• Proceedings of the KIEE Conference
• /
• 1996.07c
• /
• pp.1943-1945
• /
• 1996

In this paper, we developed a modified direct bonding method for the application of vacuum devices. By the proposed method, we successfully bonded the following materials: Si-Si, Si-$SiO_2$-Si, glass-Si, and glass-$SiO_2$-Si. In our experiments, we used corning #7070 wafer type glass and (100) or (110) single crystalline silicon wafers. In order to enhance the initial bonding strength we contacted the materials to be bonded as D. I. water wetted on the surfaces and evaporated the water under the room temperature and atmosphere environment. Finally we realized the glass bonding by simple direct bonding method which has been performed by electrostatic bonding method until now.

• Tribology and Lubricants
• /
• v.8 no.2
• /
• pp.64-72
• /
• 1992

The recent trends of rotating machinery demand high speed and high temperature operation, and the bearing with new material is required to be developed. Ceramic, especially silicon nitride, have been receiving attention as alternative material to conventional bearing steel. Ceramic ball bearing offers major performance advantages over steel bearing, for instance, high speed, maginal lubrication, high temperature, improved corrosion resistance and nonmagnetic capabilities etc.. In this paper, the mechanical characteristics of ceramic ball bearing (hybrid ceramic bearing and all ceramic bearing) were investigated, and the characteristics of ceramic bearing were compared with that of steel bearing. Deep groove ball bearing 6208 was taken the object of analysis. The main results of analysis were followings: the radial stiffness of hybrid and all ceramic bearing were 112% and 130% that of steel bearing, and the axial stiffness of all ceramic bearing was 110% that of steel bearing. According as rotating speed was up, the ball load, the contact angle, the contact stress and the spin-to-roll ratio between ball and raceway of ceramic bearing were far smaller than these of steel bearing. And there was not a significant difference between the minimum film thickness of ceramic bearing and steel bearing. It is expected that this research is contributed to enhanced fundamental technology for the practical applications of ceramic ball bearing.

• Journal of the Korean Society for Heat Treatment
• /
• v.10 no.4
• /
• pp.246-254
• /
• 1997

The 6.5wt %Si-Fe alloy sheets were made by the twin roll process. The magnetic properties and microstructures of sheets annealed in the sulfur atmosphere were studied. In the as-prepared sheet, non-oriented columnar grains about $10{\mu}m$ in diameter were observed, which grew from the surface to the inner part of the sheet. When the annealing temperature was around $700^{\circ}C$, the primary recrystallization was formed around the middle part of the sheet thickness, and the grain size increased with increasing annealing temperature. At the annealing temperature of $900^{\circ}C$, the grain size became $30{\sim}40{\mu}m$. Around the annealing temperature, the motive force of the grain growth is the grain boundary energy. However, above $1000^{\circ}C$ the surface energy played an important role in the observed grain growth. When the sheet were annealed at $1200^{\circ}C$, the grains whose (100) planes were paralled to the thin plate surface grew, and all sheet surfaces were covered with these grains after 1 hour annealing. This phenomenon is called tertiary recrystallization. A difference in surface energy between (100) and (110) surfaces provides a driving force for growth of tertiary grains. The coercive force was 0.27 mOe and the AC core loss $W_{12/50}$ was 0.38w/kg for the 6.5wt%Si-Fe alloy.

• Proceedings of the KIEE Conference
• /
• 2000.11c
• /
• pp.413-415
• /
• 2000

Piezoelectric ceramics of PZT have been developed to apply for transformers in notebook. Use of piezoelectric ceramics in applications like piezoelectric transformers was made possible by the development of new materials with high electromechanical coupling coefficients and high mechanical quality factor. "Hard" ferroelectiric ceramics of complex composition based on lead zirconate titanate with Mn additive have been prepared. The perovskitic phase reaction of the oxides. The crucial role played by the intermediate mixing and grinding procedures in the assessment of the final properties of the material was investigated. Densification up to approximately the theoretical density value was achieved. The polarization was obtained by subjecting the samples at $30kVcm^{-1}$ poling electric field, in a silicon oil bath heated at $110^{\circ}C$. Their microstructural and morphological properties were checked by X-ray diffraction analysis and scanning electron microscopy. The optimized samples presented very high qualify and electromechanical coupling factors, together with small dielectric loss.

• Journal of the Korean Ceramic Society
• /
• v.34 no.10
• /
• pp.1021-1026
• /
• 1997

RuO2 thin film has reasonably good conductivity and stiffness and it is thought to substitute for the cantilever beam made up of Pt and Si3N4 double layers in microactuators. Therefore, anisotopic Si etching was performed using RuO2 thin film as a mask layer in 25 wt. % TMAH water solution. In the etching temperature ranging from 6$0^{\circ}C$ to 75$^{\circ}C$, the etch rates of all the crystallographic directions increased linearly as the etching temperature increased. The etch rate ratio(selectivity) of [111]/[100] which varied from 0.08 to 0.14, was not sensitive to temperature. The activation energies for [110] direction, [100] direction and [111] direction were 0.50, 0.66 and 1.04eV, respectively. RuO2 cantilever beam with a clean surface was formed at the etching temperatures of 6$0^{\circ}C$ and $65^{\circ}C$. But the damages due to formation of pin holes on RuO2 surface were observed beyond 7$0^{\circ}C$. The tensile stress of RuO2 thin films caused the cantilever bending upward. As a result, it was demonstrated that the formation of conducting oxide RuO2 cantilever beam which can replace the role of an electrode and supporting layer could be possible by TMAH solution.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.1
• /
• pp.29-34
• /
• 2009

PLZT thin films were deposited on platinized silicon (Pt/$TiSiO_2$/Si) substrate by RF magnetron sputtering. A $TiO_2$ buffer layer was fabricated, prior to deposition of PLZT films. the layer was strongly affected the crystallographic orientation of the PLZT films. X-ray diffraction was performed on the films to study the crystallization of the films as various substrate temperatures (Ts). According to increasing Ts, preferred orientation of films was changed (110) plane to (111) plane. The ferroelectric, dielectric and electrical properties of the films were also investigated in detail as increased substrate temperatures. The PLZT films deposited at $400^{\circ}C$ showed good ferroelectric properties with the remnant polarization of $15.8{\mu}C/cm^2$ and leakage current of $5.4{\times}10^{-9}\;A/cm^2$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.104-104
• /
• 1999

Cerium dioxide 박막의 포토루미네슨에 관해서는 Cerium 4f band에서 oxygen 2p band로의 transition에 의한 발광(400nm) 현상이 보고되었다. 또한 Indium Oxide 박막의 발광(637nm0 현상이 보고되었다. 본 연구에서는 3족인 Indium을 Si/In/CeO2/Si 구조와 CeO2/Si 구조에 도핑하여 포토루미네슨스 현상을 관찰하였다. E-beam evaporator를 사용하여 Silicon(111) 기판에 Cerium dioxcide 박막을 성장시킨 경우의 두가지 시료를 분석하였다. 포토루미네슨스 관찰을 위해서 Ge-Cd laser (325nm)가 사용되었으며 Indium의 도핑양과 분포 상태를 알기 위해 SIMS와 ADP를 이용하여 분석하였다. Indium양에 대한 포토루미네슨스 변화와 열처리 후의 indium의 분포의 변화에 의한 포토루미네슨스 변화를 관찰하였다. 상온에서 In/CeO2/Si 시료와 Si/In/CeO2/Si 시료에 대한 포토루미네슨스 현상을 관찰한 결과 Si/In/CeO2/Si 시료에서만 500nm(2.5eV)에서 발광 현상이 관찰되었다. 도핑된 indium은 ADP에서는 검출되지 않고 SIMS에서만 검출되어 ADP의 detection range(1-0.1%) 이하의 양이 도핑된 것으로 추측된다. 도핑된 Indium의 양이 증가할수록 포토루미네슨스의 Intensity가 증가하였다. 또한 열처리(110$0^{\circ}C$, 1min) 후 포토루미네슨스의 peak위치가 390nm(3.18eV)로 변화하였다. Si/In/CeO2/Si에서 포토루미네슨스 현상이 관측되고 Intensity가 indium의 양에 의존하므로 완전하지 못한 Cerium dioxide의 CeOx 구조와 indium과의 결합이 포토루미네슨스의 원인으로 추측된다. 열처리 후 SIMS의 분석결과 indium의 분포가 변화하였으며 이는 포토루미네슨스의 변화의 원인으로 판단된다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.110-111
• /
• 2006

이중 에피층을 가지는 SOI (Silicon-On-Insulator) RESURF(REduced SURface Field) LIGBT(Lateral Insulated Gate Bipolar Transistor) 소자의 에피층 두께에 따른 항복전압 특성을 분석하였다. 이중 에 피층 구조를 가지는 SOI RESURF LIGBT 소자는 전하보상효과를 얻기 위해 기존 LIGBT 소자의 n 에피로 된 영역을 n/p 에피층의 이중 구조로 변경한 소자로 n/p 에피층 영역내의 전하간 상호작용에 의해 에피 영역 전체가 공핍됨으로써 높은 에피 영역농도에서도 높은 항복전압을 얻을 수 있는 소자이다. 본 논문에서는 LIGBT 에피층의 전체 두께와 농도를 고정한 상태에서 n/p 에피층의 두께가 변하는 경우에 항복전압 특성의 변화에 대해 simulation을 통해 분석하였다.

• Korean Journal of Materials Research
• /
• v.34 no.2
• /
• pp.105-110
• /
• 2024

Scanning probe microscopy (SPM) has become an indispensable tool in efforts to develop the next generation of nanoelectronic devices, given its achievable nanometer spatial resolution and highly versatile ability to measure a variety of properties. Recently a new scanning probe microscope was developed to overcome the tip degradation problem of the classic SPM. The main advantage of this new method, called Reverse tip sample (RTS) SPM, is that a single tip can be replaced by a chip containing hundreds to thousands of tips. Generally for use in RTS SPM, pyramid-shaped diamond tips are made by molding on a silicon substrate. Combining RTS SPM with Scanning spreading resistance microscopy (SSRM) using the diamond tip offers the potential to perform 3D profiling of semiconductor materials. However, damage frequently occurs to the completed tips because of the complex manufacturing process. In this work, we design, fabricate, and evaluate an RTS tip chip prototype to simplify the complex manufacturing process, prevent tip damage, and shorten manufacturing time.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2008.05a
• /
• pp.105-110
• /
• 2008

We have proposed a new structure of poly-silicon thin film transistor(TFT) which was fabricated the LDD region using doping oxide with graded spacer by etching shape retio. The devices of n-channel poly-si TFT's hydrogenated by $H_2$ and $HT_2$/plasma processes are fabricated for the devices reliability. We have biased the devices under the gate voltage stress conditions of maximum leakage current. The parametric characteristics caused by gate voltage stress conditions in hydrogenated devices are investigated by measuring /analyzing the drain current, leakage current, threshold voltage($V_{th}$), sub-threshold slope(S) and transconductance($G_m$) values. As a analyzed results of characteristics parameters, the degradation characteristics in hydrogenated n-channel polysilicon TFT's are mainly caused by the enhancement of dangling bonds at the poly-Si/$SiO_2$ interface and the poly-Si Brain boundary due to dissolution of Si-H bonds. The structure of novel proposed poly-Si TFT's are the simplity of the fabrication process steps and the decrease of leakage current by reduced lateral electric field near the drain region.