• Nuclear Engineering and Technology
• /
• v.52 no.7
• /
• pp.1503-1510
• /
• 2020

Ultra-low noise charge sensitive amplifiers (CSAs) based on various types of circuit board substrates, such as FR4, Teflon, and ceramics (Al₂O₃) with two different designs, PA1 and PA2, have been developed. They were tested to see the noise effect from the dielectric loss of the substrate capacitance before and after irradiation. If the electronic noise from the CSAs is to be minimized and the energy resolution enhanced, the shaping time has to be optimized for the detector, and a small feedback capacitance of the CSA is favorable for a better SNR. Teflon- and ceramic-based PA1 design CSAs showed better noise performance than the FR4-based one, but the Teflon-based PA1 design showed better sensitivity than ceramic based one at a low detector capacitance (<10 pF). In the PA2 design, the equivalent noise and the sensitivity were 0.52 keV FWHM for a silicon detector and 7.2 mV/fC, respectively, with 2 ㎲ peaking time and 0.1 pF detector capacitance. After 10, 100, 10³, 10⁴, and 10⁵ Gy irradiation the ENC and sensitivity characteristics of the developed CSAs based on three different substrate materials are also discussed.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.32 no.2
• /
• pp.58-67
• /
• 2000

This study was carried out to acquire basic data necessary for the use of non-wood pulp. Various chemical pulping methods for rice straw to achieve higher yield, lower Kappa No. were investigated and then the physical properties of various pulps were tested. The results of this study were as follows: When various chemical pulps (Soda, Soda-AQ, Soda-$H_2O_2$, Soda-$Na_2S_2$, AS, AS-AQ, AS-$Na_2S_2O_3$, AS-$Na_2S_2O_4$, Kraft) were produced with rice-straw, the pulps with the highest yield and lowest Kappa No. were obtained with Soda-$Na_2S_2$and AS-$Na_2S_2O_4$pulps. For the breaking length, Soda and Soda-additive pulps(7.5~9.2km) were better than AS and AS-additive pulps(6.2~8.1km). Similarly, for the burst index, Soda and Soda-additive pulps(6.0~7.0 kPa.$m^2$/g) were better than AS and AS-additive pulps(4.5~6.3 kPa.m$^2$/g). But the tear index was showed 21.8-30.9 mN.$m^2$/g with a little different between pulping methods.

• Applied Chemistry for Engineering
• /
• v.8 no.5
• /
• pp.749-755
• /
• 1997

Molybdenum phosphate(P/Mo = 0.6) has been synthesized with ammonium molybdate and phosphoric acid under aqueous solution. The kinetics of the ammoxidation of methylpyrazine over molybdenum phosphate catalyst was investigated with the variation of reaction temperature and partial pressure of methylpyrazine, oxygen and ammonia, respectively at atmospheric pressure. The catalytic activity was constant for 300hrs operation under our experimental conditions. Under the steady-state condition, the rate equation of methylpyrazine was shown as $-r=kP_{MP}P_{NH3}{^0}P_{O2}{^{\gamma}}({\gamma}=2.2;1.3{\leq}P_{O2}(kPa){\leq}4)$. The apparent activation energy was 29.6kcal/mol below 623K. The main product obtained in the ammoxidation of methylpyrazine is cyanopyrazine whose selectively was kept always over 90% regardless of conversion.

• Journal of Sensor Science and Technology
• /
• v.16 no.2
• /
• pp.126-131
• /
• 2007

In this paper, we fabricated piezoresistive pressure sensor with dry etching technology which used ICP-RIE (inductively coupled plasma reactive ion etching) and etching delay technology which used SOI (silicon-on-insulator). Structure of the fabricated pressure sensor shows a square diaphragm connected to a frame which was vertically fabricated by dry etching process and a single-element four-terminal gauge arranged at diaphragm edge. Sensitivity of the fabricated sensor was about 3.5 mV/V kPa at 1 kPa full-scale. Measurable resolution of the sensor was not exceeding 20 Pa. The nonlinearity of the fabricated pressure sensor was less than 0.5 %F.S.O. at 1 kPa full-scale.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.23 no.4
• /
• pp.167-172
• /
• 2013

Titanium dioxides nanoparticles coated aluminum oxide powders were fabricated by pulsed laser deposition (PLD) with Nd : YAG laser at 266 nm. The Pulse laser energy is 100 mJ/pulse. During the irradiation of the focused laser on the $TiO_2$ target, Ar gas is supplied into the chamber. The gas pressure is varied in a range of $1{\times}10^{-2}$ to 100 Pa. Titanium dioxides nanoparticles deposited aluminum oxide powders were characterized by using energy dispersive X-ray spectroscopy (EDX), high resolution transmission electron microscopy (HR-TEM), in order to understand the effect of Ar background gas on surface morphology and properties of the powders. The coated $TiO_2$ nanoparticles had nanosized spherical shape and the crystallite sizes of 10~30 nm. The morphology of coated $TiO_2$ nanoparticles is not affected by gas pressure. However, the particle size and crystallinity slightly increased with the increase of gas pressure. According to this technique, the size and crystallinity of nanoparticles can be easily controlled by controlling pressure during the laser irradiation.

• Analytical Science and Technology
• /
• v.15 no.3
• /
• pp.256-262
• /
• 2002

After porous filters were manufactured using cordierite powder whose mean paricle size was 200${\mu}m$, they were loaded with catalysts such as $V_2O_5$, CuO and $LaCoO_3$ by vacuum impregnation method. And the NOx/SOx simultaneous removal efficiency was measured by passing NO and $SO_2$ through catalyst-loaded ceramic filters. The cordierite porous filters had the apparent porosity of 61.6%, the compressive strength of 12.3 MPa and the pressure drop of 147 pa at the face velocity of 5 cm/sec. According to the analysis of NO/$SO_2$ simultaneous removal efficiency, perovskite $LaCoO_3$ catalyst was the most efficient for the simultaneous NO and $SO_2$ removal. The $LaCoO_3$ catalyst-loaded filter could remove more than 90% for NO and more than 80% for $SO_2$.

• Tuberculosis and Respiratory Diseases
• /
• v.43 no.6
• /
• pp.987-996
• /
• 1996

Background : We prospectively evaluated the applicability and effect of noninvasive ventilation (NIV) in acute respiratory failure and tried to find out the parameters that could predict successful application of NIV. Methods : Twenty-six out of 106 patients with either acute ventilatory failure (VF: $PaCO_2$ > 43 mm Hg with pH < 7.35) or oxygenation failure (OF: $PaO_2/AO_2$ < 300 mm Hg with $pH{\geq}7.35$) requiring mechanical ventilation were managed by NIV (CPAP + pressure suppon, or BiPAP) with face mask. Eleven out of 19 cases with VF (57.9%) (M : F=7 : $55.4{\pm}14.6$ yrs) and 15 out of 87 cases with OF (17.2%) (M : F=12 : 3, $50.6{\pm}15.6$ yrs) were s uilable for NIY. Respiratory rates, arterial blood gases and success rate of NIV were analyzed in each group. Results: 81.8% (9/11) of YF and 40% (6/15) of OF were successfully managed on NIV and were weruled from mechanical ventilator without resorting to endotracheal intubation. Complications were noted in 2 cases (nasal skin necrosis 1, gaseous gastric distension 1). In NIV for ventilatory failure, the respiration rate was significantly decreased at 12 hour of NIV ($34{\pm}9$ /min pre-NIV, $26{\pm}6$ /min at 12 hour of NIV, p=0.045), while $PaCO_2$ ($87.3{\pm}20.6$ mm Hg pre-NIV, $81.2{\pm}9.1$ mm Hg at 24 hour of NIV) and pH ($7.26{\pm}0.04$, $7.32{\pm}0.02$, respectively, p <0.05) were both significantly decreased at 24 hour of NIV In NIV for oxygenation failure, $PaCO_2$ were not different between the successful and the failed cases at pre-NIV and till 12 hours after NIV. The $PaO_2/FIO_2$ ratio, however, significantly improved at 0.5 hour of NIV in successful cases and were maintained at around 200 mm Hg (n=6 : at baseline, 0.5h, 6h, 12h : $120.0{\pm}19.6$, $218.9{\pm}98.3$, $191.3{\pm}55.2$, $232.8{\pm}17.6$ mm Hg, respectively, p=0.0211), but it did not rise in the failed cases (n=9 : $127.9{\pm}63.0$, $116.8{\pm}24.4$, $100.6{\pm}34.6$, $129.8{\pm}50.3$ mm Hg, respectively, p=0.5319). Conclusion : From the above results we conclude that NIV is effective for hypercapnic respiratory failure and its success was heralded by reduction of respiration rale before the reduction in $PaCO_2$ level. In hypoxic respiratory failure, NIV is much less effective, and the immediate improvement of $PaO_2/FIO_2$ ratio at 0.5h after application is thought to be a predictor of successful NIV.

• Journal of the Korean Ceramic Society
• /
• v.39 no.6
• /
• pp.610-615
• /
• 2002

Phase formation and proton conduction of L $a_{0.6}$B $a_{0.4}$I $n_{1-y}$ $M_{y}$ $O_{3-{\delta}}$(M=G $a^{3+}$, S $c^{3+}$, Y $b^{3+}$) system were studied. A cubic perovskite structure with a single phase was formed in all of the compositions of this work except for the composition off=G $a^{3+}$ with y=0.5, viz,L $a_{0.6}$B $a_{0.4}$I $n_{1-y}$G $a_{0.5}$ $O_{3-{\delta}}$ For the compositions of M=S $c^{3+}$and Y $b^{3+}$with y=0.25, proton conduction occurred in wet $N_2$ atmosphere(P $h_{H_2O}$=6.1hPa).X>/=6.1hPa).Pa).

• Journal of the Korean Ceramic Society
• /
• v.56 no.6
• /
• pp.566-576
• /
• 2019

In this work, we investigated kaolinite raw materials from China, Vietnam, and Seongju (Korea) used for the manufacture of porcelain products in Korea. According to chemical analysis results, for the kaolinites from Seongju, more feldspar components containing CaO, K₂O, and Na₂O are found than in those from China or Vietnam, of which the composition is close to that of pure kaolinite. Through X-ray Rietveld quantitative analysis, kaolinite and muscovite are found to be the main phases for all the raw materials. Halloysite, quartz, gibbsite, and andesine are found at more than 5% for KM-85 (China), LKC-60 (Vietnam), KC-009 (China), and WA (Seongju). Absorption rate is on order of LKC-60 < KC-009 < KM-85 < PA < WA, and the sample, sintered in reductive atmosphere, exhibits the lowest absorption rate. Comparing the color of the sintered samples, kaolinites of KM-85, LKC-60, and KC-009 (L^*: 94 - 97%) show higher whiteness value than those of WA and PA (L^*: 82 - 91%).

• Journal of Microbiology and Biotechnology
• /
• v.17 no.8
• /
• pp.1344-1352
• /
• 2007

An opportunistic human pathogen, Pseudomonas aeruginosa, contains the major catalase KatA, which is required to cope with oxidative and osmotic stresses. As an attempt to uncover the $H_2O_2$-dependent regulatory mechanism delineating katA gene expression, four prototrophic $H_2O_2$-sensitive mutants were isolated from about 1,500 TnphoA mutant clones of P. aeruginosa strain PA14. Arbitrary PCR and direct cloning of the transposon insertion sites revealed that one insertion is located within the katA coding region and two are within the coding region of oxyR, which is responsible for transcriptional activation of several antioxidant enzyme genes in response to oxidative challenges. The fourth insertion was within PA3815 (IscR), which encodes a homolog of the Escherichia coli iron-sulfur assembly regulator, IscR. The levels of catalase and SOD activities were significantly reduced in the iscR mutant, but not in the oxyR mutant, during the normal planktonic culture conditions. These results suggest that both IscR and OxyR are required for the optimal resistance to $H_2O_2$, which involves the expression of multiple antioxidant enzymes including KatA.