• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.70-73
• /
• 2001

MFIS(Metal-ferroelectric-insulator- semiconductor) structures using silicon oxynitride(SiON) buffer layers were fabricatied and demonstrated nonvolatile memory operations. Oxynitride(SiON) films have been formed on p-Si(100) by RTP(rapid thermal process) in O$_2$+N$_2$ ambient at 1100$^{\circ}C$. The gate leakage current density of Al/SiON/Si(100) capacitor was about the order of 10$\^$-8/ A/cm$^2$ at the range of ${\pm}$ 2.5 MV/cm. The C-V characteristics of Al/LiNbO$_3$/SiON/Si(100) capacitor showed a hysteresis loop due to the ferroelectric nature of the LiNbO$_3$ thin films. Typical dielectric constant value of LiNbO$_3$ film of MFIS device was about 24. The memory window width was about 1.2V at the electric field of ${\pm}$300 kV/cm ranges.

• Journal of the Korean Ceramic Society
• /
• v.37 no.8
• /
• pp.731-738
• /
• 2000

KLN(K3Li2Nb5O15) has attracted a great deal of attention for their potential usefulness in piezoelectric, electro-optic, nonlinear optic, and pyroelectirc devices. Especially, the KLN single crystal has been studied in the field of optics and electronics. However it is hard to produce good quality single crystals due to the crack propagation during crystal growing. One of the solutions of this problem is prepartion of thin film. But the intensive study has not been conducted so far. In this study, after the KLN thin film were prepared by R.F. magnetron Sputtering method on SiO2/Si substrate, the post-annealing methods of RTA(rapid thermal annealin) and IPA(insitu post annealing) were employed. The deposition condition of KLN thin film was RF power(100 W), Working pressure(100 mtorr). The commonness of both RAT and IPA was that the higher were deposition and post annealing temperature, the higher was the intensity of XRD but the less surface roughness. The difference of post-annealing methods affected XRD phase and surface condition very much. And in IPA process, the influence of O2 had much effect on the formation of KLN phase.

• Proceedings of the IEEK Conference
• /
• 2000.11b
• /
• pp.221-224
• /
• 2000

We have successfully demonstrated metal-ferroel-ectric-insulator-semiconductor (MFIS) devices using Al/LiNbO$_{3}$/SiN/Si structure. The SiN thin films were made into metal -insulator- semiconductor (MIS) devices by thermal evaporation of aluminum source in a dot away on the surface. The interface property of MFIS from 1MHz & quasistatic C-V is good and the memory window width is about 1.5V at 0.2V/s signal voltage sweep rate. The gate leakage current density of MFIS capacitors using a aluminum electrode showed the least value of 1x10$^{-8}$ A/$\textrm{cm}^2$ order at the electric field of 300㎸/cm. And the XRD patterns shows the probability of applications of LN for MFIS devices for FeRAMs on amorphous SiN buffer layer.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.9 no.3
• /
• pp.295-298
• /
• 1999

High quality of $Er_{2}O_{3}$ doped $LiNbO_{3}$ single crystal thin films were grown by the liquid phase epitaxial (LPE) method using $Er_{2}O_{3}$ doped at concentrations of 1,3, and 5 mol% respectively. After the growth of single crystal thin film, the crystallinity and the lattice mismatch along the c-axis between the film and the substrate was examined as a function of the variations of{{{{{Er}_{2}{O}_{3}}}}} dopant concentration using a X-ray double crystal technique. There was no lattice mismatch along the c-axis for the undoped film and those doped with 1 and 3 mol% of $Er_{2}O_{3}$. For 5 mol% of $Er_{2}O_{3}$ doped film, the lattice mismatch was $7.86{\times}10^{-4}$nm along the c-axis.

• Korean Journal of Materials Research
• /
• v.33 no.6
• /
• pp.229-235
• /
• 2023

An all-perovskite oxide heterostructure composed of SrSnO₃/Nb-doped SrTiO₃ was fabricated using the pulsed laser deposition method. In-plane and out-of-plane structural characterization of the fabricated films were analyzed by x-ray diffraction with θ-2θ scans and φ scans. X-ray photoelectron spectroscopy measurement was performed to check the film's composition. The electrical transport characteristic of the heterostructure was determined by applying a pulsed dc bias across the interface. Unusual transport properties of the interface between the SrSnO₃ and Nb-doped SrTiO₃ were investigated at temperatures from 100 to 300 K. A diodelike rectifying behavior was observed in the temperature-dependent current-voltage (IV) measurements. The forward current showed the typical IV characteristics of p-n junctions or Schottky diodes, and were perfectly fitted using the thermionic emission model. Two regions with different transport mechanism were detected, and the boundary curve was expressed by ln I = -1.28V - 13. Under reverse bias, however, the temperature- dependent IV curves revealed an unusual increase in the reverse-bias current with decreasing temperature, indicating tunneling effects at the interface. The Poole-Frenkel emission was used to explain this electrical transport mechanism under the reverse voltages.

• Journal of Sensor Science and Technology
• /
• v.16 no.5
• /
• pp.349-354
• /
• 2007

This paper presents characteristics of surface acoustic wave (SAW) gas sensor for detecting volatile gases such as ethanol gas by measuring the phase shift of output signal. A delay-line with a center frequency of 400 MHz was fabricated on $128^{\circ}$ Y-Z $LiNbO_{3}$ substrates. Experimental results, which showed the phase change of the output signal under the absorption of volatile gas on sensor surface, were presented. The sensitivities of SAW delay lines coated with polyurethane films were greatly increased compared to those for uncoated devices. This SAW gas sensor system may be well suited for a high sensitivity electronic nose system.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2009.08a
• /
• pp.168-168
• /
• 2009

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.489-493
• /
• 2004

[ $Ba_2NaNb_5O_{15}$ ]은 orthorhombic tungsten bronze 결정구조를 갖는 강유전체로서, 단결정의 경우 $LiNbO_3$에 비해 우수한 비선형 전광계수 값을 나타내는 것으로 알려져 있으며, 또한 주목할만한 초전, 압전, 강유전특성을 나타내고 있다. 본 연구에서는 다른 강유전체박막에 비하여 상대적으로 연구가 덜 이루어진 BNN 박막을 세라믹 타겟을 사용하여 이온빔 보조 증착법을 사용하여 제조하였으며, $Ar/O_2$ 분위기에서 증착된 BNN 박막에 대한 결정화 및 배향 특성을 고찰하였고, 이에 따른 전기적 특성의 변화를 살펴보았다. 연구에 사용된 기판은 $Pt(100)/TiO_2/SiO_2/Si(100)$이었으며, 이온빔 보조 증착법에서 보조 이온빔의 에너지를 $0{\sim}400eV$로 변화 시키며 BNN 박막을 증착한 후, 열처리하였다. BNN 박막의 전기적 특성은 MFM 박막 커패시터의 형태로 제조하여 강유전 특성에 대해 살펴보았다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.5
• /
• pp.410-416
• /
• 2001

KLN thin films were fabricated on Pt coated Si(100) wafer using an rf-magnetron sputtering method. The grown KLN thin film consists of 4-fold grains. In this experiment, the structure of 4-fold grained thin film was investigated using XRD and SEM measurements. Pt layer was also deposited using the rf-magnetron sputtering method,. XRD measurement showed that he Pt thin film has Gaussian distribution form with strong (111) direction orientation. The KLN thin film has preferred-orientation of (001) direction, and the peak consists of 2 separate peaks; one with broad FWHM and the other with narrow FWHM. The sharp peak is due to single crystal, and combining with Em results, the 4-fold grain consists of singel crystals with c-axis normal to substrate.

• Korean Journal of Materials Research
• /
• v.11 no.3
• /
• pp.178-184
• /
• 2001

Transparent and highly oriented KLN thin films have been grown by an rf- magnetron sputtering deposition method. A homogeneous and stable KLN target was prepared by calcine and sintering process. For KLN target, stoichiometry and composition excess with K of 30% and 60%, and Li of 15% and 30% respectively, was prepared. The targets were sintered at low temperature to prevent vaporization of K and Li. KLN thin films were fabricated by rf-magnetron sputtering method using those targets. In this experiment, using the target of composition excessed with K of 60% and Li of 30%, single phase KLN thin film was produced. KLN thin film has excellent crystallinity and highly c-axis oriented on Corning 1737 substrate. Transmittance of thin film in visible range was 90%, absorption edge is 333 nm and refractive index at 632.8 nm was 1.93.