• 한국표면공학회지
• /
• 제45권5호
• /
• pp.206-211
• /
• 2012

Process analysis was carried out during deposition of MgO by inductively coupled plasma assisted reactive magnetron sputtering in Ar and $O_2$ ambient. At the initiation of Mg sputtering with bipolar pulsed dc power in Ar ambient, total pressure showed sharp increase and then slow fall. To analyse partial pressure change, QMS was used in downstream region, where the total pressure was maintained as low as $10^{-5}$ Torr during plasma processing, good for ion source and quadrupole operation. At base pressure, the major impurity was $H_2O$ and the second major impurity was $CO/N_2$ about 10%. During sputtering of Mg in Ar, $H_2$ soared up to 10.7% of Ar and remained as the major impurity during all the later process time. When $O_2$ was mixed with Ar, the partial pressure of Ar decreased in proportion to $O_2$ flow rate and that of $H_2$ dropped down to 2%. It was understood as Mg target surface was oxidized to stop $H_2$ emission by Ar ion sputtering. With ICP turned on, the major impurity $H_2$ was converted into $H_2O$ consuming $O_2$ and C was also oxidized to evolve CO and $CO_2$.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집 Vol.3 No.2
• /
• pp.609-612
• /
• 2002

In this study, the electrical properties were investigated for the deposited Ba,Sr)(Nb,Ti)$O_3$[BSNT] thin films grown on $Pt/TiO_2/SiO_2/Si$ substrate by RF sputtering method. The structural properties of the BSNT thin films affected by the $Ar/O_2$ rates were investigated. In the case of the BSNT thin films deposited with condition of 60/40$(Ar/O_2)$ ratio, the $BaTiO_3$, $SrTiO_3$ and $BaNbO_3$ phases were showed. The composition ratio of Nb and Ti in the BSNT thin films were nearly equivalent. Also, in the BSNT thin films deposited with condition of 60/40 and 80/20$(Ar/O_2)$ ratios, the composition of Ba, Sr, Nb and Ti were relatively uniform. The Ba, Sr, Nb and Ti in the BSTN thin films were not diffused into the Pt layer.

• 한국전기전자재료학회논문지
• /
• 제15권5호
• /
• pp.388-392
• /
• 2002

In this work, the etching of $CeO_2$ thin films has been performed in an inductively coupled $Ar/CF_4/Cl_2$ plasma. The highest etch rate of the $CeO_2$ thin film ws 250 ${\AA}/min$ and the selectivity of CeO$_2$to SBT was 0.4 at a 10% additive $Cl_2$ into Ar/($Ar+CF_4$)gas mixing ratio of 0.8. From result of X-ray photoelectron spectroscopy (XPS) analysis, there are Ce-Cl and Ce-F bonding by chemical reaction between Cl, F and Ce. During the etching of $CeO_2$ thin films in $Ar/CF_4/Cl_2$ plama, Ce-Cl and Ce-F bond is formed, and these prodcuts can be removed by the physical bombardment of Ar ions. The 10% additive $Cl_2$ into the Ar/($Ar+CF_4$)gas mixing ratio of 0.8 could enhance the reaction between Cl, F and Ce.

• 한국재료학회지
• /
• 제15권8호
• /
• pp.518-520
• /
• 2005

Effects of the $O_2/Ar$ flow ratio in the sputtering process on the crystallinity, surface roughness, carrier concentration, carrier mobility, and optical properties of Al-doped ZnO thin films deposited on sapphire (001) substrates by RF magnetron sputtering were investigated. XRD spectra showed a preferred orientation along the c-axis and a minimum FWHM of the (002) XRD intensity peak for the $O_2/Ar$ flow ratio of 0.5. The (101)peak also appeared and the degree of preferred orientation decreased as the $O_2/Ar$ flow ratio increased from 0.5 to 1.0. AFM analysis results showed that the surface roughness was lowest at the $O_2/Ar$ flow ratio of 0.5 and tended to increase owing to the increase of the grain size as the $O_2/Ar$ flow ratio increased further. According to the Hall measurement results the carrier concentration and carrier mobility of the fan decreased and thus the resistivity increased as the $O_2/Ar$ flow ratio increased. The transmittance of the ZnO:Al film deposited on the glass substrate was characteristic of a standing wave. The transmittance increased as the $O_2/Ar$ flow ratio in-RF magnetron sputtering increased up to 0.5. Considering the effects of the $O_2/Ar$ flow ratio on the surface roughness, electrical resistivity and transmittance properties of the ZnO:Al film the optimum $O_2/Ar$ flow ratio was 0.5 in the RF magnetron sputter deposition of the ZnO:Al film.

• 한국전기전자재료학회논문지
• /
• 제16권4호
• /
• pp.317-321
• /
• 2003

In this study, the structural properties were Investigated for the deposited (Ba,Sr)(Nb,Ti)O$_3$[BSNT] thin films grown on Pt/TiO$_2$/SiO$_2$/Si substrate by RF sputtering method. The structural properties of the BSNT thin films affected by the Ar/02 ratios were Investigated. In the case of the BSNT thin films deposited with condition of 60/40(Ar/O$_2$) ratio, the BaTiO$_3$, SrTiO$_3$ and BaNbO$_3$ phases were showed. The composition ratio of Nb and Ti in the BSNT thin films were nearly equivalent. Also, in the BSNT thin films deposited with condition of 60/40 and 80/20(Ar/O$_2$) ratios, the composition of Ba, Sr, Nb and Ti were relatively uniform. The Ba, Sr, Nb and Ti in the BSTN thin films were not diffused into the Pt layer.

• 마이크로전자및패키징학회지
• /
• 제14권3호
• /
• pp.15-20
• /
• 2007

플라스틱 기판에 적용이 가능한 최대 공정온도 $270^{\circ}C$ 이하에서 ZnO-TFT 소자를 제작하였다. ZnO-TFT 소자는 bottom gate 구조로 제작되었으며, ICP-CVD로 형성된 $SiO_2$ 산화물 게이트 공정을 제외하고는 모든 박막증착 공정은 RF-magnetron sputtering process를 이용하였다. ZnO 박막은 Ar과 $O_2$ gas 유량의 비율에 따라 여러 가지 조건에서 RF-magnetron sputtering 시스템을 이용하여 상온에서 증착하였다. Ar과 $O_2$ gas의 비율에 따라 제작된 TFT 소자는 모두 enhancement 모드의 소자특성을 나타내었고, 또한 가시광선영역에 있어 80% 이상의 높은 투과율을 보였다. ZnO 증착시 순수 Ar을 사용하여 제작된 ZnO-TFT의 경우에, $1.2\;cm^2/Vs$의 field effect mobility, 8.5 V의 threshold voltage, 그리고 $5{\times}10^5$의 높은 on/off ratio, 1.86 V/decade의 swing voltage로 가장 우수한 전기적 특성을 보였다.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2009년도 추계학술대회 초록집
• /
• pp.223-224
• /
• 2009

본 연구에서는 $Cl_2$/Ar 기반의 플라즈마 식각에 $N_2$가스를 첨가하여 ZnO 박막을 식각 하였을 때 관찰된 ZnO 박막의 식각 특성에 관하여 연구 하였다. ZnO 박막 식각 실험은 RF 800 W, bias power 400 W, 공정 압력 15 mTorr를 기준으로 하였으며 가스 혼합 비율로는 최적의 식각률을 보여주는 $Cl_2$/Ar=8:2 비율에서 실행하였다. 연구의 목적인 첨가 가스 $N_2$를 $Cl_2$ (80%)/Ar (20)%에 5 sccm 씩 첨가하여 20 sccm 까지 증가 시켜 실험 하였다. $N_2$ 가스가 15 sccm 첨가되었을 때 식각률 95.9 nm/min로 기존 $Cl_2$/Ar 기반의 플라즈마 식각보다 높은 식각률을 보여 주었으며 $N_2$ 가스 흐름 조절 외에도 공정 압력, RF power, bias power를 변경하며 실험하였다. 식각된 ZnO 박막의 표면은 최대 식각률을 보이는 공정 조건을 찾기 위해 surface profiler ($\alpha$-step)을 이용하여 식각률을 측정하였으며 ZnO 박막 표면의 화학적인 변화를 조사하기 위해 x-ray photoelectron spectroscopy (XPS)를 사용하였다. XPS 분석 결과 Zn $2p_{3/2}$ peak 가낮은 binding energy 쪽으로 이동한 것을 관찰 할 수 있었다. 또한 O 1s 의 스펙트럼을 분석한 결과 N-O bond와 O-H bond가 존재함이 밝혀졌다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1998년도 추계학술대회 논문집
• /
• pp.243-246
• /
• 1998

(Ba, Sr)TiO$_3$[BST] thin films were fabricated on Pt/SiO$_2$/Si substrate by RF sputtering technique. The structural, dielectric and electrical properties of BST thin films were investigated with Ar/O$_2$ ratio. Dielectric constant and dielectric loss of the BST thin film were about 1020 and 2.0[%], respectively. (at RF power 80W, post annealing temperature $650^{\circ}C$, deposition pressure of 5mTorr and Ar/O$_2$=80/20). For the BST(Ar/O$_2$=80/20) thin film with Polarization switching cycles of 10$^{10}$ , remanent polarization and coercive field were 0.084[$\mu$C/cm$^2$], 1.954[kV/cm], respectively.

• 한국전기전자재료학회논문지
• /
• 제13권7호
• /
• pp.617-624
• /
• 2000

Zinc Oxide(ZnO) thin films on Si(100) substrate were deposited by RF magnetron reactive sputtering. The charcteristics of ZnO thin films on argon/oxygen(Ar/O$_2$)gas ratios RF power and substrate temperature were investigated by XRD, SEM, and AFM analyses. C-axis preferred orientation resistivity and surface roughness highly depended on Ar/O$_2$gas ratios. The resistivity of ZnO thin films rapidly increased with increasing oxygen ratio and the resistivity value of 9$\times$10$^{7}$ $\Omega$cm was obtained at a working pressure of 10 mTorr with Ar/O$_2$=50/50. The surface roughness was also improved with increasing oxygen ratio and the ZnO films deposited with Ar/O$_2$=50/50 showed the excellent roughness value of 28.7$\AA$.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.127-128
• /
• 2009

CCP방식의 식각에 있어서 CF4/O2 Plasma Etch에 Ar을 첨가함으로써 Etch특성이 어떻게 변화하는지를 조사하였다. FE-SEM를 이용하여 Etch Profile를 측정하였다. 또한 Elipsometer와 Nanospec을 이용하여 Etch rate를 측정하였다. Ar의 비율이 전체의 47%정도를 차지하였을 때까지 Etch Profile이 향상되었다가 그이후로는 다시 감소하는 것을 볼 수 있었다. Ar을 첨가할수록 etch rate은 계속 향상되었다. Ar을 첨가하는 것은 물리적인 식각으로 반응하여 Etch rate의 향상과 적정량의 Ar을 첨가했을 때 Etch profile이 향상되는 결과를 얻었다.