• 한국전기전자재료학회논문지
• /
• 제29권2호
• /
• pp.90-94
• /
• 2016

In this work, [$Pb(Mg_{1/2}W_{1/2})_{0.03}(Ni_{1/3}Nb_{2/3})_x(Zr_{0.5}Ti_{0.5})_{0.97-x}O_3-BiFeO_3$] (x=0.02 to 0.12) composition ceramics were fabricated by the conventional soild state reaction method and their microstructure and piezoelectric properties were investigated according to PNN substitution. The addition of small amount of $BiFeO_3$, $Li_2CO_3$, and $CaCO_3$ were used in order to decrease the sintering temperature of the ceramics. The XRD (x-ray diffraction patterns) of all ceramics exhibited a perovskite structure. The sinterability of PMW-PNN-PZT-BF ceramics was remarkably improved using liquid phase sintering of $CaCO_3$, $Li_2CO_3$. However, it was identified from of the X-ray diffraction patterns that the secondary phase formed in grain boundaries decreased the piezoelectric properties. According to the substitution of PNN, the crystal structure of ceramics is transformed gradually from a tetragonal to rhombohedral phase. The x=0.10 mol PNN-substituted PMW-PNN-PZT-BF ceramics sintered at $920^{\circ}C$ showed the optimum values of piezoelectric constant($d_{33}$), piezoelectric figure of merit($d_{33{\cdot}}g_{33}$), planar piezoelectric coupling coefficient($k_p$) and density : $d_{33}=566$ [pC/N], $g_{33}=29.28[10^{-3}mV/N]$, $d_{33{\cdot}}g_{33}=16.57[pm^2/N]$, $k_p=0.61$, density=7.82 [$g/cm^3$], suitable for duplex ultrasonic sensor application.

• 한국재료학회지
• /
• 제8권12호
• /
• pp.1165-1169
• /
• 1998

제1세대 니켈계 단결정 초합금인 CMSX 6를 사용하여 셀렉타법으로 진공 정밀주조하여 단결정을 제작하였다. 주형온도 약 150$0^{\circ}C$, 주입온도 약 163$0^{\circ}C$와 용탕 주입 직후 주형을 2.5mm/분 속도로 하강시켜 단결정을 성장시켰다. 단결정 주조조직에서 기지와 공정조직은 ${\gamma}$' 석출물(Ni$_3$(Al, Ti)) 모양과 크기에 따라 각각 모두 두영역으로 구분되었으며, 공정조직의 Ti함랗은 기지보다 높았다. 즉, EPMA 및 CBED 분석 등으로 ${\gamma}$' 석출물을 분석한 결과, 기지내의 ${\gamma}$'은 크기가 0.5~0.7$\mu\textrm{m}$ 이하이며 화학조성상 Ni$_3$Al에 가까웠으며 격자구조도 Ll$_2$를 나타내었다. 반면에 공정조직에 가까울수록 ${\gamma}$' 크기는 1.0$\mu\textrm{m}$보다 컸으며, 모양도 판상형의 거대한 모양으로 바뀌었다. 화학조성 또한 Ni$_3$Ti에 가까웠으며 격자구조도 D $O_{24}$를 나타내었으므로 수지상과 공정조직의 ${\gamma}$' 석출물은 화학조성 및 격자구조가 상이함을 알 수 있었다.

• 한국전기전자재료학회논문지
• /
• 제26권2호
• /
• pp.98-103
• /
• 2013

The alumina substrates that Ni electrode was printed on and the multi-layered PTCR thermistors of which composition is $(Ba_{0.998}Ce_{0.002})TiO_3+0.001MnCO_3+0.05BN$ were fabricated by a thick film process, and the effect of re-oxidation temperature on their resistivities and resistance jumps were investigated, respectively. Ni electroded alumina substrate and the multi-layered PTC thermistor were sintered at $1150^{\circ}C$ for 2 h under $PO_2=10^{-6}$ Pa and then re-oxidized at $600{\sim}850^{\circ}C$ for 20 min. With increasing the re-oxidation temperature, the room temperature resistivity increased and the resistance jump ($LogR_{290}/R_{25}$) decreased, which seems to be related to the oxidation of Ni electrode. The small sized chip PTC thermistor such as 2012 and 3216 exhibits a nonlinear and rectifying behavior in I-V curve but the large sized chip PTC thermistor such as 4532 and 6532 shows a linear and ohmic behavior. Also, the small sized chip PTC thermistor such as 2012 and 3216 is more dependent on the re-oxidation temperature and easy to be oxidized in comparison with the large sized chip PTC thermistor such as 4532 and 6532. So, the re-oxidation conditions of chip PTC thermistor may be determined by considering the chip size.

• 마이크로전자및패키징학회지
• /
• 제18권3호
• /
• pp.9-17
• /
• 2011

Nano-composite solders have been studied to improve the properties of Pb-free solder joints. The nanoparticles in the composite solders were carbon nanotubes(CNTs), metals (Ag, Ni, Cr, etc.), ceramics (SiC, $ZrO_2$, $TiB_2$, etc.). To fabricate the nano-composite solders, mechanical mixing methods and in-situ fabrication method has been used for well-dispersed nano phase. The characteristic properties of the nano-composite solders were high creep resistance, low undercooling, low IMC growth rate and fine microstructures. More researches on the nano-composite solders are required to improve the processibility and the reliability of the nano-composite solder joints.

• 한국해양공학회지
• /
• 제15권3호
• /
• pp.69-74
• /
• 2001

This paper was to investigate of a adhesiveness for the plasma sprayed coating materials did salt spray by acoustic emission method in tensile loadings. The powders used for the coating were nickel aluminum composite powder Ni-4.5wt.%Al and titanium dioxide powder $TiO_2$. These powders were coated on a carbon steel S45C by plasma spray method. The result solution was a 5% NaCl and the slat spray times were 2, 5 and 10 hours respectively. The salt solution penetrated into the surface of the substrate through pore of the coating layer built in the process of plasma spay. Corrosion productions formed on the surface of substrate. The adhesiveness between the substrate and the coating layer is weaken by corrosion and the exfoliation initiated chiefly at the corrosion surface of the substrate. The AE events and energy of the corroded coating specimens decreased as the salt spray times increased.

• 동력기계공학회지
• /
• 제2권3호
• /
• pp.49-54
• /
• 1998

This paper is investigated of hardness and adhesiveness of plasma sprayed coating steels by AE(Acoustic Emission) testing when loading a tensile. AE Parameters used are Event, Count, Energy and Amplitude. Test specimens are carbon steel(S45C) with sprayed coating layers of Ni-4.5wt.%Al(bond coating) and $TiO_2$(top coating), and carry out heat treatment at $800^{\circ}C\;and\;1000^{\circ}C$, respectively. The micro-hardness of the heat treatment specimen have been improved more than that of non-heat treatment. On the tensile test, the process and occurence of the exfoliation of the sprayed coating layer can be estimated by AE Characteristics of AE parameters, such as event, count, amplitude and energy, on the layer exfoliation are shown the similar aspects. The exfoliation of bond coating occure at about 20% of strain and top coating is about 5% of strain.

• 한국전기전자재료학회논문지
• /
• 제15권7호
• /
• pp.597-601
• /
• 2002

In this study, the structural, dielectric and piezoelectric properties of $Pb[(Ni_{1/3}Nb_{2/3})_x-(Mn_{1/3}Nb_{2/3})_{0.09-x}-(Zn_{0.505}Ti_{0.495)_0.91]O_3$ (x=0, 0.01, 0.02, 0.03, 0.04, 0.05) system ceramics were investigated to develop the composition ceramics for piezoelectric transformer. All the specimens were sintered at $1250^{\circ}C$ and its physical properties were measured, and the results are as follows : With increasing PNN substitution for PMN-PZT system, dielectric constant was increased and electro-mechanical coupling factor($k_p$) was increased to 0.62 at 5 mol% while mechanical quality factor(Qm) was decreased.

• 한국표면공학회지
• /
• 제31권4호
• /
• pp.209-216
• /
• 1998

It is well knownthat electroledd plating is the desirable surface treatment method which is being widely used to all kinds of material such as requiring corrosing resistance, wear resistance and conductivity, especially nonconductivity materials' surface plating. However, it is suggested that there are some problems that must be solved, for exaple, rate of plating, corrosion resistance, thickness of plating film etc. Therefore in this paper, when electroless nickel plating was performed on the PZT(Pb(Zr,Ti))with varying of solution composition such as NaOH, and $H_2NCH_2COOH$, the effect of the rate of plating and corrosion resistance were investigated.

• 한국전기전자재료학회논문지
• /
• 제30권8호
• /
• pp.496-500
• /
• 2017

$Pb(Mn_{1/3}Nb_{2/3})_{0.07}(Ni_{1/3}Nb_{2/3})_{0.10}(Zr_{0.5}Ti_{0.5})_{0.83}O_3$ composition ceramics with high piezoelectric properties were fabricated by the columbite precursor method for ultrasonic generators, and the effects of sintering temperature on microstructure and piezoelectric properties were systematically investigated. It was found that the tetragonality of the ceramics decreased with increase in sintering temperature. Moreover, excellent physical properties such as $d_{33}=447pC/N$, ${\varepsilon}_r=1,843$, $k_p=0.641$, and $Q_m=1,207$ were obtained for an ultrasonic generator when the second calcination temperature and sintering temperature were $720^{\circ}C$ and $920^{\circ}C$, respectively.

• 한국산업보건학회지
• /
• 제24권4호
• /
• pp.547-555
• /
• 2014

Objective: This study was conducted to investigate the association between subjective distress symptoms and argon welding among workers in Gyeongnam Province shipyard. Method: 31 argon and 29 non-argon welding workers were selected as study subjects in order to measure concentrations of personal dust, welding fumes and other hazardous materials such as ZnO, Pb, Cr, FeO, MnO, Cu, Ni, $TiO_2$, MgO, NO, $NO_2$, $O_3$, $O_2$, $CO_2$, CO and Ar. An interviewer-administered questionnaire survey was also performed on the same subjects. The items queried were as follows: age, height, weight, working duration, welding time, welding rod amounts used, drinking, smoking, and rate of subjective distress symptoms including headache and other symptoms such as fever, vomiting and nausea, metal fume fever, dizziness, tingling sensations, difficulty in breathing, memory loss, sleep disorders, emotional disturbance, hearing loss, hand tremors, visual impairment, neural abnormality, allergic reaction, runny nose and stuffiness, rhinitis, and suffocation. Statistical analysis was performed using SPSS software, version 18. Data are expressed as the mean ${\pm}SD$. An ${\chi}^2$-test and a normality test using a Shapiro wilk test were performed for the above variables. Logistic regression analysis was also conducted to identify the factors that affect the total score for subjective distress symptoms. Result: An association was shown between welding type (argon or non-argon welding) and the total score for subjective distress symptoms. Among the rate of complaining of subjective distress symptoms, vomiting and nausea, difficulty breathing, and allergic reactions were all significantly higher in the argon welding group. Only the concentration of dust and welding fumes was shown to be distributed normally after natural log transformation. According to logistic regression analysis, the correlations of working duration and welding type (argon or non-argon) between the total score of subjective distress symptoms were found to be statistically significant (p=0.041, p=0.049, respectively). Conclusion: Our results suggest that argon welding could cause subjective distress symptoms in shipyard workers.