• Journal of the Korean Ceramic Society
• /
• v.52 no.5
• /
• pp.380-383
• /
• 2015

We prepared the $TiO_2$ layer with 0 ~ 4 wt% of polystyrene (PS) beads having a radius of 250 nm to increase the dye adsorption and energy conversion efficiency (ECE) of a dye sensitized solar cell (DSSC). Then, we fabricated DSSCs using $0.45cm^2$ active area. FE-SEM was used to characterize the microstructure consisting of $TiO_2$ layer and PS beads. UV-VIS-NIR was used to determine the optical absorbance of working electrodes (WEs). Solar simulator and potentiostat were used to determine the photovoltaic properties. We observed that pores having a radius of 250 nm were formed with the density of $0.15ea/{\mu}m^2$ in $TiO_2$ layers after conducting the sintering process. The absorbance in visible light regime was found to increase with the increase in the amount of PS beads. The ECE increased from 4.66% to 5.25% when the amount of PS beads was increased from 0 to 4 wt%. This is because the pores of PS beads increased the adsorption of dye. Our results indicate that the ECE of the DSSCs can be enhanced by the addition of an appropriate amount of PS beads into $TiO_2$ layers.

• Applied Chemistry for Engineering
• /
• v.7 no.4
• /
• pp.794-801
• /
• 1996

$TiO_2$ fine powders were synthesized via hydrolysis reaction of titanium isopropoxide in isopropanol solvent and the reaction rates were studied by use of UV spectroscopic method. The reactions were controlled to proceed to pseudo-first-order reaction in the presence of excess water in isopropanol solvent. The rate constants which varied with temperature and concentration of water were calculated by Guggenheim method. Reactions using $D_2O$ were also carried out to determine the catalytic character of water. n value of water molecules in transition state and the thermodynamic parameters showed that the reaction proceeded by $S_N2$ mechanism. $TiO_2$ powders synthesized in this reaction were almost spheric forms and had average particle size of $0.3{\mu}m$ diameter.

• Applied Chemistry for Engineering
• /
• v.31 no.1
• /
• pp.43-48
• /
• 2020

Fe₂O₃ nanoparticles with the mixed structure of cubic and nanorod were synthesized by precipitation, hydrothermal, sol-gel method, etching process and heat treatment. Fe₂O₃/TiO₂ core-shell (CS) of type Fe₂O₃@TiO₂ composite was fabricated on a 20 nm nanolayer of TiO₂ coated on the surface of Fe₂O₃ nanoparticles. Fe₂O₃/TiO₂ yolk-shell (YS) composite was prepared by chemical etching and heat treatment of Fe₂O₃/TiO₂ CS nanoparticles. Physical properties of Fe₂O₃, Fe₂O₃@TiO₂ CS and Fe₂O₃@TiO₂ YS nanoparticles were characterized by FE-SEM, HR-TEM and X-ray diffraction. The solar reflectance, commission internationale de l'Elcairage (CIE) color coordinate and heat shield temperatures of Fe₂O₃, CS and YS type Fe₂O₃@TiO₂ pigments filled with poly acrylate (PA) paints were investigated by UV-Vis-NIR spectrometer and homemade heat shield temperature measuring device. The Fe₂O₃@TiO₂ YS red pigment filled PA composite exhibited excellent near infrared light reflecting performance and also reduced the heat shield temperature of 13 ℃ than that of Fe₂O₃ filled counterparts.

• Bulletin of the Korean Chemical Society
• /
• v.28 no.6
• /
• pp.1015-1020
• /
• 2007

A simple approach to prepare arrays of Au/TiO2 composite nanoparticles by using Au-loaded block copolymers as templates combined with a sol-gel process is described. The organic-inorganic hybrid films with closely packed inorganic nanodomains in organic matrix are produced by spin coating the mixtures of polystyrene-block-poly(ethylene oxide) (PS-b-PEO)/HAuCl4 solution and sol-gel precursor solution. After removal of the organic matrix with deep UV irradiation, arrays of Au/TiO2 composite nanoparticles with different compositions or particle sizes can be easily produced. Different photoluminescence (PL) emission spectra from an organic-inorganic hybrid film and arrays of Au/TiO2 composite nanoparticles indicate that TiO2 and Au components exist as separate state in the initial hybrid film and form composite nanoparticles after the removal of the block copolymer matrix.

• Journal of the Microelectronics and Packaging Society
• /
• v.27 no.1
• /
• pp.25-29
• /
• 2020

This study demonstrates direct-patternable amorphous TiO_x resistive switching (RS) device and the fabrication method using photochemical metal-organic deposition (PMOD). For making photosensitive stock solutions, Ti(IV) 2-ethylhexanoate was used as starting precursor. Photochemical reaction by UV exposure was observed and analyzed by Fourier transform infrared spectroscopy and the reaction was completed within 10 minutes. Uniformly formed 20 nm thick amorphous TiO_x film was confirmed by atomic force microscopy. Amorphous TiO_x RS device, formed as 6 × 6 ㎛ square on 4 ㎛ width electrode, showed forming-less RS behavior in ±4 V and on/off ratio ≈ 20 at 0.1 V. This result shows PMOD process could be applied for low temperature processed ReRAM device and/or low cost, flexible memory device.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.11
• /
• pp.3301-3306
• /
• 2013

This paper aims to address the cellular toxicity of ultra-pure titanium dioxide ($TiO_2$) and zinc oxide (ZnO) nanoparticles (NPs) frequently employed in sunscreens as inorganic physical sun blockers to provide protection against adverse effects of ultraviolet (UV) radiation including UVB (290-320 nm) and UVA (320-400 nm). In consideration that the production and the use of inorganic NPs have aroused many concerns and controversies regarding their safety and toxicity and that microsized $TiO_2$ and ZnO have been increasingly replaced by $TiO_2$ and ZnO NPs (< 100 nm), it is very important to directly investigate a main problem related to the intrinsic/inherent toxicity of these NPs and/or their incompatibility with biological objects. In the present study, we took advantage of the laser-assisted method called laser ablation for generation of $TiO_2$ and ZnO NPs. NPs were prepared through a physical process of irradiating solid targets in liquid phase, enabling verification of the toxicity of ultra-pure NPs with nascent surfaces free from any contamination. Our results show that $TiO_2$ NPs are essentially non-poisonous and ZnO NPs are more toxic than $TiO_2$ NPs based on the cell viability assays.

• Journal of the Mineralogical Society of Korea
• /
• v.28 no.3
• /
• pp.245-253
• /
• 2015

The performance of $TiO_2$ photo-catalytic oxidation process is significantly dependent on the amount of hydroxyl radicals produced during the process, and it is an essential prerequisite to quantify its production. However, precise and accurate methods for quantification of hydroxyl radicals have not been developed so far. For this reason, this study was initiated to compare existing methods for analysis of hydroxyl radicals produced by $TiO_2$ photo-catalytic oxidation and to propose a new method to overcome the limitation of established methods. To simulate $TiO_2$ photo-catalytic oxidation process, Degussa P25 which has been widely used as a standard $TiO_2$ photo-catalyst was used with the dose of 0.05 g/L. The light source of process was UVC mercury low-pressure lamp (11 W, $2,975mW/cm^2$). The results indicate that both potassium iodide (KI)/UV-vis spectrometer and terephthalic acid (TPA)/fluorescence spectrometer methods could be applied to qualitatively measure hydroxyl radicals via detection of triiodide ion ($I_3{^-}$) and 2-hydroxyterephthalic acid which are produced by reactions of iodine ion ($I^-$) and TPA with hydroxyl radicals, respectively. However, it was possible to quantitatively measure hydroxyl radicals using TPA method coupled with high-performance liquid chromatograph (HPLC). The analytical results using TPA/HPLC method show that hydroxyl radical of 0.013 M was produced after 8 hours operation of photo-catalytic oxidation under specific experimental conditions of this study. The proposed method is expected to contribute to precise the evaluation of the performance of photo-catalytic oxidation process.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.68.2-68.2
• /
• 2010

Dye-sensitized solar cells (DSSC) show great promise as an inexpensive alternative to conventional p-n junction solar cells. Investigations into the various factors influencing the photovoltaic efficiency have recently been intensified. The conventional absorber electrode in DSSC is composed of compacted or sintered $TiO_2$ nanopowder that carries an anchored organic dye. The absorbance of incident light in the DSC is realized by specifically engineered dye molecules placed on the semiconductor electrode surface ($TiO_2$). The dye absorbs light at wavelengths up to about 920nm, the energy of the exited state of the molecule should be about 1.35eV above the electronic ground state corresponding to the ideal band gap of a single band gap solar cell. The dye molecules ar adhered onto the nanostrutured $TiO_2$ electrode by immersing the sintered electrode into a dye solution, typically 3mM in alcohol, for a long enough period to fully impregnate the electrode. However, the concentrations of the dye is slightly changed due to the evaporation of the alcohol. The dye is more expensive than other materials in DSSC and related to the efficiency of DSSC. Therefore, the concentrations of the dye should be carefully measured. In this study, we investigated to the dye loading on fired $TiO_2$ powder as a function of temperature by the TG-DTA and the dye solution by UV-visible spectroscopy after the impregnation process. The dye loading is related to the porosity of the nanostructured $TiO_2$ electrode.

• Journal of Environmental Science International
• /
• v.17 no.11
• /
• pp.1195-1201
• /
• 2008

Enhancing with non-metallic elemental nitrogen(N) is one of several methods that have been proposed to modify the electronic properties of bulk titanium dioxide($TiO_2$), in order to make $TiO_2$ effective under visible-light irradiation. Accordingly, current study evaluated the feasibility of applying visible-light-induced $TiO_2$ enhanced with N element to cleanse aromatic compounds, focusing on xylene isomers at indoor air quality(IAQ) levels. The N-enhanced $TiO_2$ was prepared by applying two popular processes, and they were coated by applying two well-known methods. For three o-, m-, and p-xylene, the two coating methods exhibited different photocatalytic oxidation(PCO) efficiencies. Similarly, the two N-doping processes showed different PCO efficiencies. For all three stream flow rates(SFRs), the degradation efficiencies were similar between o-xylene and m,p-xylene. The degradation efficiencies of all target compounds increased as the SFR decreased. The degradation efficiencies determined via a PCO system with N-enhanced visible-light induced $TiO_2$ was somewhat lower than that with ultraviolet(UV)-light induced unmodified $TiO_2$, which was reported by previous studies. Nevertheless, it is noteworthy that PCO efficiencies increased up to 94% for o-xylene and 97% for the m,p-xylene under lower SFR(0.5 L $min^{-1}$). Consequently, it is suggested that with appropriate SFR conditions, the visible-light-assisted photocatalytic systems could also become important tools for improving IAQ.

• Membrane Journal
• /
• v.20 no.1
• /
• pp.1-7
• /
• 2010

A graft copolymer, i.e. poly(vinylidene fluoride-co-chlorotrifluoroethylene )-g-poly(styrene sulfonic acid) (P(VDF-co-CTFE)-g-PSSA) with 47 wt% of PSSA was synthesized via atom transfer radical polymerization (ATRP). This copolymer was combined with titanium isopropoxide (TTIP) to produce graft copolymer/$TiO_2$ nanocomposite membranes via sol-gel process. $TiO_2$ precursor (TTIP) was selectively incorporated into the hydrophilic PSSA domains of the graft copolymer and grown to form $TiO_2$ nanoparticles, as confirmed by FT-IR and UV-visible spectroscopy. Water uptake and ion exchange capacity (IEC) decreased with TTIP contents due to the decrease in number of sulfonic acid in the membranes. At 5 wt% of TTIP, the mechanical properties of membranes increased while maintaining the proton conductivity.