• 한국안전학회지
• /
• 제31권1호
• /
• pp.66-73
• /
• 2016

Lyocell fibers were used as a precursor in order to improve yield and strength of cellulose-based precursor while manufacturing activated carbon fiber(ACF). Lyocell fibers as a precursor for the preparation of ACF were surface-modified by reaction with 3-aminopropyltriethoxysilane(APTES) and pre-treated with KOH and H3PO4. Using aforementioned precursor, ACFs were prepared by a series of stabilization, carbonization and activation process at high temperatures. On each process, FT-IR, TGA, UTM and SEM were used to observe fibers' physical properties including structure and porous surfaces. FT-IR results proved that surface modification was achieved during stabilization, carbonization and activation process. TGA results during carbonization process found that surface modified fibers with APTES 0.02 mol(A2) showed higher thermostability, and extended pre-treatment increased yield. Especially, yield was found to have an increase of 10~20 wt% with surface modification during activation process. UTM results showed that tensile strength has the same order of concentration of APTES after surface modification, however, was found to show lower tensile strength than lyocell fibers after stabilization process. SEM results revealed that more homogeneous porosity control could be proceed after modifying the surface for the effective removal of hazardous substances.

• 한국재료학회지
• /
• 제16권1호
• /
• pp.63-67
• /
• 2006

The characteristics of the wet-etching of ZnO thin films were investigated using hydrochloric and phosphoric acid solutions as etchants. The etch rate of ZnO films, using highly diluted hydrochloric acid solutions at a concentration of 0.25% in deionized water, was determined to be about 120 nm/min, and linearly increased with increasing the acid concentration, resulting in $1.17{\mu}m/min$ when a 2% HCl solution was used. The surface of ZnO etched by an HCl solution, observed by scanning electron microscopy, showed a rough morphology with a high density of hexagonal pyramids or cones with sidewall angles of about ${\sim}45^{\circ}C$. Moreover, the sidewall angles of the masked area were similar to those of the pyramids on the surface. In comparison, the surface of ZnO etched by a phosphoric acid had a smooth surface morphology. The origin of this difference is from the very initial stage of etching, indicating that the etch-mechanism is different for each solution. Furthermore, when $H_3PO_4$ was added to the HCl aqueous solution, the morphology of the etched surface was greatly enhanced and the sidewall angle was also increased to about $65^{\circ}C$.

• Journal of Ceramic Processing Research
• /
• 제20권6호
• /
• pp.655-659
• /
• 2019

Calcium phosphates such as HA (hydroxyapatite), β-TCP (tricalcium phosphate) and biphasic HA/β-TCP, were synthesized by wet chemical precipitation in aqueous solution combined with ball milling process. Nanosize powders of the calcium phosphates were synthesized using Ca(OH)2 and H3PO4. The effects of initial precursor Ca/P ratio (1.30, 1.50 and 1.67), ball milling process and post heat-treatment on the phase evolution behavior of the powders were investigated. The phase of resulting powder was controllable by adjusting the initial Ca/P ratio. HA was the only phase for as-prepared powders in both cases of Ca/P ratios of 1.50 and 1.67. The single HA phase without any noticeable second phase was obtained for the initial Ca/P ratio of 1.67 in the overall heat-treatment range. Pure β-TCP and biphasic calcium phosphate (HA/β-TCP) were synthesized from precursor solutions having Ca/P molar ratios of 1.30 and 1.50, respectively, after having been heat-treated above 700 ℃. The β-TCP phase has appeared on the pre-existing DCPD (dicalcium phosphate dihydrate) and/or HA phase. Dense ceramics having translucency were obtained at a considerably lower sintering temperature. The modified process offered a fast, convenient and economical route for the synthesis of calcium phosphates.

• 한국토양비료학회지
• /
• 제46권5호
• /
• pp.351-358
• /
• 2013

A suitable supply of mineral elements into shoot via a root system from growth media makes plants favorable growth and yield. The shortage or surplus of minerals directly affects overall physiological reactions to plants and, especially, strongly influences carbohydrate metabolism as a primary response. We have studied mineral uptake and synthesis and translocation of soluble carbohydrates in N, P or K-deficient tomato plants, and examined the interaction between soluble carbohydrates and mineral elements. Four-weeks-old tomato plants were grown in a hydroponic growth container adjusted with suboptimal N ($0.5mmol\;L^{-1}\;Ca(NO_3)2{\cdot}4H_2O$ and $0.5mmol\;L^{-1}\;KNO_3$), P ($0.05mmol\;L^{-1}\;KH_2PO_4$), and K ($0.5mmol\;L^{-1}\;KNO_3$) for 30 days. The deficiency of specific mineral element led to a significant decrease in its concentration and affected the concentration of other elements with increasing treatment period. The appearance of the reduction, however, differed slightly between elements. The ratios of N uptake of each treatment to that in NPK sufficient tomato shoots were 4 (N deficient), 50 (P deficient), and 50% (K deficient). The P uptake ratios were 21 (N deficient), 19 (P deficient), and 28% (K deficient) and K uptake ratios were 11 (N deficient), 46 (P deficient), and 7% (K deficient). The deficiency of mineral elements also influenced on carbohydrate metabolism; soluble sugar and starch was substantially enhanced, especially in N or K deficiency. In conclusion, mineral deficiency leads to an adverse carbohydrate metabolism such as immoderate accumulation and restricted translocation as well as reduced mineral uptake and thus results in the reduced plant growth.

• The Journal of Advanced Prosthodontics
• /
• 제5권3호
• /
• pp.226-233
• /
• 2013

PURPOSE. This study evaluated the adhesion of 10-MDP containing self-etch and self-adhesive resin cements to dentin with and without the use of etch-and-rinse technique. MATERIALS AND METHODS. Human third molars (N=180) were randomly divided into 6 groups (n=30 per group). Conventional (Panavia F2.0, Kuraray-PAN) and self-adhesive resin cements (Clearfil SA, Kuraray-CSA) were bonded to dentin surfaces either after application of 3-step etch-and-rinse (35% $H_3PO_4$ + ED Primer) or two-step self-etch adhesive resin (Clearfil SE Bond). Specimens were subjected to shear bond strength test using the universal testing machine (0.5 mm/min). The failure types were analyzed using a stereomicroscope and quality of hybrid layer was observed under a scanning electron microscope. The data (MPa) were analyzed using two-way ANOVA and Tukey's tests (${\alpha}$=.05). RESULTS. Overall, PAN adhesive cement showed significantly higher mean bond strength ($12.5{\pm}2.3-14.1{\pm}2.4$ MPa) than CSA cement ($9.3{\pm}1.4-13.9{\pm}1.9$ MPa) (P<.001). Adhesive failures were more frequent in CSA cement groups when used in conjunction with two-step self-adhesive (68%) or no adhesive at all (66%). Hybrid layer quality was inferior in CSA compared to PAN cement in all conditions. CONCLUSION. In clinical situations where bonding to dentin substrate is crucial, both conventional and self-adhesive resin cements based on 10-MDP can benefit from etch-and-rinse technique to achieve better quality of adhesion in the early clinical period.

• 한국환경과학회:학술대회논문집
• /
• 한국환경과학회 2006년도 학술발표회 발표논문집
• /
• pp.280-281
• /
• 2006

속초연안의 수온은 18개년 평균 표층수 $14.10\pm0.34^{\circ}C$, 저층수 $12.56\pm0.28^{\circ}C$, 염분은 표층수 $31.66\pm0.18$, 저층수 $32.68\pm0.10$, pH은 표층수 $8.05\pm0.01$, 저층수 $8.02\pm0.01$, BO는 표층수 $8.48\pm0.11mg/L$, 저층수 $8.16\pm0.12mg/L$, COD는 표층수 $1.54\pm0.07mg/L$, 저층수 $1.33\pm0.06mg/L$, SS는 표층수 $13.75\pm0.80mg/L$, $PO_4$-P는 표층수 $0.74\pm0.05{\mu}M$, 저층수 $0.61\pm0.04{\mu}M$, $NH_4$-N는 표층수 $2.49\pm0.18{\mu}M$, 저층수 $2.01\pm0.15{\mu}M$, $NO_2$-N는 표층수 $0.72\pm0.05{\mu}M$, 저층수 $0.58\pm0.04{\mu}M$, $NO_3$-N는 표층수 $4.39\pm0.24{\mu}M$, 저층수 $3.63\pm0.20{\mu}M$, DIN는 표층수 $7.64\pm0.38{\mu}M$, 저층수 $6.22\pm0.29{\mu}M$, DIN/DIP비 표층수 $23.91\pm3.42$, 저층수 $23.43\pm3.38$이었으며, 전반적으로 해역별 수질기준 I등급 내지는 II등급을 유지하고 있었고, 공간적으로는 외해측으로 갈수록 외해수와 혼합 확산되어 양호한 수질을 나타내었다. 장기적인 변동특성은 세그룹으로 구분되어진다.

• 한국환경과학회지
• /
• 제16권3호
• /
• pp.385-392
• /
• 2007

Currently, portable equipment for recycling of waste asphalt concrete (ASCON) has been used. However, any air pollution control devices are not attached in the simple portable one. Thus, a lot of air pollutants have been produced from recycling processes of waste ASCON which resulted from aging of paved roads or repavement of roads. This study deals with a preliminary result of concentration analysis of air pollutants obtained from a pilot and a real recycling processes of waste ASCON using simple portable recycling equipment. Air pollutants were taken from 4 steps of the pilot recycling process including an initial heating by liquid petroleum gas (LPG), intermediate heating and melting (H&M) process, final H&M process, and pavement processes using recycled ASCON at the recycling site. Also, air pollutants were taken front 4 steps of the real recycling processes including an initial H&M, final H&M and mixing, loading of recycled ASCON to dump trucks, and at the recycling site after leaving the loaded dump trucks for real pavement sites. The air pollutants measured in this study include volatile organic compounds (VOCs), aldehydes, particulate matter (PM: PM1, PM2.5, PM7, PM10, TSP (total suspended particulate)). The identified concentrations of VOCs increased with increasing time or degree for H&M of waste ASCON. In particular, very high concentrations of the VOCs at the status of complete melting, which is exposed to the air, of the waste ASCON just before paving tv the recycled ASCON at the recycling site. Also, considerable amount of VOCs were identified from the recycling equipment after the dump trucks leaded by recycled ASCON leaved the recycling site for the pavement sites. The relative level of formaldehyde exceeded 80% of the aldehydes Identified in the recycling processes. This is because the waste ASCON is exposed to direct flame of LPG during H&M processes. The PM concentrations measured in the winter recycling processes, such as the loading and rotation processes of waste ASCON into/in the recycling equipment for H&M, were much higher than those in the summer ones. In particular, the concentrations of coarse particles such as PM7 and PM10 during the winter recycling were very high as compared those during the summer one.

• 한국식품영양과학회지
• /
• 제31권3호
• /
• pp.428-432
• /
• 2002

김치 제조시에 칼슘 분말제재를 절인 배추에 대하여 0.5%, 1.0% 및 1.5%씩 첨가하여 김치를 만들고, 숙성하면서 pH, 적정산도, 환원당 함량, 총균수, 젖산균수 및 관능검사와 같은 품질 특성을 조사하였다. 대조구는 숙성 10일 이후에 pH 4.0 이하인데 반하여 칼슘 분말제재를 첨가한 시험구는 pH 4.0 이상을 유지하였으며, 1.5% 첨가구의 값이 가장 높았다. 적정산도는 숙성 25일까지 지속적으로 증가하였으며, 10일까지 증가가 다른 기간에 비하여 현저하였다. 또한 칼슘 분말제재 첨가구는 김치 담금시부터 대조구보다 높은 환원당 함량을 나타내었으며, 숙성 기간 중 그 차이는 큰 변화를 보이지 않았다. 숙성 5일까지는 총균수와 젖산균수가 급격하게 증가하여 9 log(CFU/mL)에 도달하였으며, 대조구의 총균수가 가장 많았다. 그러나 그 이후에는 칼슘 분말제재를 첨가한 시험구의 총균수가 대조구보다 대체적으로 많았다. 관능적인 평가에서는 칼슘분말 제재를 0.5%, 1.0% 첨가한 시험구가 냄새 및 맛에 있어서 대조구보다 높은 점수를 얻었으나 대조구와 유의적인 차이를 보이지는 않았다.

• 미생물학회지
• /
• 제50권3호
• /
• pp.201-209
• /
• 2014

본 연구에서는 고추재배 지역의 오염지 토양으로부터 탄저병원균인 Colletotrichum gloeosporioides에 대하여 항진균 활성이 우수한 균주를 분리하였다. 분리 균주의 생화학적 특성을 조사한 결과 내생포자를 형성하는 Gram-positive이며, 세포크기는 $2.5{\sim}3.0{\times}1.5{\mu}m$으로 짧은 간균으로 siderophore, cellulase와 IAA (Indole-3-acetic acid)을 생산하였다. 16S rRNA 유전자염기서열 분석 결과 Bacillus sp.와 99%의 상동성을 나타내어 Bacillus sp. CS-52로 명명하였다. Bacillus sp. CS-52의 항진균 활성 물질을 생산하기 위한 배양 최적 조건은 0.5% glucose, 0.7% $K_2HPO_4$, 0.2% $K_2HPO_4$, 0.3% $NH_4NO_3$, 0.01% $MnSO_4{\cdot}7H_2O$, 0.15% yeast extract, pH 7과 $30^{\circ}C$로 조사되었으며, 최적화된 배양조건에서 36시간에 최대 성장을 보이며, 고추 탄저병원균에 대하여 60시간 배양조건에서 가장 높은 13.3 mm의 항진균 활성을 보였다. 포자발아억제력은 48시간에 가장 높은 억제력이 보였고, siderophore는 최종배양시간 72시간까지 생성됨을 확인하였다. 식물생장조절물질 IAA와 활성효소인 cellulase의 경우 배양시간 24시간에 최대 생성됨을 확인하였으며, C. gloeosporioides에 대한 실내에서의 항진균활성 검증결과 화학농약 보다 더 높은 70%의 방제가를 나타내었다. 향후 Bacillus sp. CS-52 균주와 배양액을 이용하여 생물학적 친환경방제제로의 제품화가 가능할 것으로 사료된다.

• 한국균학회지
• /
• 제10권1호
• /
• pp.33-39
• /
• 1982

한국산고등균류(韓國産高等菌類)의 일종(一種)인 표고버섯을 진탕액내배양하며 이로부터 항암성다당체(抗癌性多糖體)를 분리(分離)하고 얻어진 항암성다당체(抗癌性多糖體)의 물리화학적(物理化學的) 특성(特性) 및 면역학적(免疫學的) 특성(特性)을 밝히고 그의 발효공업적(醱酵工業的)민 생산법(生産法)을 연구(硏究)하기 위하여 일차적으로 본연구(本硏究)의 목적(目的)에 적합(適合)한 균주(菌株)를 선발(選拔)하고 선발(選拔)된 균주(菌株)의 배양조건(培養條件)에 대한 기초적인 실험을 시행한바 그 결과는 다음과 같다. 1. 10개의 계통(系統)의 자실체(子實體)를 분석(分析)한 결과(結果) 자실체(子實體)의 다당체(多糖體) 함유율(含有率)이 가장 높으며 또한 7개의 계통별(系統別) 균사체(菌絲體)를 진탕액내배양하여 MDW를 비교한 결과(結果) 두 번째로 우수한 균주(菌株)인 L. edodes-DMC7(본실험실(本實驗室)에서 부여한 고유 번호임)을 본(本) 연구(硏究)에 사용(使用)할 균주(菌株)로 선발(選拔)하였다. 2. L. edodes-DMC7의 균사생장최적(菌絲生長最適) pH는 $5.0{\sim}5.5$이었다. 3. L. edodes-DMC7의 균사생장(菌絲生長)에 필요한 탄소원(炭素源)으로는 glucose보다 starch가 효과적이어서 glucose만을 탄소원(炭素源)으로 한 배지(培地)에서 보다는 glucose를 모두 starch로 대치하거나 일부만을 starch로 대치한 배지(培地)에서의의 균사생장(菌絲生長)이 $15{\sim}20%$ 우수함을 알 수 있었다. 4. L. edoeds-DMC7의 균사생장(菌絲生長)에 펼요한 질소원(窒素源)으로는 yeast extract가 효과적이어서 yeast extract를 단독으로 혹은 Peptone과 1 : 1로 혼합하여 질소원(窒素源)으로 사용할 경우 Peptone 또는 malt extract만을 질소원(窒素源)으로 사용한 경우보다 악 100%의 MDW증가를 볼 수 있었다. 5. L. edodes-DMC7의 균사생장(菌絲生長)에 적합(適合)한 배지(培地)의 최고농도(最高濃度)는 악 10%이며 이를 넘어서면 급격히 균사생장이 저해됨을 알 수 있었다. 6. L. edodes-DMC7의 균사생장(菌絲生長)은 배양제(培養第)12日만에정점에 이르며 따라서 이때를 균사수확의 시기로 볼 수 있다. 7. GRAP의 첨가(添加)로 인한 L. edodes-DMC7의 균사생장자극효과는 MDW가 배지(培地)당 100ml 1,000mg을 넘지못할 경우에만 인정되었다.