• Korean Chemical Engineering Research
• /
• v.54 no.2
• /
• pp.152-156
• /
• 2016

Experimental research on the preparation of photocatalyst for the decomposition of brilliant blue FCF ($C_{37}H_{31}O_9N_2S_3Na_2$) was performed. $TiO_2$ and ZnO powders were prepared from titanium (IV) sulfate and zinc acetate at low reaction temperature and atmospheric pressure by hydrothermal precipitation method without calcination. In addition, $TiO_2$ was prepared with cationic surfactant CTAB (Hexadecyltrimethyl ammonium bromide) at the same conditions. The physical properties of prepared $TiO_2$ and ZnO, such as crystallinity, average particle size and absorbance, were investigated by XRD, Zeta-potential meter and DRS. And, the photocatalytic degradation of brilliant blue FCF has been studied in the batch reactor under UV radiation. For the photocatalysts prepared without CTAB, $TiO_2$ has smaller particle size and larger absorbance and photocatalytic reaction rate than ZnO. And $TiO_2$, prepared with CTAB whose concentration is 1/10 of that of precursor, shows 15% higher than that prepared without CTAB in final photocatalytic degradation ratio of brilliant blue FCF.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1989.06a
• /
• pp.70-73
• /
• 1989

(1-x-y)Pb($Zn_{1/3}Nb_{2/3})O_3-Ba(Zn_{1/3}Nb_{2/3})O_3-PbTiO_3(0.12{\leq}x{\leq}0.21, 0.24{\leq}y{\leq}0.33$) ternary compound ceramics were fabricated by the mixed oxide method. The sintering temperature and time were 1050 [$^{\circ}C$], 2[hr]. Morphotropic phase boundary region was chosen for the composition. 0.55 PZN-0.21 BZN-0.24 PT specimen had the highest value of relative dielectric constants, 5353. The curie temperature of specimens were increased linearly with PT content. Near the morphotropic phase boundary, electro-mechanical coupoling factor and mechanical quality factor of the specimens had the highest values.

• Journal of the Korean Ceramic Society
• /
• v.21 no.2
• /
• pp.121-126
• /
• 1984

The dielectric properties of $BaTiO_3$ containing 0~0.3mol% and ZnO respectively as additives were investigated as a function of temperature from $25^{\circ}C$ to 14$0^{\circ}C$ and frequency from 24 KHz to 15MHz. The density of sintered $BaTiO_3$ was increased with addition of increasing to 0.15mol% amounts of $Sb_2O_3$ and the dielectric constant was also increased. This is due to space charge polarization with Ba vacancies. Above 0.15mol% $Sb_2O_3$ the density was decreased and the dielectric constant was also decreased due to occuring the discharge through voids. The density of sintered $BaTiO_3$ was decreased with addition of increasing to 0.15mol% amounts of ZnO and the dielectric constant was decreased due to occuring the discharge through voids. Above 0.15mol% ZnO the density was increased and the dielectric constant was also increased.

• Transactions on Electrical and Electronic Materials
• /
• v.14 no.6
• /
• pp.312-316
• /
• 2013

In this study, short-circuit preventive layer (blocking layer) was deposited between conductive transparent electrode and porous $TiO_2$ film in the DSSCs. As blocking layer, we selected the metal-oxide such as $TiO_2$, $Nb_2O_5$ and ZnO. The sheet resistance with each different blocking layers were 18 ${\Omega}/sq.$ for the $TiO_2$, 10 ${\Omega}/sq.$ for the $Nb_2O_5$ and 8 ${\Omega}/sq.$ for the ZnO, while the RMS (Root Mean Square) roughness value of DSSCs were 39.61 nm for the $TiO_2$, 41.84 nm for the $Nb_2O_5$ and 36.14 nm for the ZnO respectively. From the results of photocurrent-voltage curves, a sputtered $Nb_2O_5$ blocking layer showed higher performance on 2.64% of photo-electrochemical properties. The maximum of conversion efficiency which was achieved under 1 sun irradiation by depositing the blocking layer increased up to 0.56%.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.682-683
• /
• 2006

Thermoelectric conversion efficiency of thermoelectric elements can be increased by using a structure combining n-type and p-type semiconductors. From the above point of view, attention was directed at ZnO as a candidate n-type semiconductor material and investigations were made. As the result, a dimensionless figure of merit ZT close to 0.28 (1073K) was obtained for specimens produced by the PCS (Pulse Current Sintering) method with addition of specified quantities of $TiO_2$, CoO, and $Al_2O_3$ to ZnO. It was found that the interstitial $TiO_2$ in the ZnO restrains the grain growth and CoO acts onto the bond between grains. The influence of the inclusion of $TiO_2$ and CoO onto the sintering behavior also was investigated.

• Journal of the Korean Ceramic Society
• /
• v.42 no.4
• /
• pp.276-281
• /
• 2005

$LiNi_{1-y}M_{y}O_{2}(M=Zn^{2+},\;Al^{3+},\;and\;Ti^{4+},\;0.000\{\le}y{\le}0.100)$ were synthesized by the combustion method by calcining in $O_{2}$ stream at $750^{\circ}C$ for 36 h. XRD analyses, observation by FE-SEM and measurement of the variation of discharge capacity with the number of cycles were carried out. The composition $LiNi_{0.99}M_{0.01}O_{2}(M=Zn^{2+},\;Al^{3+},\;and\;Ti^{4+})$ of all the compositions showed relatively good electrochemical properties. $LiNi_{0.99}M_{0.01}O_{2}$ exhibited poor crystallinity and $LiNi_{0.99}M_{0.01}O_{2}$ showed the cation mixing of large fraction. $LiNi_{0.99}M_{0.01}O_{2}$ with improved cycling performance showed good crystallinity and the cation mixing of small fraction.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.8
• /
• pp.1211-1216
• /
• 1989

To enhance the breakdown properties of low voltage-oriented ZnO varistor, sample were fabricated with additive oxides and sintering conditions. Addition of TiO2 lowered breakdown voltage` nonlinear resistances were lowered about 10V/mm and nonlinear exponents were not lowered with respect to it with the basic composition. To the samples added TiO2, V2ko5, and Cr2O3, microstructures were observed by SEM, moreover Ti was detected at grainboundaries and within the grain by EDS. Addition of Si-oxides and Sb2O3 increased nonlinear exponent and also increased nonlinear resistance, by addition of TiO2 to these samples at the sintering conditions of 1250\ulcorner and 1 hour we could fabricate low voltage-oriented ZnO varistors with nonlinear exponent of 30 or more and with real breakdown voltage of 30V/mm.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1988.10a
• /
• pp.8-11
• /
• 1988

(1-x-y)Pb($Zn_{1/3}Nb_{2/3})0_3-BaTiO_3PbTiO_3(0.05{\leq}x{\leq}0.20, 0.05{\leq}y{\leq}0.15$) ternary compound ceramics were fabricated by the mixed oxide method. The dielectric properties with temperature and frequency of the specimens were investigated. Relative dielectric constants of the specimens were increased with $BaTiO_3$ contents. Increasing the $BaTiO_3$contents, the variation in the relative dielectric constant with frequency, the temperature coefficient of capacitance (TCC) and the dielectric loss were decreased.

• Journal of the Korean Ceramic Society
• /
• v.30 no.11
• /
• pp.925-932
• /
• 1993

The perovskite phase in PZN-PMN-PT (Pb(Zn, Mg)1/3Nb2/3O3-PbTiO3) pseudoternary ceramics was stabilized by the addition of excess constituent divalent oxides (PbO, MgO and ZnO). The excess addition of 5mol% MgO or 7.5mol% PbO fully stabilized the perovskite phase. The enhanced diffuse phase transition (DPT) and the decrease in the electrical resistivity observed in the presence of excess ZnO or MgO were interpreted in terms of the additional formation of negatively charged, short-range ordered 1:1 domains with a concomitant generation of charge carriers, holes.

• Journal of the Korean Ceramic Society
• /
• v.39 no.5
• /
• pp.438-445
• /
• 2002

In this study, the glass frit of $PbO-TiO-2-SiO_2-BaO-ZnO-Al_2O-3-CaO-B_2O_3-Bi_2O_3-MgO$ system was manufactured. The glass was melted at $1,400{\circ}C$, quenched and attrition-milled. The glass frit powder was pressed and fired for 2h at the range of $750~1,000{\circ}C$. The crystallization of glass frit began at about $750{\circ}$ and at low temperature, the main crystal phases were hexagonal celsian($BaAl_2Si_2O_8$) and alumina. As the firing temperature increased, the crystal phases of monoclinic celsian, zinc aluminate, zinc silicate, calcium titanium silicate and titania appeared. And the increase of firing temperature led to transformation of hexagonal celsian to monoclinic. The only glass frit containing 15wt% PbO had the crystal phase of solid solution of $PbTiO_3-CaTiO_3$. At the frequency of 1 MHz, the dielectric constant of glass frit crystallized was in the range of 11~16 and the dielectric loss less than 0.020. But the glass frit containing 15wt% PbO had the dielectric constant of 17~26 and loss of 0.010~0.015 because of crystal phase of solid solution of $PbTiO_3-CaTiO_3$.