stent-graft was inserted during the operation in 5 patients. 19 patients (11 arch replaced patients and 8 ascending aortic replaced patients) were followed up at the out patient clinic for an average of $756{\pm}373$ days. All the patients undewent CT scanning and we analyzed their distal aortic segments. Result: 4 patients who underwent ascending aortic replacement died, so the overall mortality rate was 16%. Among the 11 long term followed-up arch replacement patients, 2 patients (18.1 %) developed distal aortic dilatation and one of them underwent thoracoabdominal aortic replacement later on. However, among the 8 the ascending aortic replaced patients, 5 patients (62.5%) developed distal aortic dilatation. Conclusion: Aortic arch replacement is one of the safe options for treating acute type A aortic dissection. Aortic arch replacement for treating acute type A aortic dissection could contribute to a reduced distal aortic dilatation rate and fewer secondary aortic procedures.