• Journal of the Korean Society of Safety
• /
• v.19 no.4 s.68
• /
• pp.74-79
• /
• 2004

[ $CO_3O_4/{\gamma}-Al_2O_3$ ] catalysts were reported high activity on the low temperature CO oxidation. The effects of the calcination temperature, the loaded amount of cobalt and the oxygen concentration on the characteristics of CO oxidation have been investigated for a emergency escape mask cartridge. $Co(NO_3)_2\cdot6H_2O$ was used as cobalt precursor and the catalysts were prepared by incipient wetness impregnation. TGA shows that enough calcination is accomplished at $450^{\circ}C$ and cobalt phase is $Co_3O_4$ after calcination in the temperature range of $300\ ~500^{\circ}C$. The specific surface area and pore volume of catalysts are decreased with increasing of loaded amount of cobalt. And with the increase of loaded amount of cobalt and the oxygen concentration, the catalytic activity is increased.

• Korean Journal of Materials Research
• /
• v.29 no.6
• /
• pp.356-362
• /
• 2019

$BaSiO_3:RE^{3+}$ (RE = Sm or Eu) phosphor powders with different concentrations of activator ions are synthesized using the solid-state reaction method. The effects of the concentration of activator ions on the structural, photoluminescent, and morphological properties of the barium silicate phosphors are investigated. X-ray diffraction data reveals that the crystal structure of all the phosphors, regardless of the type and the concentration of the activator ions, is an orthorhombic system with a main (111) diffraction peak. The grain particles agglomerate together to form larger clusters with increasing concentrations of activator ions. The emission spectra of the $Sm^{3+}$-doped $BaSiO_3$ phosphors under excitation at 406 nm consist of an intense orange band at 604 nm and three weak bands centered at 567, 651, and 711 nm, respectively. As the concentration of $Sm^{3+}$ increases from 1 to 5 mol%, the intensities of all the emission bands gradually increase, reach maxima at 5 mol% of $Sm^{3+}$ ions, and then decrease significantly with further increases in the $Sm^{3+}$ concentration due to the concentration quenching phenomenon. For the $Eu^{3+}$-doped $BaSiO_3$ phosphors, a strong red emission band at 621 nm and several weak bands are observed. The optimal orange and red light emissions of the $BaSiO_3$ phosphors are obtained when the concentrations of $Sm^{3+}$ and $Eu^{3+}$ ions are 5 mol% and 15 mol%, respectively.

• Journal of the Microelectronics and Packaging Society
• /
• v.27 no.4
• /
• pp.11-17
• /
• 2020

Copper has been proved to be the best catalyst for electrochemical CO2 reduction reaction, however, for optimal efficiency and selectivity, its performance requires improvements. Electrochemical CO2 reduction reaction (RR) using CuO nanowire electrode was performed with different concentrations of KHCO3 electrolyte (0.1 M, 0.5 M, and 1 M). Cu(OH)2 was formed on Cu foil, followed by thermal-treatment at 200℃ under the air atmosphere for 2 hrs to transform it to the crystalline phase of CuO. We evaluated the effects of different KHCO3 electrolyte concentrations on electrochemical CO2 reduction reaction (RR) using the CuO nanowire electrode. At a constant current (5mA), low concentrated bicarbonate exhibited a more negative potential -0.77 V vs. Reversible Hydrogen Electrode (RHE) (briefly abbreviated as VRHE), while the negative potential reduced to -0.33 VRHE in the high concentration of bicarbonate solution. Production of H2 and CH4 increased with an increased concentration of electrolyte (KHCO3). CH4 production efficiency was high at low negative potential whereas HCOOH was not influenced by bicarbonate concentration. Our study provides insights into efficient, economically viable, and sustainable methods of mitigating the harmful environmental effects of CO2 emission.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.9
• /
• pp.846-850
• /
• 2005

[ $SrTiO_3$ ]:Al, Pr red phosphors for FED were synthesized by solid state reaction method. The dependence of their luminescent properties on Sr and Al concentration was investigated. The $SrTiO_3$: Al, Pr phosphors showed the characteristic X-ray diffraction patterns of the perovskite structure. Photoluminescence intensity and lattice constant in $SrTiO_3$: Al, Pr phosphors changed in quite a similar manner with Sr concentration. Photoluminescence intensity increased with increasing lattice constant, and the decrease of photoluminescence intensity and lattice constant occurred in the vicinity of 1 mol Sr concentration.

• Journal of the Korean Applied Science and Technology
• /
• v.22 no.2
• /
• pp.175-181
• /
• 2005

The spherical particles of $CeO_2/SiO_2$ composite powder with narrow-size distribution and pure phase particles were synthesized by ultrasonic spray pyrolysis method from aqueous cerium sulfate solution. The resulting composite powder was characterized by X-ray diffraction, scanning electron microscopy, transmittance electron microscopy, in-vitro sun protect factor, and BET surface area analysis. The concentration of cerium sulfate was tested to vary the particle size from $3.40{\times}10^{-3}$ to $1.02{\times}10^{-2}mol/cm^3$ to study concentration effect of starting material. The average particle size from the $3.40{\times}10^{-3}mol/cm^3$ concentration was found to be slightly smaller than that from the $1.02{\times}10^{-2}mol/cm^3$ concentration, because of the relation between the droplet size and the concentration of the starting material solution.

• Applied Chemistry for Engineering
• /
• v.18 no.5
• /
• pp.495-500
• /
• 2007

The inside wall of a coal gasifier is lined with refractory, and the corrosion of the refractory is an important factor affecting the refractory lifetime and the replacement period. This paper examines the changes in microstructure of a chromia refractory due to chemical reactions with slag having varying amounts of $Fe_2O_3$. Slag samples were prepared by adding $Fe_2O_3$ to KIDECO slag, and static corrosion experiments were carried out at $1550^{\circ}C$. The layer of $(Fe,Cr)_3O_4$ formation and the depth of Fe depletion in the infiltrating slag were determined. In addition, FactSage equilibrium calculations were carried out in order to determine the conditions of formation, and to compare with the experimental observations. In the sample exposed to KIDECO slag, which has about 10 wt% $Fe_2O_3$, the formation of $(Fe,Cr)_3O_4$ was not observed. As the $Fe_2O_3$ concentration in slag increased, $(Fe,Cr)_3O_4$ formation and Fe depletion depth increased. Increasing $Fe_2O_3$ concentration also made the slag/refractory interface indistinguishable. Equilibrium calculations predicted that higher $Fe_2O_3$ concentrations favor chromite formation at gasification temperatures. The chromite formation was most favorable when the amount of $Cr_2O_3$ was limited, as in the case of dissolved $Cr_2O_3$ in slag. When the concentration of $Fe_2O_3$ in slag was less than 20%, the formation of chromite was least favorable in the system with equal amounts of slag and refractory.

• Journal of Electrochemical Science and Technology
• /
• v.8 no.3
• /
• pp.197-205
• /
• 2017

Lead dioxide thin films were electrodeposited on nickel substrate from acidic lead nitrate solution. Current efficiency and thickness measurements, cyclic voltammetry, AFM, SEM, and X-ray diffraction experiments were conducted on $PbO_2$ surface to elucidate the effect of lead nitrate concentration, current density, temperature on the morphology, chemical behavior, and crystal structure. Experimental results showed that deposition efficiency was affected by the current density and solution concentration. The film thickness was independent of current density when deposition from high $Pb(NO_3)_2$ concentration, while it decreased for low concentration and high current density deposition. On the other hand, deposition temperature had negative effect on current efficiency more for lower current density deposition. Cyclic voltammetric study revealed that comparatively more ${\beta}-PbO_2$ produced compact deposits when deposition was carried out from high $Pb(NO_3)_2$ concentration. Such compact films gave lower charge discharge current density during cycling. SEM and AFM studies showed that deposition of regular-size sharp-edge grains occurred for all deposition conditions. The grain size for high temperature and low concentration $Pb(NO_3)_2$ deposition was bigger than from low temperature and high concentration deposition conditions. While cycling converted all grains into loosely adhered flappy deposit with numerous pores. X-ray diffraction measurement indicates that high concentration, high temperature, and high current density favored ${\beta}-PbO_2$ deposition while ${\alpha}-PbO_2$ converted to ${\beta}-PbO_2$ together with some unconverted $PbSO_4$ during cycling in $H_2SO_4$.

• Journal of Environmental Science International
• /
• v.30 no.5
• /
• pp.413-424
• /
• 2021

In this study, we quantitatively analyze the effect of ocean emission sources on the simulated O₃ concentrations in South Korea using the community multi-scale air quality (CMAQ) model. To analyze changes in O₃ concentrations by ocean emissions, two different CMAQ simulations considering ocean emissions (OE case) and without considering ocean emissions (NE case) were conducted during the Korea-United States air quality (KORUS-AQ) campaign period (May-June 2016). The changes in the simulated O₃ concentrations due to the effect of ocean emissions (OE case-NE case) appeared mostly in the ocean areas (+1.201 ppbv). The effect of ocean emissions was positive during the daytime (+1.813 ppbv), but negative during the nighttime (-0.612 ppbv). Analysis using the integrated process rate (IPR) confirmed that the increase or decrease in O₃ concentration by ocean emissions was mainly due to chemical processes. Further analysis using the integrated reaction rate (IRR) showed that the daytime increase in O₃ concentration was mainly attributable to the increased O₃ production via O + O₂ + M → O₃ + M reaction as photolysis of NO₂ increased due to the added ocean emissions. The nighttime decrease in O₃ concentration was mainly due to the increased O₃ titration by NO (NO + O₃ → O₂ + NO₂) due to the increased NO emission. These results indicate that the changes in the concentration O₃ in the sea area by the effect of ocean emissions are mainly due to increased NO_x emissions. However, there could be a number of uncertainties in ocean emissions data used in this study, thus continuous comparative research using the most updated data will need to be carried out in the future.

• Asian Journal of Atmospheric Environment
• /
• v.2 no.2
• /
• pp.81-89
• /
• 2008

The numerical simulation of wind and ozone ($O_3$) transport in mountainous regions was performed with a computational fluid dynamics technique. A dry deposition model for $O_3$ was designed to estimate $O_3$ deposition in complex terrain, and the qualitative validity of the predicted $O_3$ concentration field was confirmed by comparison with observed data collected with passive samplers. The simulation revealed that wind velocity increases around ridge lines and peaks of mountains. The areas with strong wind corresponded well with the sites of tree decline at high altitudes, suggesting that it is an important factor in the localization of tree/forest decline. On the other hand, there is no direct relationship between forest decline and $O_3$ concentration. The $O_3$ concentration, however, tends to increase as wind velocity becomes higher, thus the $O_3$ concentration itself may be a potential secondary factor in the localized decline phenomena. While the diffusion flux of $O_3$ is not related to localized tree decline, the pattern of advection flux is related to those of high wind velocity and localized tree decline. These results suggest that strong wind with large advection flux of $O_3$ may play a key role in the promotion of tree/forest decline at high mountain ridges and peaks.

• Journal of Environmental Science International
• /
• v.13 no.3
• /
• pp.289-295
• /
• 2004

The objective of this study is to delineate removal efficiency of the MTBE in solution by $TiO_2$ photocatalytic degradation as a function of the following different experimental conditions: Initial concentration of MTBE, air flow rate in solution, $H_2O_2$ dosage and pH of the solution. Photodegradation rate was increased with decreasing initial concentration of MTBE. The removal efficiency was 82% after 180 min in the case of MTBE concentration of 100 mg/L but 100% after 180 min in the case of 20 mg/L. Removal efficiency was increased with increasing pH, $H_2O_2$ dosage and air flow rate in solution.